ASTM F654-2007(2012) Standard Specification for Residential Chain Link Fence Gates《住宅用链环栏栅门的标准规范》.pdf

《ASTM F654-2007(2012) Standard Specification for Residential Chain Link Fence Gates《住宅用链环栏栅门的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F654-2007(2012) Standard Specification for Residential Chain Link Fence Gates《住宅用链环栏栅门的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F654 07 (Reapproved 2012)Standard Specification forResidential Chain Link Fence Gates1This standard is issued under the fixed designation F654; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers detail requirements for resi-dential chain link fence gates, gate posts, and accessories.2. Referenced Doc

3、uments2.1 ASTM Standards:2A780 Practice for Repair of Damaged and Uncoated Areasof Hot-Dip Galvanized CoatingsF1043 Specification for Strength and Protective Coatings onSteel Industrial Fence FrameworkF626 Specification for Fence Fittings3. Classification3.1 Residential chain link fence gates are cl

4、assified asfollows:3.1.1 Type ISingle Swing3.1.2 Type IIDouble Swing3.2 No gate leaf over 6 ft (1.829 m) in height or over 6 ft(1.829 m) in width shall be classified as residential, regardlessof use or location.4. Manufacture4.1 Zinc-coated steel frames shall be zinc-coated in accor-dance with the z

5、inc coating specified for the fence framework.Welded joints shall have suitable rust preventive coatingapplied to the welds.4.2 Aluminum gate frame shall be the same base materialand alloy as specified for the fence framework. Aluminum gateframes may be assembled with corner fittings.4.3 Polymer-coa

6、ted steel or aluminum frame shall be poly-mer coated as specified for framework. Polymer-coated steelframes may be assembled with corner fittings. Welded jointsshall have suitable preventive coating applied to the welds.NOTE 1The word polymer is used to describe all types of heat setorganic exterior

7、 coatings and is not applicable to metallic coatings, suchas zinc or aluminum.5. Gate Frames, Fabric, Attachment, and Finish5.1 Gate Frames shall be of aluminum or steel tubing, roundor square, and assembled by means of corner fittings or welded,or formed by bending. The bend should be smooth andcon

8、tinuous.5.1.1 Corner Fitted and Welded Gates shall have verticaland horizontal interior members spaced so that no horizontaldimension between outside members shall be greater than 5 ft(1.524 m), and no vertical dimension between members shallbe greater than 5 ft (1.524 m).5.2 Fabric shall match that

9、 of the line fabric adjacent to thegate opening or as required by specifications or drawings, orboth. However, fabric having a breaking strength equivalent toor greater than the fabric used in the line of fence may be used.5.3 Attachment of Fabric to Gate FrameStretch the fabricso it is taut and fas

10、tened to frames by one of the followingmethods:5.3.1 Place a round rod or flat bar through the fabric andfasten with clips or bands, at a maximum spacing of 12 in. (305mm) on center, of sufficient strength to hold fabric taut betweenthe vertical frame members. Clips or bands shall conform tothe prof

11、ile of the frame members.5.3.2 Place a round rod or flat bar through the fabric andfasten with a J-bolt through the holes in the frame.5.3.3 Fasten all fabric to horizontal frame members and toany interior frame members by means of clips, tie wires, orbands suitable to retain the fabric to the frame

12、 members.Spacing should be at a maximum of 18 in. (450 mm) apart.6. Dimensions and Weights (of Gate Frames and GatePosts)6.1 Dimension (Height):6.1.1 The vertical dimension (height) of the gate should be2 in. (60 mm) less than the specified height of the adjacentfence.1This specification is under th

13、e jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved July 1, 2012. Published October 2012. Originallyapproved in 1980. Last previous edition approved in 2007 as F654 - 07. DOI:10.1520/F0

14、654-07R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive

15、, PO Box C700, West Conshohocken, PA 19428-2959. United States16.1.2 Where interior members are required, they shall beevenly spaced between outside members.6.2 Dimension (Width)Gate opening sizes are figured onthe inside dimensions between gate posts. The actual width ofthe gate panel shall be equa

16、l to the opening minus the spacerequired for free operation of hinges and latches.6.3 Diameter and Weight of Frames See Table 1.6.4 Gate Post Dimensions and Weights See Table 2 andTable 3.7. Gate Hardware7.1 All gate hardware shall be of sufficient strength anddurability to support the gate and repe

17、ated open-close cycles.7.2 Single and Double Gate Latches :7.2.1 Single Gate Latches shall be of lockable design.7.2.2 Double Gate Latches shall be equipped with a centerdrop rod or bar, and suitable fork or gravity latch to retain bothgates in a parallel position while closed, or a positive locking

18、device with suitable attachment to retain both gates in parallelposition while closed.7.3 Center Stops When required for drop rods or bars,center stops may be of manufactured design of aluminum orsteel and suitable for attachment to slab or installed in concreteor may be a hole drilled into existing

19、 concrete slab.7.4 Gate Holdbacks are optional to the purchaser.7.5 Accessories are optional as required by specifications,drawings, or to match the line adjacent to the gates.8. Workmanship8.1 Gates shall be produced in accordance with goodcommercial practices. Defects in welds, chain link fabric,b

20、racing and truss rods, and accessories shall be noted and, ifpresent to any considerable extent, shall provide a basis forrejection.9. Inspection9.1 The manufacturer shall afford the inspector representingthe purchaser all reasonable facilities to satisfy him that thematerial being furnished is in a

21、ccordance with this specifica-tion. Unless otherwise specified, all tests and inspection shallbe made at the place of manufacture, prior to shipment, andshall be so conducted as not to interfere unnecessarily with theoperation of the work.TABLE 1 Fence Frames (Minimum Requirements)Outside Dimension

22、Pipe,in. (mm)Wall Thickness,in. (mm)Nominal Weight,lb/ft (kg/m)Steel:Round tube 1.315 (33.4) 0.065 (1.65) 0.8681 (1.29)Square tube 1.25 by 1.25 (31.75 by 31.75) 0.065 (1.65) 1.05 (1.56)TABLE 2 Gate Posts (for Gate Leaf Width of 48 in. (1.219 m) or Less)Outside Dimension Pipe,in. (mm)Wall Thickness,i

23、n. (mm)Nominal Weight,lb/ft (kg/m)Round Post:Steel 1.90 (48.3) 0.065 (1.651) 1.274 (1.896)Square Post:Steel 2 by 2 (50.8 by 50.8) 0.080 (2.032) 2.09 (3.11)TABLE 3 Gate Posts (for Gate Leaf Width over 48 in. (1.201 m) to 72 in. (1.829 m)AOutside Dimension Pipe,in. (mm)Wall Thickness,in. (mm)Nominal W

24、eight,lb/ft (kg/m)Round Post:Steel 2.375 (60.3) 0.095 (2.93) 2.31 (3.44)Square Post:Steel 2.5 by 2.5 (63.5 by 63.5) 0.083 (2.11) 2.73 (4.06)AGate posts for gate leaf width up to 60 in. (1.524 m) may use a round steel post 2.375 in. (60.3 mm) in diameter with a wall thickness of 0.065 in. (1.651 mm).

25、F654 07 (2012)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of s

26、uch rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for add

27、itional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to t

28、he ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F654 07 (2012)3