ASTM F1007-1986(2007) Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application《套装滑动成型或船用管道膨胀节的标准规范》.pdf

《ASTM F1007-1986(2007) Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application《套装滑动成型或船用管道膨胀节的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F1007-1986(2007) Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application《套装滑动成型或船用管道膨胀节的标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 1007 86 (Reapproved 2007)An American National StandardStandard Specification forPipeline Expansion Joints of the Packed Slip Type forMarine Application1This standard is issued under the fixed designation F 1007; the number immediately following the designation indicates the year ofori

2、ginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the design, manufacturing, andtesti

3、ng of packed slip-type expansion joints used in pipelinesfor accommodating axial thermal growth or contraction fromthe pipeline carrying fluid.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2

4、.1 ASTM Standards:2A 53/A 53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and SeamlessA 216/A 216M Specification for Steel Castings, Carbon,Suitable for Fusion Welding, for High-Temperature Ser-viceA 285/A 285M Specification for Pressure Vessel Plates,Carbon Steel, Low-

5、and Intermediate-Tensile StrengthB 650 Specification for Electrodeposited Engineering Chro-mium Coatings on Ferrous Substrates2.2 ANSI Standards:3B16.5 Steel Pipe Flanges and Flanged FittingsB16.25 Buttwelding EndsB31.1 Power Piping2.3 ASME Standards:4Section V Nondestructive ExaminationSection VIII

6、, Division 1 Pressure VesselsSection IX Welding and Brazing Qualifications2.4 AISI Standard:C-1018 Carbon Steel53. Classification3.1 The expansion joints shall be of the following types,styles, classes, and forms:3.1.1 Type 1Injectable semiplastic packing type, designedfor injecting packing under fu

7、ll-line pressure.3.1.2 Style IInternally externally guided with guides inte-gral with stuffing box.3.1.3 Style IIInternally externally guided with guidesintegral with stuffing box and with low-friction inserts at theguide surfaces.3.1.4 Class ISingle joint, single slip.3.1.5 Class IIDouble joint, do

8、uble slip.3.1.6 Form IWeld end.3.1.7 Form IIFlanged end.3.1.8 Form IIIOther.4. Ordering Information4.1 Expansion joints shall meet all the requirements of thelatest issue of this specification. Where possible, the expansionjoint shall be the manufacturers standard commercial product.Additional or su

9、perior features that are not prohibited by thisspecification but which are a part of the manufacturersstandard product, shall be included with the expansion jointbeing offered. A standard commercial product is a product thathas been sold or is currently being offered for sale on thecommercial market

10、 through advertisements or manufacturerscatalogs, or brochures, and represents the latest productionmodel.4.2 Purchase order or inquiry for expansion joints to thisspecification shall specify the following:4.2.1 Title, number, and latest revision of this specification.4.2.2 Style, class, and form re

11、quired.4.2.3 Materials, other than standard as specified (see Section8).4.2.4 Service conditions shall specify the following:4.2.4.1 Maximum and minimum operating temperature(F).1This specification is under the jurisdiction of Committee F25 on Ships andMarine Technology and is the direct responsibil

12、ity of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Dec. 1, 2007. Published January 2008. Originallyapproved in 1986. Last previous edition approved in 2002 as F1007 - 86(2002).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custome

13、r Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from American S

14、ociety of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.5Available from American Iron and Steel Institute (AISI), 1140 ConnecticutAve., NW, Suite 705, Washington, DC 20036, http:/www.steel.org.1Copyright ASTM International,

15、100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.2.4.2 Maximum operating pressure (psig).4.2.4.3 Fluid handled.4.2.4.4 Corrosive conditions, if applicable.4.2.5 Total axial expansion or contraction.4.2.6 ANSI pressure class, facing, and drilling for flangedend jo

16、int and pipe schedule or wall thickness of ends for weldend joint.4.2.7 If base is required for support or main anchor on ClassI expansion joint.4.2.8 Drain connection, if required.4.2.9 Service connection if required, noting location andtype of connection.4.2.10 Slip protectors, if required.4.2.11

17、Adjustment rods for field extension or compressionof the slip if required.4.2.12 If hot-dip galvanizing of parts is required.4.2.13 Spare parts, accessories, and special tools, if re-quired.4.2.14 Hydrostatic testing and test pressure, if required.4.2.15 Radiographic or other nondestructive testing

18、of weldjoints if required.5. Materials and Manufacture5.1 Materials:5.1.1 Materials of construction shall conform to the require-ments as specified in this specification (see Section 8) and shallbe new and free from defects that would adversely affect theperformance of individual components or assem

19、blies.5.1.2 As specified in this specification and as required, theexpansion joint shall be provided with flanged or welded endconnections, limit stops, stuffing boxes with integral guides,base, drain connection, service connection, slip protectors, andadjustment rods.5.2 Manufacture:5.2.1 GeneralUn

20、less otherwise required by this specifi-cation, the manufacturers standard shop practices for thefabrication of the expansion joint is acceptable, provided thesepractices conform to the requirements and recommendations ofthis specification.5.2.2 All WeldingWelding procedure qualifications,welder per

21、formance qualification, welding materials, preheat,and postweld heat treatment if required, shall be in accordancewith ANSI B31.1 and ASME Code Section IX.5.2.3 IdentificationEach completed expansion joint shallhave a name plate made from a corrosion-resistant materialpermanently attached showing as

22、 a minimum the following:5.2.3.1 Manufacturers model number and joint size,5.2.3.2 Design pressure and design temperature range,5.2.3.3 Nominal traverse or movement per slip,5.2.3.4 Type of packing and service fluid, and5.2.3.5 Date of manufacture.6. Joint Descriptions6.1 Styles:6.1.1 Style IThe sli

23、p of the expansion joint shall be guidedwith the body of the expansion joint by internal and externalguides that are integral with the stuffing box. Semiplasticpacking shall be injected into the stuffing box and may becontained within the stuffing box chamber by ring-type pack-ing. All packing shall

24、 be of the self-lubricating type. Theexpansion joint and semiplastic packing shall be suitable forthe safe injection of the packing under full-line pressure to stopleakage. Provisions for packing injection shall be by deviceslocated radially about the stuffing box and designed to permita maximum eva

25、cuation of packing at the bottom of the packingdevice when the injector is fully engaged. The number ofdevices with injectors for each stuffing box shall be inaccordance with the manufacturers standard practice. Thedesign of the packing injection devices shall be such as toensure no blowback of inje

26、ctable packing or the service fluidwhen injecting packing under full-line pressure.6.1.2 Style IIThe expansion joint shall be the same asStyle I except low-friction corrosion-resistant material orinserts shall be used for internal and external guiding to preventslip scoring from pipe misalignment or

27、 vibration and to preventcorrosion of the guide surfaces.6.2 Classes:6.2.1 Class IThe expansion joint shall have slip at onlyone end of the joint. Class I expansion joints may or may notrequire a base.6.2.2 Class IIThe expansion joint shall have slip at bothends of the joint. Class II expansion join

28、ts shall require a base.6.3 Forms :6.3.1 Form IWelded End: The expansion joint shall haveprovisions at each end of the joint for field welding to theadjoining pipe line.6.3.2 Form IIFlanged End: The expansion joint shallhave flanges at each end of the joint for bolting to the matingflanges of the ad

29、joining pipe line.6.3.3 Form IIIThe expansion joint shall have other endconnections as specified for attaching to the adjoining pipeline.7. Design7.1 The expansion joint shall be designed to conform toapplicable sections of the latest edition of ANSI B31.1 andother applicable documents as noted in S

30、ection 2.7.2 Compresson ForceUnless otherwise specified, theforce to compress or extend the slip of the expansion joint shallnot exceed 1000 lbf/in. (175 100 N/m) of nominal pipediameter.8. Construction8.1 SlipThe slip shall be manufactured from steel pipeconforming to Specification A 53/A 53M, Grad

31、e B, or a rolledand welded cylinder from Specification A 285/A 285M, GradeC plate, or equal with the longitudinal weld seam 100 %radiographed. The minimal wall thickness of the pipe or rolledcylinder shall be equivalent to Schematic 80 pipe for all sizesto 14 in. (356 mm), inclusive and Schematic 60

32、 for sizes 16 to24 in. (406 to 610 mm) to preclude slip collapse as a result ofexternal loading of the injectable packing. Heavier wall pipemay be required for expansion joints subjected to pressuresabove 600 psig and for pipe sizes above 24-in. (610-mm)diameter.8.1.1 Chrome PlateThe slip of the exp

33、ansion joints shallbe chrome plated with engineering chrome in accordance withSpecification B 650, Class 50.F 1007 86 (2007)28.2 Stuffng BoxThe stuffing box with integral internal andexternal guides shall be machined from Specification A 53/A 53M, Grade B Pipe, or AISI C-1018 seamless tubing or cast

34、steel in accordance with A 216/A 216M, Grade WCB. A rolledand welded cylinder from Specification A 285/A 285M, GradeC plate, or equal may be used provided the longitudinal weldseam is 100 % radiograph examined in accordance with ANSIB31.1 and ASME Code Section V.8.3 Traverse ChamberThis chamber, als

35、o referred to asthe “E.J. Body,” shall be machined from Specification A 53/A 53M, Grade B seamless steel pipe having a wall thicknesssuitable for the design service conditions. A rolled and weldedcylinder from Specification A 285/A 285M, Grade C, or equalsteel plate of suitable thickness for the des

36、ign service condi-tions may also be used if the longitudinal weld seam is 100 %radiograph inspected to ANSI B31.1 and ASME Code SectionV.8.4 End ConnectionsThe end connections of the expan-sion joint (see Section 6) shall be flanged, weld end, combi-nation of both, or others as specified. Flanges sh

37、all conform toANSI B16.5 and be of the size, material, pressure class, andfacing specified. Weld ends shall be beveled for welding toconform to ANSI B16.25 and be of the size, material, andnominal wall thickness as specified for the mating pipe.8.4.1 Body End Connection for Class I Expansion Joints:

38、8.4.1.1 Form IWeld End: The reduction of the body sizeto the pipeline size shall be accomplished by a formedreduction of the traverse chamber (body) or by a reducer buttwelded to the traverse chamber (body) that meets the require-ments of ANSI B31.1 and the ASME Code Section VIII,Division 1.8.4.1.2

39、Form IIFlanged End: Forged flanges shall beattached to the body by butt welding only and shall be inaccordance with the requirements of ANSI B31.1 and theASME Code Section VIII, Division 1.8.5 Limit StopsLimit stops may be of the external orinternal type manufactured from a suitable material and de-

40、signed to withstand the full-line pressure thrust load in theevent of a pipeline anchor failure.8.6 Internal and External GuidesSee 8.2.8.6.1 Low-Friction Internal and External GuidesThelow-friction internal and external guides or inserts shall bemade from noncorrosive materials with appropriate dif

41、ferentialhardness to also prevent scoring or binding of the slip.8.7 Base:8.7.1 Expansion Joint Without a Service ConnectionWhen a base is specified for Class I expansion joints, the baseshall be designed for use as a main anchor. Class II expansionjoints shall have a base that is suitable as an int

42、ermediateanchor. The base shall be of cast or fabricated steel thatconforms to the applicable ASTM standard and shall besuitably attached to the joint and drilled in accordance with themanufacturers standard practice.8.7.2 Expansion Joint With a Service ConnectionClass Iand Class II expansion joints

43、 with a service connection shall beprovided with a main anchor base and all anchor loading data(forces and moments) shall be made available to the manufac-turer to assure adequate anchor design. The base shall be ofcast or fabricated steel that conforms to the applicable ASTMstandard and shall be su

44、itably attached to the joint and drilledin accordance with the manufacturers standard practice.8.8 Service ConnectionUnless otherwise specified, a ser-vice connection, when required, shall be the manufacturersstandard design and shall meet the applicable requirements ofthe ASTM, ANSI, and ASME Codes

45、. The service connectionshall be supplied with end connections as specified (see 8.5).8.9 Drain ConnectionWhen required, a drain connectionshall be attached to the body of the expansion joint and shall bethe manufacturers standard unless otherwise specified. Thedrain connection shall meet the requir

46、ements for fitting con-nections as specified in ANSI B31.1.8.10 PackingUnless otherwise specified, the packingshall be the manufacturers standard-type packing and shall besuitable for the specified service conditions.8.11 Other Materials of ConstructionWhere the expan-sion joint is to transfer corro

47、sive fluids, or be installed in acorrosive atmosphere, corrosive-resistant materials as specifiedmay be substituted for the carbon steel components, especiallythe sliding slip.9. Drawing Requirements Drawing Requirements9.1 DrawingsWhen specified, dimensional sketches ordrawings sufficiently detaile

48、d to describe the expansion joint tobe supplied, shall be submitted with bid proposals. Theinch-pound system of measurements shall be used to dimen-sion drawings. Drawings shall note that the design of thecomponents or products is in full compliance with this speci-fication.10. Cleaning and Surface

49、Preservation10.1 CleaningThe internal and external surfaces of theexpansion joint shall be cleaned of dirt, oil, grease, and otherforeign material using a suitable cleaning solvent. Extremecare shall be used to ensure the interior is free of any slag, steelchips, or other similar materials that could lodge between theslip and the body and score the slip surface.10.2 Surface PreservationUnless specified, no preserva-tion will be required on the internal surface of the expansionjoint. All external surfaces except the chrome-plated sli