ASTM F34-2013 Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials《柔性阻挡材料液体提取物试验池结构的标准实施规程》.pdf

《ASTM F34-2013 Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials《柔性阻挡材料液体提取物试验池结构的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F34-2013 Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials《柔性阻挡材料液体提取物试验池结构的标准实施规程》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F34 13Standard Practice forConstruction of Test Cell for Liquid Extraction of FlexibleBarrier Materials1This standard is issued under the fixed designation F34; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year

2、of last revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the construction of test cells whichmay be used for the extraction of components from flexible

3、barrier materials by suitable extracting liquids, including foodsand food simulating solvents.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered

4、standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Ref

5、erenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD4754 Test Method for Two-Sided Liquid Extraction ofPlastic Materials Using FDA Migration Cell2.2 AOAC International Methods of Analysis:Official Method 964.15 Extraction from Flexible BarrierMaterials32.3 Code of Federal Regu

6、lations, Title 214The followingregulations cite this standard:21CFR 176.170 (d)(3)21CFR 177.1330 (e)(4)21CFR 177.1360 (b)21CFR 177.1670 (b)Appendix VI (b) Cells for Migration Testing, Guidance forIndustry: Preparation of Premarket Submissions for FoodContact Substances: Chemistry Recommendations (20

7、07)3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 flexible for purpose of this practice, a term applyingonly to those flexible materials which can be inserted in the testcell without affecting their barrier properties.4. Summary of Preactice4.1 This test cell defines the surf

8、ace area of a flexible barrierstructure that may contribute extractable/leachable substancesto a packaged article. Although stainless steel and othermaterials are cited in the body of the practice, the test cell maybe constructed of any durable material that does not contributeto the extractable con

9、tent. The test cell should be evaluated forleaks after manufacture. It should be washed of manufacturingor milling fluids that may contribute to the extraction result.4.2 Both pure chemicals as well as food simulants may beused as extracting solvents. FDA regulations usually specifythe extracting fl

10、uid of choice, but other solvents may be chosenbased on known or expected effects on the exposed surface.1This practice is under the jurisdiction of ASTM Committee F02 on FlexibleBarrier Packaging and is the direct responsibility of Subcommittee F02.15 onChemical/Safety Properties.Current edition ap

11、proved April 1, 2013. Published June 2013. Originallyapproved in 1963. Last previous edition approved in 2007 as F34 02 (2007). DOI:10.1520/F0034-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStanda

12、rds volume information, refer to the standards Document Summary page onthe ASTM website.3This method is available through the Association of Official AnalyticalChemists, International, 481 North Frederick Ave., Suite 500, Gaithersburg, MD20877 or from the AOAC website at www.aoac.org.4Federal Regula

13、tions may be purchased from the U.S. Government PrintingOffice Bookstore, 710 North Capitol Street, N.W., Washington, D. C. or may bedownloaded from the internet. The website for the chemistry guidelines documentmay be found at:http:/www.fda.gov/Food/GuidanceComplianceRegulatoryInformation/GuidanceD

14、ocuments/FoodIngredientsandPackaging/ucm081818.htmCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.3 The extractable content is usually measured by gravi-metric analysis after evaporation of the extracting fluid, butother types of an

15、alysis may be performed if considered to beappropriate. Some methodologies are cited in the FDA regu-lations.4.4 Unless otherwise specified, the test cell is designed to beused at room temperature and ambient environmental condi-tions.5. Significance and Use5.1 Knowledge of extractives from flexible

16、 barrier materialsmay serve many useful purposes. A test cell constructed asdescribed in this practice may be used for obtaining such data.Another test cell has been found equivalent to the onedescribed in this practice. See the appendix for the source ofthe alternate cell.5.2 United States Federal

17、Regulations 21CFR 176.170(d)(3), 21CFR 177.1330 (e)(4), 21CFR 177.1360 (b), 21CFR177.1670 (b), and 21CFR Appendix VI (b) cite this standardpractice as the basis for determining the amount of extractablesfrom the surface of a package or multilayer film or modifiedpaper in contact with food. In some c

18、ases, it is the only practicedefined for this purpose. No alternative detail is given in theregulations for conducting extractions.5.3 Test Method D4754 is not an equivalent to this testmethod. It is for two-sided extraction of films having the samematerial on both of the exposed surfaces of the fil

19、m.6. Reagents and Materials6.1 Purity of ReagentsACS (American Chemical Society)reagent grade chemicals shall be used in all tests. Unlessotherwise indicated, it is intended that all reagents shallconform to the specifications of the Committee on AnalyticalReagents of the American Chemical Society,

20、where suchspecifications are available.5Other grades may be used, pro-vided it is first ascertained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determination. Good analytical practice suggests that ablank determination using the extracting so

21、lvent and a cell withno sample be run in conjunction with each series of determi-nations Other grades may be used, provided it is first ascer-tained that the reagent is of sufficiently high purity to permit itsuse without lessening the accuracy of the determination.6.2 Purity of WaterType IV water;

22、Specification D1193.6.3 n-Heptane, ACS reagent grade.7. Procedure7.1 Construction of Test Cell (Fig. 1, Fig. 2)Assemble asfollows:7.1.1 Two 8 by 1138 by18-in. (203 by 289 by 3.2-mm) No.316 stainless steel plates, degreased.7.1.2 One14 by 112-in. (6.4 by 38-mm) U-shaped virginTFE-fluorocarbon gasket,

23、 grooved on both sides as shown.7.1.3 Twelve14 by 1-in. (6.4 by 25.4-mm) stainless steelbolts with wing nuts.7.1.4 One14 by 1 by 8-in. (6.4 by 25.4 by 203-mm)TFE-fluorocarbon gasket plug tapered to provide a tight fit.7.1.5 Six18 by38 by 3-in. (6.4 by 9.5 by 76-mm) plates.NOTE 1The use of stainless

24、steel washers on the outside of each plate(7.1.1) may prevent the cells from leaking.7.2 Pre-Use Conditioning of Test Cell:7.2.1 Wash stainless steel plates and TFE-fluorocarbon gas-kets in aqueous surfactant solution. Rinse with reagent waterand dry at 122F (50C). Wash with n-heptane and redistille

25、dacetone.7.2.2 For new TFE-fluorocarbon gaskets, immerse inn-heptane overnight. Rinse gaskets with fresh n-heptane. Drygaskets at 122F (50C).7.3 Use of Test Cell:7.3.1 Place one stainless steel plate of the cell on a flatsurface with bolts protruding up through the holes in the plate.Place a prepunc

26、hed (Note 2) specimen (side to contact liquidup) on the plate with one edge of the specimen aligned with thebottom of the plate, two edges aligned with the sides of theplate, and the bolts passing through the prepunched holes.Place a TFE-fluorocarbon gasket on the specimen with theouter edges of the

27、 gasket aligned with the cell bottom andsides. If desired, place a second prepunched specimen (side tocontact liquid down) on top of the gasket. If only one specimensheet is used for the test, place an inert barrier sheet such asTFE-fluorocarbon or clean foil in place of the second speci-men. Place

28、a second stainless steel plate on top of the assembly.Place wing nuts on the bolts and tighten.NOTE 2Use the cell plate as a template and any suitable sharpinstrument to prepunch the specimen through the bolt holes in the plate.7.3.2 Preheat the assembly (including the TFE-fluorocarbongasket plug) t

29、o the test temperature and retighten the nuts sothat the assembly is liquid-tight. The assembly is ready to use.8. Keywords8.1 extractables; flexible barrier materials; food simulatingsolvents; test cells5Reagent Chemicals, American Chemical Society Specifications , AmericanChemical Society, Washing

30、ton, DC.F34132SI Equivalentsin. mm in. mm in. mm116 1.658 15.9 214 5718 3.234 19 3 7614 6.4 1 25.4 8 203932 7112 38 1138 28938 9.5FIG. 1 Test Cell AssemblyF34133APPENDIX(Nonmandatory Information)X1. AN ALTERNATE TEST CELL FOR LIQUID EXTRACTIONS OF FLEXIBLE BARRIER MATERIALSX1.1 An alternate test cel

31、l has been found to be useful forliquid extractions of flexible barrier materials.6X1.2 The test cell requires less solvent than the original celldescribed in this practice, and maintains an adequate testsurface area for extractions. Food and Drug Administration(FDA) laboratories have successfully u

32、sed this cell to performextraction studies of PETE films with both water and Miglyol8127(a fractionated coconut oil) over a temperature range from60 to 120C.8,9X1.3 Reference is made to this cell in the Guidance forIndustry: Preparation of Premarket Submissions for FoodContact Substances: Chemistry

33、Recommendations (2007).46The test cell is a compression migration cell originally designed at DowChemical Company. There is no manufacturer of these cell systems known to thecommittee. If you are aware of suppliers, please provide this information to ASTMInternational Headquarters. Your comments wil

34、l receive careful consideration at ameeting of the responsible technical committee,1which you may attend.7The sole source of supply of Miglyol 812 known to the committee at this timeis Sasol Germany, GmbH, Arthur-Imhausen-Str 92, 58453 Witten, Germany.Miglyol 812 may be purchased in North America fr

35、om Peter Cremer, 3117Southside Ave., Cincinnati, OH. Local suppliers may also be found through aninternet search. If you are aware of alternative suppliers, please provide thisinformation to ASTM International Headquarters. Your comments will receivecareful consideration at a meeting of the responsi

36、ble technical committee,1whichyou may attend.8Begley, Timothy H., and Hollifield, Henry C., “Food Packaging Made fromRecycled Polymers: Functional Barrier Considerations,” Chapter 36, Plastics,Rubber, and Paper Recycling: A Pragmatic Approach. ACS Symposium Series609, 1995, pp. 445475.9Piringer, O.,

37、 Begley, T.H., et al.,“ Migration from Food Packaging Containinga Functional Barrier: Mathematical and Experimental Evaluation,” J. Agr. and FoodChem., Vol 46, No. 4, 1998, pp. 15321538.SI Equivalentsin. mm in. mm in. mm18 3.2 1 25.4 714 18414 6.4 214 57 814 21038 9.5 578 149 1212 31758 15.9FIG. 2 R

38、ack for Holding Test CellsF34134ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof

39、infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this st

40、andard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your

41、 views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F34135