ASTM E1694-1995a(2005) Standard Classification for Serviceability of an Office Facility for Special Facilities and Technologies《办公设备对特殊设备和技术的适用性标准分类》.pdf

《ASTM E1694-1995a(2005) Standard Classification for Serviceability of an Office Facility for Special Facilities and Technologies《办公设备对特殊设备和技术的适用性标准分类》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1694-1995a(2005) Standard Classification for Serviceability of an Office Facility for Special Facilities and Technologies《办公设备对特殊设备和技术的适用性标准分类》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E 1694 95a (Reapproved 2005)An American National StandardStandard Classification forServiceability of an Office Facility for Special Facilities andTechnologies1, 2This standard is issued under the fixed designation E 1694; the number immediately following the designation indicates the y

2、ear oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This classification covers pairs of scales for class

3、ifyingan aspect of the serviceability of an office facility, that is, thecapability of an office facility to meet certain possible require-ments for special facilities and technologies.1.2 Each pair of scales shown in Figs. 1-6 printed side-by-side on a page, are for classifying one topic of service

4、abilitywithin that aspect of serviceability. Each paragraph in anOccupant Requirement Scale (see Figs. 1-6) summarizes onelevel of serviceability on that topic that occupants mightrequire. The matching entry in the Facility Rating Scale (SeeFigs. 1-6) is a translation of the requirement into a descr

5、iptionof certain features of a facility that, taken in combination,indicate that the facility is likely to meet that level of requiredserviceability.1.3 The entries in the Facility Rating Scale (See Figs. 1-6)are indicative and not comprehensive. They are for quickscanning, to estimate approximately

6、, quickly, and economi-cally, how well an office facility is likely to meet the needs ofone or another type of occupant group over time. The entriesare not for measuring, knowing, and evaluating how an officefacility is performing.1.4 This classification can be used to estimate the level ofserviceab

7、ility of an existing facility. It can also be used toestimate the serviceability of a facility that has been plannedbut not yet built, such as one for which single-line drawingsand outline specifications have been prepared.1.5 This classification indicates what would cause a facilityto be rated at a

8、 certain level of serviceability, but it does notstate how to conduct a serviceability rating nor how to assigna serviceability score. That information is found in PracticeE 1334. The scales in this classification are complementary toand compatible with Practice E 1334. Each requires the other.2. Re

9、ferenced Documents2.1 ASTM Standards:3E 631 Terminology of Building ConstructionsE 1334 Practice for Rating Serviceability of a Building orBuilding-Related FacilityE 1679 Practice for Setting Requirements for Serviceabilityof a Building or Building-Related Facility2.2 ISO Documents:4ISO 6240 Interna

10、tional Standard, Performance Standards inBuildingContents and PresentationISO/DIS 7162 Draft International Standard, PerformanceStandards in BuildingContents and Format of Standardsfor Evaluation of PerformanceISO/DIS 7164 Draft International Standard, PerformanceStandards in BuildingDefinitions and

11、 Means of Expres-sion for the Performance of a Whole Building3. Terminology3.1 DefinitionsFor standard definitions of terms appli-cable to this classification, see Terminology E 631.3.1.1 facility, na physical setting used to serve a specificpurpose. (E 631)3.1.1.1 DiscussionA facility may be within

12、 a building, ora whole building, or a building with its sites and surroundingenvironment; or it may be a construction that is not a building.The term encompasses both the physical object and its use.3.1.2 facility serviceabilitythe capability of a facility toperform the function(s) for which it is d

13、esigned, used, orrequired to be used. (E 631)3.1.2.1 DiscussionThe scope of this performance is of thefacility as a system, including its subsystems, components, and1This classification is under the jurisdiction of ASTM Committee E06 onPerformance of Buildings and is the direct responsibility of Sub

14、committee E06.25on Whole Buildings and Facilities.Current edition approved May 1, 2005. Published May 2005. Originallyapproved in 1995. Last previous edition approved in 1999 as E 1694 95a (1999).2Portions of this document are based on material originally prepared by theInternational Centre for Faci

15、lities (ICF) and r 1993 by ICF and Minister of PublicWorks and Government Services Canada. Their cooperation in the development ofthis standard is acknowledged.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of

16、 ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428

17、-2959, United States.FIG. 1 Scale A.13.1 for Group or Shared Conference CenterE 1694 95a (2005)2materials and their interactions, such as acoustical, hydrother-mal, air purity, and economic; and of the relative importance ofeach performance requirement.3.1.3 offcea place, such as a room, suite, or b

18、uilding, inwhich business, clerical, or professional activities are con-ducted. (E 631)4. Significance and Use4.1 Each Facility Rating Scale in this classification providesa means for estimating the level of serviceability of a buildingFIG. 2 Scale A.13.2 for Video Teleconference FacilitiesE 1694 95

19、a (2005)3FIG. 3 Scale A.13.3 for Simultaneous TranslationE 1694 95a (2005)4or facility for one topic of serviceability, and for comparingthat level against the level of any other building or facility.4.2 This classification can be used for comparing how welldifferent buildings or facilities meet a p

20、articular requirementfor serviceability. It is applicable despite differences such aslocation, structure, mechanical systems, age, and buildingshape.4.3 This classification can be used to estimate the amount ofvariance of serviceability from target or from requirement, fora single office facility, o

21、r within a group of office facilities.4.4 This classification can be used to estimate the following:(1) serviceability of an existing facility for uses other than itspresent use; (2) the serviceability (potential) of a facility thathas been planned but not yet built; and (3) the serviceability(poten

22、tial) of a facility for which a remodelling has beenplanned.4.5 The use of this classification does not result in buildingevaluation or diagnosis. Building evaluation or diagnosisgenerally requires special expertise in building engineering ortechnology and the use of instruments, tools, or measureme

23、nts.FIG. 4 Scale A.13.4 for Satellite and Microwave LinksE 1694 95a (2005)54.6 This classification applies only to facilities that arebuilding constructions or parts thereof. (While this classifica-tion may be useful in rating the serviceability of facilities thatare not building constructions, such

24、 facilities are outside thescope of this classification.)FIG. 5 Scale A.13.5 for Mainframe Computer CenterE 1694 95a (2005)6FIG. 6 Scale A.13.6 for Telecommunications CenterE 1694 95a (2005)74.7 This classification is not intended for, and is not suitablefor, use for regulatory purposes, nor for fir

25、e hazard assessmentnor for fire risk assessment.5. Basis of Classification5.1 The scales shown in Figs. 1-6 contain the basis forclassification.5.2 Instructions for the use of this classification are con-tained in Practices E 1334 and E 1679.6. Keywords6.1 building; computer center; mainframe; confe

26、rence cen-ter; facility; facility occupants; function; microwave commu-nication; office; performance; rating; rating scale; require-ments; serviceability; simultaneous translation;telecommunications center; use; video teleconferenceASTM International takes no position respecting the validity of any

27、patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revis

28、ion at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your c

29、omments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrig

30、hted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).E 1694 95a (2005)8