ASTM D7910-2014 9209 Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift《使用带电梯法收集表面真菌材料的标准实施规程》.pdf

《ASTM D7910-2014 9209 Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift《使用带电梯法收集表面真菌材料的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7910-2014 9209 Standard Practice for Collection of Fungal Material From Surfaces by Tape Lift《使用带电梯法收集表面真菌材料的标准实施规程》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7910 14Standard Practice forCollection of Fungal Material From Surfaces by Tape Lift1This standard is issued under the fixed designation D7910; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision

2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes the protocols for collection ofsurface samples using tape lifts and their delivery to thelaboratory.1.2 The

3、 purpose of this practice is to support the fieldinvestigator in differentiating fungal materials from non-fungalmaterial such as scuffs, soot deposits, stains, pigments, dust,efflorescence, adhesives, and water stains.1.3 The samples collected by this practice are appropriatefor either qualitative

4、or quantitative analysis by direct micros-copy.1.4 This practice does not address building occupantexposures, or occupant health risks.1.5 This practice does not address the development of aformal hypothesis or the establishment of sampling objectives.1.6 The values stated in SI units are to be rega

5、rded asstandard. No other units of measurement are included in thisstandard.1.7 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determi

6、ne the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D1356 Terminology Relating to Sampling and Analysis ofAtmospheresD4840 Guide for Sample Chain-of-Custody ProceduresD6044 Guide for Representative Sampling for Managementof Waste and Contaminated M

7、edia3. Terminology3.1 DefinitionsFor terminology not defined herein, referto Terminology D1356.3.2 Definitions of Terms Specific to This Standard:3.2.1 area (surface, sampled), na defined, measured ex-tent of surface sampled.3.2.2 chain of custody (COC), na document that providesfor the traceable tr

8、ansfer of field samples to the analyticallaboratory. It may or may not be combined with the field datasheet. D48403.2.3 direct microscopy analysis, nact of assessing micro-organisms (if present) using an optical compound microscope.3.2.4 field data sheet, na record of varying names thatprovides a re

9、ference document for information directly relatedto the sample collection event, including pre- and post-calibration data.3.2.5 fungal material, nfungal spores, hyphae, and repro-ductive structures.3.2.6 fungal structure (sing.), ncollective term for frag-ments or groups of fragments from fungi, inc

10、luding but notlimited to conidia, conidiophores, hyphae and spores.3.2.7 fungi (pl.), neukaryotic, heterotrophic, absorptiveorganisms that usually develop a rather diffuse, branched,tubular body (that is, network of hyphae) and usually repro-duce by means of spores.3The terms mold and mildew arefreq

11、uently used by laypersons when referring to various fungalcolonization.3.2.8 sample, na portion of material that is taken fortesting or record purposes. D60444. Significance and Use4.1 This practice defines a consistent procedure for collect-ing surface material using clear, transparent, single side

12、dadhesive collection medium, typically tape (also known as tapelift).4.2 A tape lift sample collected according to this practice isintended to be used to assess the material present at onespecific location on a surface for fungal content.1This practice is under the jurisdiction of ASTM Committee D22

13、 on Air Qualityand is the direct responsibility of Subcommittee D22.08 on Sampling and Analysisof Mold.Current edition approved June 1, 2014. Published July 2014. DOI: 10.1520/D7910-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceast

14、m.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Kendrick, B., The Fifth Kingdom, Focus Publishing / R. Pullins 6.6.2 Date, time, and signature of releasing party;6.6.3 Name and contact information of responsible party(that

15、is, investigators employer);6.6.4 Unique sample identifier(s);6.6.5 Contact information for analytical report receipt, ifdifferent than submitters information;6.6.6 Analysis requested; and6.6.7 Turn-around time(s) requested.6.7 Prepare samples for transport to the laboratory andsubmit to the laborat

16、ory as soon as practical following sam-pling.6.7.1 All samples should be packaged to protect fromdamage and temperature extremes during transit.6.7.2 Ship samples by way of a traceable carrier, if not handdelivered.7. Keywords7.1 fungal material; fungal particulate; fungi; fungus; indoorair quality;

17、 mold; mould; particulate; sampling; source sam-pling; spore; surface sampling; tape; tape liftD7910 142ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that

18、determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprove

19、d or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel

20、 that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual repri

21、nts (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 143