ASTM E2579-2011 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics《制备并架设表面燃烧特性评估所用木材产品样本的标准操作规程》.pdf

《ASTM E2579-2011 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics《制备并架设表面燃烧特性评估所用木材产品样本的标准操作规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM E2579-2011 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics《制备并架设表面燃烧特性评估所用木材产品样本的标准操作规程》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2579 11An American National StandardStandard Practice forSpecimen Preparation and Mounting of Wood Products toAssess Surface Burning Characteristics1This standard is issued under the fixed designation E2579; the number immediately following the designation indicates the year oforiginal

2、 adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes procedures for specimen prepa-ration and mo

3、unting when testing wood products to assessflames spread and smoke development as surface burningcharacteristics using Test Method E84.1.2 Testing is conducted with Test Method E84.1.3 This practice does not provide pass/fail criteria that canbe used as a regulatory tool.1.4 Use the values stated in

4、 inch-pound units as the stan-dard, in referee decisions. The values in the SI system of unitsare given in parentheses, for information only; see IEEE/ASTM SI-10 for further details.1.5 This fire standard cannot be used to provide quantitativemeasures.1.6 Fire testing of products and materials is in

5、herentlyhazardous, and adequate safeguards for personnel and propertyshall be employed in conducting these tests. Fire testinginvolves hazardous materials and equipment. This standardgives instructions on specimen preparation and mounting, butthe fire-test-response method is given in Test Method E84

6、. Seealso Section 10.1.7 The text of this standard references notes and footnoteswhich provide explanatory materials. These notes and foot-notes shall not be considered requirements of the standard.1.8 This standard does not purport to address all of thesafety concerns, if any, associated with its u

7、se. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C1396/C1396M Specification for Gypsum BoardD9 Terminology Relating to Wood

8、 and Wood-Based Prod-uctsD1038 Terminology Relating to Veneer and PlywoodD1554 Terminology Relating to Wood-Base Fiber and Par-ticle Panel MaterialsE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE176 Terminology of Fire StandardsIEEE/ASTM SI-10 International System of Units

9、(SI): TheModern Metric System2.2 CSA Standard:3CSA O121 Douglas Fir Plywood2.3 HPVA Standard:4ANSI/HPVA HP-1 American National Standard for Hard-wood and Decorative Plywood2.4 NIST Standard:5Voluntary Product Standard PS 1-07 Structural Plywood3. Terminology3.1 DefinitionsFor definitions of terms us

10、ed in this prac-tice refer to the terminology contained in Terminologies E176,D9, D1038, D1554, and ANSI/HPVA HP-1.4. Summary of Practice4.1 This practice describes procedures for specimen prepa-ration and mounting when testing wood products to assessflame spread and smoke development as surface bur

11、ningcharacteristics using Test Method E84.5. Significance and Use5.1 Solid board, lumber and timber products (includingsolid boards, lumber, timber, fingerjoined lumber, glulam,laminate wood, laminated veneer lumber and parallel strandlumber products); panel products (including fibreboard, hard-boar

12、d, oriented strandboard, waferboard and plywood panelproducts); decorative wood products and shingles and shakesused as interior wall and ceiling finish are often evaluated with1This practice is under the jurisdiction of ASTM Committee E05 on FireStandards and is the direct responsibility of Subcomm

13、ittee E05.22 on SurfaceBurning.Current edition approved Oct. 1, 2011. Published October 2011. Originallyapproved in 2007. Last previous edition approved in 2007 as E2579-07. DOI:10.1520/E2579-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at

14、serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Canadian Standards Association (CSA), 178 Rexdale Blvd.,Toronto, ON Canada M9W 1R3.4Available from the Hardwood Plywood and Veneer Association, 1825 M

15、ichaelFaraday Dr., Reston, VA 20190.5Available from National Institute of Standards and Technology (NIST), 100Bureau Dr., Stop 3460, Gaithersburg, MD 20899-3460.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Test Method E84 to compl

16、y with code requirements. Thispractice describes specimen preparation and mounting proce-dures for such materials and systems.5.2 If it can be demonstrated that none of the methodsdescribed in this practice are applicable to a particular product,other mounting methods shall be permitted to be used.

17、Thisinformation shall be included in the report.5.3 The limitations for this procedure are those associatedwith Test Method E84.6. Conditioning6.1 The test specimens shall be conditioned as described inthe section on specimen conditioning in Test Method E84.7. Test Specimens7.1 The test specimen siz

18、es shall comply with those de-scribed in the test specimen section of Test Method E84. Thetest specimens shall be butted against the vent end of the firetest chamber and shall consist of a continuous, unbrokenlength, or of sections joined or butted end-to-end. The testspecimens shall have a width of

19、 20 to 24 in. (510 to 610 mm),a length of 24 ft + 12 in. 6 in. (7.32 m + 305 mm 152 mm)and a maximum thickness of 4 in. (101 mm).7.2 Wood product test specimens shall be prepared asdescribed in Section 8.8. Test Specimen Preparation8.1 General:8.1.1 Wood products shall be representative of the mater

20、ialswhich the test is intended to examine.8.1.2 The preparation of test specimens of wood productstreated by pressure impregnation or by other means shall beidentical to that specified for untreated wood products.8.2 Solid Boards, Lumber, Timber, Fingerjoined Lumber,Glulam, Laminate Wood, Laminated

21、Veneer Lumber and Par-allel Strand Lumber Products:8.2.1 General construction outline for solid board, lumber,timber, fingerjoined lumber, glulam, laminate wood, laminatedveneer lumber and parallel strand lumber decks is shown inFig. 1.8.2.2 The thickness of the test material pieces shall berepresen

22、tative of the material which the test is intended toexamine.8.2.3 Batten strips shall be nominal 1 by316 in. (25 by 5mm) and shall be constructed of metal.8.2.4 Use either cement coated nails or No. 8, 10 or 12 woodscrews, two per solid board, lumber, timber, fingerjoinedlumber, glulam, laminate woo

23、d, laminated veneer lumber andparallel strand lumber piece per batten, and of sufficient lengthto penetrate through the battens and not less than 75 % of thetest material.8.2.5 For outside edges, use the longest lumber, timber,fingerjoined lumber, glulam, laminate wood laminated veneerlumber paralle

24、l strand lumber strips available. If shorter than96 in. (2.44 m), use 6 in. (152 mm) long batten strips. Do notuse lumber, timber, fingerjoined lumber, glulam, laminatewood, laminated veneer lumber, or parallel strand lumber stripsless than 24 in. (610 mm) long on outside edges.8.2.6 Allow 6 in. (15

25、2 mm) minimum distance betweenother joints on adjacent lumber, timber, fingerjoined lumber,glulam, laminate wood laminated veneer lumber parallel strandlumber strips.8.2.7 While fastening with nails or screws, use cabinetclamps or other suitable means to ensure there are no cracks, orgaps between th

26、e lumber, timber, fingerjoined lumber, glulam,laminate wood laminated veneer lumber parallel strand lumberstrips in the deck surface.8.2.8 Mount the specimens on the ledges of the Test MethodE84 furnace without using additional means of support.8.3 Panel Products with Suffcient Structural Integrity

27、toSupport Themselves:8.3.1 Panel products with sufficient structural integrity tosupport themselves shall be cut to the width of the fire testchamber, butted end-to-end, and mounted on the ledges of theTest Method E84 furnace without using additional means ofsupport.8.3.2 Panel products14 in. (6.3 m

28、m) or less in thickness notintended to be applied over gypsum board or a wood substrateshall be cut to the width of the fire test chamber, buttedend-to-end, and mounted on the ledges of the Test Method E84FIG. 1 General Construction Outline for Solid Board, Lumber, Timber, Fingerjoined Lumber, Glula

29、m, Laminate Wood, Laminated VeneerLumber and Parallel Strand Lumber DecksE2579 112furnace without additional means of support if they havesufficient integrity to support themselves within the test cham-ber without sagging116 in. (1.5 mm) or more when measuredat the centre-line of the test chamber.8.

30、4 Wood Veneers and Panel Products with InsuffcientStructural Integrity to Support Themselves:8.4.1 Wood veneers and panel products with insufficientstructural integrity to support themselves shall be cut to thewidth of the fire test chamber, butted end-to-end and supportedwithin the fire test chambe

31、r by steel rods not more than18 in.(3 mm) in diameter spanning the width of the tunnel. The rodsshall be placed approximately 2 in. (51-mm) from each end ofeach panel and at approximately 24 in. (610 mm) intervalsstarting with the fire end of each panel.8.4.2 Wood veneers and panel products18 in. (3

32、 mm) or lessin thickness not intended to be applied over gypsum board ora wood substrate, and with insufficient integrity to supportthemselves within the test chamber without sagging116 in. (1.5mm) or more when measured at the centre-line of the testchamber, shall be cut to the width of the fire tes

33、t chamber,butted end-to-end, and supported within the test chamber bysteel rods not more than14 in. (6.3 mm) in diameter spanningthe width of the tunnel. The rods shall be placed approximately2 in. (51 mm) from each end of each panel and at approxi-mately 24 in. (610 mm) intervals starting at the fi

34、re end of eachpanel.8.5 Wood Veneers and Panel Products Intended to beApplied over Gypsum Board:8.5.1 If the wood veneer or panel product is intended to beapplied over gypsum board, the specimens shall consist of theveneer or panel product mounted on58 in. (15.9 mm) Type Xthick gypsum board complyin

35、g with Specification C1396/C1396M. The gypsum board shall not be required to bemounted on studs or battens. Mount the specimens on theledges of the Test Method E84 furnace without using additionalmeans of support.8.5.2 The adhesive used to attach the veneer or panelproduct to the gypsum board shall

36、be that specified by themanufacturer and applied in accordance with manufacturerapplication instructions.8.6 Wood Veneers and Panel Products Intended to beApplied over a Wood Substrate:8.6.1 If the veneer or panel product is intended to be appliedover a wood substrate, the specimens shall consist of

37、 theveneer or panel product mounted on the “A” face of nominal1532 in. untreated plywood with a face veneer of Douglas fir.The plywood shall comply with NIST Voluntary ProductStandard PS 1-07. The plywood shall carry the grade stamp ofeither APA-The Engineered Wood Association6or TECO7,indicating th

38、at the plywood has been graded PS 1-07 A-C andis for exterior exposure. Alternatively, the plywood shall bepermitted to be stamped as conforming to CSA O121 (Stan-dard for Douglas fir plywood). Mount the specimens on theledges of the Test Method E84 furnace without using additionalmeans of support.8

39、.6.2 The adhesive used to attach the veneer or panelproduct to the wood substrate shall be that specified by themanufacturer and applied in accordance with manufacturersapplication instructions.8.7 Wood Shingles and Shakes:8.7.1 Wood shingles and shakes shall be mounted accordingto manufacturers ins

40、tructions on the “A” face of nominal1516in. panels of untreated plywood with a face veneer of Douglasfir and with the thicker butt ends of each shingle or shakeoriented towards one end of the plywood panel. The plywoodshall comply with NIST Voluntary Product Standard PS 1-07.The plywood shall carry

41、the grade stamp of either APA-TheEngineered Wood Association6or TECO7, indicating that theplywood has been graded PS 1-07 A-C and is for exteriorexposure. Alternatively, the plywood shall be permitted to bestamped as conforming to CSA O121 (Standard for Douglas firplywood).8.7.2 The specimens shall

42、be butted end-to end, with thethicker butt-ends of the shingles oriented towards the fire endof the furnace, and mounted on the ledges of the Test MethodE84 furnace without using additional means of support.8.7.3 If it can be demonstrated that the method described in8.7.1 of this practice is not app

43、licable to a particular type ofwood shingle or shake, another mounting method, based on themanufacturers installation instructions, shall be permitted tobe used. This information shall be included in the report.9. Testing of Specimens9.1 All testing shall be conducted using the methodologydescribed

44、in Test Method E84.10. Operator Safety10.1 The primary concerns for operator safety are associ-ated with the fire-test-response procedure, Test Method E84,and not with the specimen preparation procedure. Safetyrecommendations are included in Test Method E84.11. Report11.1 Report a detailed descripti

45、on of the system beingtested.11.2 Report a detailed description of the specimen prepara-tion method used, including any substrate or adhesive, if used,and its application rate, per Section 8.11.3 Report all the information required in the reportingsection of Test Method E84, including observations,

46、graphicalresults and the values of the flame spread index and of thesmoke developed index in each test.12. Keywords12.1 fibreboard; fingerjoined lumber; fire; fire test; flamespread; glulam; hardboard; laminate wood; laminated veneerlumber; lumber; oriented strandboard; parallel strand lumber;plywoo

47、d; shingles and shakes; smoke developed; solid boards;Steiner tunnel; timber; waferboard; wood products6Information available from APA, The Engineered Wood Association, 7011South 19th, Tacoma, WA, 98466.7Information available from TECO, 5650 Terra Court, Sun Prairie, WI, 53590.E2579 113ANNEXESA1. WO

48、OD PRODUCTS INTENDED TO BE APPLIED OVER GYPSUM BOARDA1.1 This practice specifies that wood products intended tobe applied over gypsum board be mounted over58 in. (15.9mm) thick Type X gypsum board complying with SpecificationC1396/C1396M. Test results, as calculated in Section 9 of TestMethod E84 an

49、d observations of the burning characteristics ofwood products mounted over58 in. (15.9 mm) thick Type Xgypsum board product are applicable to those for woodproducts on other gypsum board products not less than12 in.(12.7 mm) thick.A2. WOOD PRODUCTS INTENDED TO BE APPLIED OVER WOOD SUBSTRATESA2.1 This practice specifies that wood products intended tobe applied over wood substrates be mounted over the “A” faceof nominal1532 in. untreated plywood complying with NISTVoluntary Product Standard PS 1-07 and having a face veneerof Douglas fir. Test results, as calcul