ASTM E1404-1994(2013) Standard Specification for Laboratory Glass Conical Flasks《实验室玻璃锥形烧瓶的标准规范》.pdf

《ASTM E1404-1994(2013) Standard Specification for Laboratory Glass Conical Flasks《实验室玻璃锥形烧瓶的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM E1404-1994(2013) Standard Specification for Laboratory Glass Conical Flasks《实验室玻璃锥形烧瓶的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E1404 94 (Reapproved 2013)Standard Specification forLaboratory Glass Conical Flasks1This standard is issued under the fixed designation E1404; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides standard dimensional re-quirements for glass conical flasks suitable for general labora-tory use.NOTE 1Fo

3、r packaging standards, choose the following standards;E920, E921, and E1133.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.2. Referenced Documents2.1 ASTM Standards:2E438 Specification for Glasses in Laboratory ApparatusE67

4、1 Specification for Maximum Permissible Thermal Re-sidual Stress in Annealed Glass Laboratory ApparatusE675 Specification for Interchangeable Taper-Ground Stop-cocks And StoppersE676 Specification for Interchangeable Taper-Ground JointsE920 Specification for Commercially Packaged LaboratoryApparatus

5、E921 Specification for Export Packaged Laboratory Appa-ratusE1133 Practice for Performance Testing of Packaged Labo-ratory Apparatus for United States Government Procure-mentsE1157 Specification for Sampling and Testing of ReusableLaboratory Glassware3. Classification3.1 Conical flasks (Erlenmeyer)

6、shall be in in the followingtypes and capacities.3.1.1 Type Igeneral purpose, with graduated scale.3.1.1.1 Class 1Narrow mouth with heavy duty beadedtop, in capacities of 25 mL, 50 mL, 125 mL, 250 mL, 300 mL,500 mL, 1000 mL, 1500 mL, 2000 mL, 4000 mL, and 6000mL.3.1.1.2 Class 2Wide mouth with heavy

7、duty beaded top,in capacities of 125 mL, 250 mL, 500 mL, 1000 mL, and 2000mL.3.1.2 Type IITapered ground joint, with graduated scale.3.1.2.1 Class 1Outer Conical, joint without stopper, incapacities of 50 mL, 125 mL, 250 mL, 500 mL, 1000 mL, and2000 mL.3.1.2.2 Class 2with stopper, in capacities of 2

8、5 mL, 50mL, 125 mL, 250 mL, 500 mL, and 1000 mL.3.1.2.3 Class 3For iodine determination, in capacities of125 mL, 250 mL, and 500 mL.3.1.3 Type IIIScrew thread finish, with graduated scale, incapacities of 50 mL, 125 mL, 250 mL, 500 mL, 1000 mL, and2000 mL.3.1.4 Type IVCulture;3.1.4.1 Class 1Long nec

9、k, plain top, in capacities of 50mL, 125 mL, 250 mL, 500 mL, 1000 mL, and 2000 mL.3.1.4.2 Class 2Wide base (Fernbach), in capacity of 2800mL.3.1.4.3 Class 3Wide base, low form, in a capacity of 2500mL.NOTE 2The term milliliter (mL) is commonly used as a special namefor the cubic centimeter (cm3) and

10、 similarly the liter (L) for 1000 cubiccentimeters, in accordance with the International System of Units (SI).4. Material and Manufacturing4.1 Flasks shall be made of borosilicate glass conforming tothe requirements of Type I, Class A of Specification E438.4.2 Maximum residual thermal stress shall b

11、e such as toconform to Specification E671.5. Appearance5.1 The general appearance of the flasks shall be as illus-trated in Fig. 1.6. Design6.1 Conical flasks shall have flat bottoms. However, con-cavity in the bottom shall be permitted. The flask shall standvertically without rocking or spinning wh

12、en placed on a level1This specification is under the jurisdiction of ASTM Committee E41 onLaboratory Apparatus and is the direct responsibility of Subcommittee E41.01 onApparatus.Current edition approved Nov. 1, 2013. Published December 2013. Originallyapproved in 1991. Last previous edition approve

13、d in 2008 as E140494(2008). DOI:10.1520/E1404-94R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright

14、 ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1surface. Bottom heel radius shall be between 15 and 20 % ofthe maximum external diameter.6.2 Conical sides of the flask shall extend inwardly for thebottom and shall terminate in a short cylindri

15、cal neck.6.2.1 Type I and Type IV flasks shall have flask mouthfinished with a tooled, heavy duty bead.6.2.2 Type II, Class 1 shall have taper-ground joint neckfinish in accordance with Specification E676.6.2.3 Type II, Class 2 and Class 3 shall have taper-groundstopper neck finish to comply with E6

16、75. The Class 3 flasksshall also have a funnel neck flare. Stopper shall be tall enoughto facilitate removal from flask.6.2.4 Type III flasks shall have screw thread neck finish inaccordance with Glass Packaging Institute (G.P.I.) standardfinishes except as noted below. Dimensions shall be the samea

17、s Type I (Table 1).6.2.4.1 G.P.I. thread finishes shall be 24 to 410 for the 50and 125 mL sizes, 28 to 410 for the 250 mL size and 38 to 430for the 500, 1000 and 2000 mL sizes except that the 38 to 430may be modified to have the thread begin near the rim ratherthan approximately 0.55 in. below it.6.

18、3 Necks on all flasks shall be circular in cross-section. Topshall be tooled or beaded.FIG. 1 General Appearance of FlasksTABLE 1 Capacity and Dimensions For Type I and Type III Conical Flasks W/O Caps or StoppersCapacity, mLBody ODwidest point(maximum), mmOverall height(maximum), mmNeck-rubber stop

19、per fitWallthickness(minimum) mmMinimum graduatedrange mLMaximum graduatedsubdivisionmLClass 1 Class 225 42 67 0 . 0.9 10 to 25 550 52 83 1 . 0.9 20 to 50 10125 69 117 5 6 0.9 50 to 125 25250 84 138 6 8 0.9 50 to 200 25300 90 146 6 . 0.9 100 to 300 25500 105 186 7 10 1.0 100 to 500 501000 131 222 9

20、11 1.0 250 to 1000 501500 151 247 9 . 1.1 400 to 1400 1002000 166 282 10 13 1.1 600 to 2000 2004000 210 360 10 . 1.8 1000 to 4000 5006000 237 409 10 . 1.9 1500 to 6000 500E1404 94 (2013)27. Capacity and Dimensions7.1 Conical flasks shall conform to the requirements ofTable 1, Table 2, and Table 3.8.

21、 Sampling and Testing8.1 For sampling and testing refer to Specification E1157.9. Product Markings9.1 Each flask shall be permanently marked with the nameor known trademark of the manufacturer and the nominalcapacity. Flasks may also be marked with approximate gradu-ation markings that have a limit

22、of error of 65 % of fullcapacity. The graduation range and subdivision shall complywith the tables.9.2 There shall be an area on one side of the flask formarking with a pencil.10. Packaging10.1 For packaging, select from Specifications E920 orE921, or Practice E1133.11. Keywords11.1 conical; flasks;

23、 glassASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such right

24、s, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional s

25、tandardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM C

26、ommittee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the abovead

27、dress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 2 Capacity and Dimensions For Type II Conical Flasks Wit

28、hout StoppersACapacity, mLBody ODWidest Point(Max.) mmOverall Height (Max.) mm Neck FinishClass 1 Class 2 Class 3JointClass 1StopperClass 2SpecialClass 325 41 . 67 . . 16 .50 51 108 80 . 19/38 19 .125 69 136 121 127 24/40 22 22250 84 164 143 165 24/40 27 22500 105 203 182 202 24/40 32 221000 132 238

29、 210 . 24/40 32 .2000 166 292 . . 24/40 . .ASee Table 1 for wall thickness, minimum graduated range, and maximum graduated subdivision.TABLE 3 Capacity and Dimension For Type IV Conical FlasksWithout StoppersACapacity,mLBody ODwidestpoint(maximum)mmOverallheight(maximum)mmNominalneck ODmm Class1Neck-rubberstopper fitClasses 2and 3Wallthickness(minimum)mm50 51 107 18 . 0.8125 67 128 25 . 0.9250 84 143 38 . 0.9500 105 187 38 . 1.01000 131 234 38 . 1.02000 166 292 38 . 1.12500 260 205 . 6.5 1.52800 209 235 . 13 1.5ASee Table 1 for graduation range and subdivision if applicable.E1404 94 (2013)3