ASTM D7719-2013 red 7560 Standard Specification for High-Octane Unleaded Fuel《高辛烷值的无铅燃料的标准规范》.pdf

《ASTM D7719-2013 red 7560 Standard Specification for High-Octane Unleaded Fuel《高辛烷值的无铅燃料的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D7719-2013 red 7560 Standard Specification for High-Octane Unleaded Fuel《高辛烷值的无铅燃料的标准规范》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D7719 12D7719 13 An American National StandardStandard Specification forHigh Octane High-Octane Unleaded Test Fuel1This standard is issued under the fixed designation D7719; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis new test fuel specification is for a high-octane unleaded fuel to be used for gathering datatowar

3、d a commercial research report and specification on an unleaded high-octane aviation gasoline.A new high-octane unleaded test fuel has been developed which maintains the key performanceparameters of existing reciprocating aircraft engines. The two essential performance parameters ofMON and VP are in

4、versely related with respect to composition and thus can uniquely define acomposition range of the two components. The values for VP and MON in Table 1 reflect the limitingvalues of the two components. The binary fuel exhibits a higher volumetric energy density (net heatof combustion times density)

5、which is of great performance interest, although not explicitly stated inTable 1. The distillation parameters reflect the binary compositional effects. This is an unleaded fuel,so the limit of TEL in Table 1 is the same as is used in Specification D4814 for mogas and is meantto mitigate unintentiona

6、l contamination by TEL. Lastly, references to dyes remain in the specificationso that test groups may use them as necessary.1. Scope*1.1 This specification covers formulating specifications for purchases of a high octanehigh-octane (MON) unleaded test fuelunder contract and is intended solely for us

7、e by purchasing agencies for testing purposes.agencies.21.2 This specification defines a specific type of high octanehigh-octane (MON) unleaded test fuel for use as an aviationspark-ignition fuel. It does not include all fuels satisfactory for reciprocating aviation engines. Certain equipment or con

8、ditions ofuse may permit a wider, or require a narrower, range of characteristics than is shown by this specification.1.3 This specification, unless otherwise provided, prescribes the required properties of unleaded fuel at the time and place ofdelivery.1.4 The values stated in SI units are to be re

9、garded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and det

10、ermine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:3D86 Test Method for Distillation of Petroleum Products at Atmospheric PressureD130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip TestD323 Test Method for Vapor

11、Pressure of Petroleum Products (Reid Method)D873 Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method)D1094 Test Method for Water Reaction of Aviation FuelsD1266 Test Method for Sulfur in Petroleum Products (Lamp Method)1 This specification is under the jurisdiction of AST

12、M Committee D02 on Petroleum Products Products, Liquid Fuels, and Lubricants and is the direct responsibility ofSubcommittee D02.J0 on Aviation Fuels.Current edition approved June 1, 2012Dec. 1, 2013. Published August 2012January 2014. Originally approved in 2011. Last previous edition approved in 2

13、0112012 asD771911.D7719 12. DOI: 10.1520/D771912. 10.1520/D7719-13.2 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR:D02-1721.3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service a

14、t serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous ver

15、sion. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes sec

16、tion appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D1298 Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products byHydrometer MethodD2386 Test Met

17、hod for Freezing Point of Aviation FuelsD2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence SpectrometryD2624 Test Methods for Electrical Conductivity of Aviation and Distillate FuelsD2700 Test Method for Motor Octane Number of Spark-Ignition Engine FuelD32

18、37 Test Method for Lead in Gasoline by Atomic Absorption SpectroscopyD4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density MeterD4057 Practice for Manual Sampling of Petroleum and Petroleum ProductsD4171 Specification for Fuel System Icing InhibitorsD4177 Pra

19、ctice for Automatic Sampling of Petroleum and Petroleum ProductsD4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace ContaminationD4809 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)D4814 Specification for Automotive Sp

20、ark-Ignition Engine FuelD5006 Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation FuelsD5059 Test Methods for Lead in Gasoline by X-Ray SpectroscopyD5190 Test Method for Vapor Pressure of Petroleum Products (Automatic Method) (Withdrawn 2012)4D5191 Test Method for Va

21、por Pressure of Petroleum Products (Mini Method)E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications3. Terminology3.1 Definitions:3.1.1 aviation gasoline fuel, nfuel possessing specific properties suitable for operating aircraft powered by reciprocating

22、spark-ignition engines.3.1.2 binary, adjcharacterized by, or consisting of, two components.3.1.3 biomass, nbiological material including any material other than fossil fuels which is or was a living organism orcomponent or product of a living organism.3.1.4 high-octane, adjpossessing a motorMotor oc

23、tane number (MON) greater than 100.4. General4.1 This specification, unless otherwise provided, prescribes the required properties of a binary aviation fuel at the time andplace of delivery.5. Classification5.1 One grade of high octane high-octane unleaded test fuel is provided, known as UL102.6. Ma

24、terials and Manufacture6.1 High octane High-octane unleaded test fuel, except as otherwise specified in this specification, shall consist of blends ofrefined reformate hydrocarbons. The sources for these hydrocarbons include biomass, natural gas, or crude petroleum.6.1.1 See Appendix X1 for one part

25、icular composition being test that meets the parameters of Table 1.6.2 AdditivesThese can be added to each grade of high-octane unleaded aviation fuel in the amount, and of the composition,specified in the following list of approved materials:6.2.1 DyesThe total maximum concentration of dye in the f

26、uel is 6.0 mg/L.6.2.1.1 The only blue dye present in the finished fuel shall be essentially 1,4-dialkylaminoanthraquinone.6.2.1.2 The only yellow dyes in the finished fuel shall be essentially p-diethylaminoazobenzene (Color Index No. 11021) or1,3-benzenediol 2,4-bis (alkylphenyl)azo-.6.2.1.3 The on

27、ly red dye present in the finished fuel shall be essentially alkyl derivatives of azobenzene-4-azo-2-naphthol.6.2.1.4 The only orange dye present in the finished fuel shall be essentially benzene-azo-2-napthol (Color Index No. 12055).6.2.2 Other AdditivesThese may be added in the amount and of the c

28、omposition specified in the following list of approvedmaterials. The quantities and types shall be declared by the manufacturer.Additives added after the point of manufacture shall alsobe declared.6.2.2.1 AntioxidantsThe following oxidation inhibitors may be added to the fuel separately, or in combi

29、nation, in totalconcentration not to exceed 12 mg of inhibitor (not including weight of solvent) per litre of fuel.(1) 2,6-ditertiary butyl-4-methylphenol.(2) 2,4-dimethyl-6-tertiary butylphenol.4 The last approved version of this historical standard is referenced on www.astm.org.D7719 132(3) 2,6-di

30、tertiary butylphenol.(4) 75 % minimum 2,6-ditertiary butylphenol plus 25 % maximum mixed tertiary and tritertiary butylphenols.(5) 75 % minimum di- and tri-isopropyl phenols plus 25 % maximum di- and tri-tertiary butylphenols.(6) 72 % minimum 2,4-dimethyl-6-tertiary butylphenol plus 28 % maximum mon

31、omethyl and dimethyl tertiary butylphenols.(7) N,N-di-isopropyl-para-phenylenediamine.(8) N,N-di-secondary-butyl-para-phenylenediamine.6.2.2.2 Fuel System Icing Inhibitor (FSII)One of the following materials may be used:(1) Isopropyl Alcohol (IPA, propan-2-ol), in accordance with the requirements of

32、 Specification D4171 (Type II). May be usedin concentrations recommended by the aircraft manufacturer when required by the aircraft owner/operator.(2) Di-Ethylene Glycol Monomethyl Ether (Di-EGME), conforming to the requirements of Specification D4171 (Type III).May be used in concentrations of 0.10

33、 to 0.15 volume % when required by the aircraft owner/operator.(3) Test Method D5006 can be used to determine the concentration of Di-EGME in aviation fuels.NOTE 1Addition of isopropyl alcohol (IPA) may reduce knock ratings below minimum specification values.6.2.2.3 Electrical Conductivity AdditiveS

34、tadis 450 in concentrations up to 3 mg/Lis permitted. When loss of fuel conductivitynecessitates retreatment with electrical conductivity additive, further addition is permissible6.2.2.4 Corrosion Inhibitor AdditiveThe following corrosion inhibitors may be added to the fuel in concentrations not toe

35、xceed the maximum allowable concentration (MAC) listed for each additive.DCI-4A MAC = 24.0 g/m3DCI-6A MAC = 15.0 g/m3HITEC 580 MAC = 22.5 g/m3NALCO 5403 MAC = 22.5 g/m3NALCO 5405 MAC = 11.0 g/m3UNICOR J MAC = 22.5 g/m3SPEC-AID 8Q22 MAC = 24.0 g/m3TOLAD 351 MAC = 24.0 g/m3TOLAD 4410 MAC = 22.5 g/m37.

36、 Detailed Requirements7.1 The high octane high-octane unleaded test fuel shall conform to the requirements prescribed in Table 1.7.2 Test results shall not exceed the maximum or be less than the minimum values specified in Table 1. No allowance shall bemade for the precision of the test methods. To

37、determine the conformance to the specification requirement, a test result may berounded to the same number of significant figures as in Table 1 using Practice E29. Where multiple determinations are made, theaverage result, rounded according to Practice E29, shall be used.TABLE 1 Detailed Requirement

38、s for High Octane High-Octane Unleaded Test FuelOctane Ratings Grade UL102 ASTM Test MethodKnock value, Motor Octane Number min 102.2 D2700Density at 15C, kg/m3 min 790 D1298 or D4052max 825Distillation D86Initial boiling point, C Report D86Fuel Evaporated D8610 volume % at C max 75 D8640 volume % a

39、t C min 75 D8650 volume % at C max 165 D8690 volume % at C max 165 D86Final boiling point, C max 180 D86Sum of 10 % + 50 % evaporatedtemperatures, Cmin 135 D86Recovery, volume % min 97 D86Residue, volume % max 1.5 D86Loss, volume % max 1.5 D86Vapor pressure, 37.8C, kPa min 38.0 D323, D5190 , or D519

40、1max 49.0Freezing point, C max -58 D2386Sulfur, mass % max 0.05 D1266 or D2622Net heat of combustion, MJ/kg min 41.5 D4809Corrosion, copper strip, 2 h at 100C max No. 1 D130Oxidation stability (5 h aging) D873Potential gum, mg/100 mL max 6Water reaction D1094Volume change, mL max 2Electrical conduct

41、ivity, pS/m max 450 D2624Tetraethyl Lead, g Pb/L max 0.013 D3237 or D5059D7719 1338. Workmanship, Finish, and Appearance8.1 The high octane high-octane unleaded test fuel specified in this specification shall be free from undissolved water, sediment,and suspended matter. No substances of known dange

42、rous toxicity, under usual conditions of handling and use, shall be presentexcept as permitted in this specification.9. Sampling9.1 Because of the importance of proper sampling procedures in establishing fuel quality, use the appropriate procedures inPractice D4057 or Practice D4177.9.1.1 Although a

43、utomatic sampling following Practice D4177 may be useful in certain situations, initial manufacturer/supplierspecification compliance testing shall be performed on a sample taken following procedures in Practice D4057.9.2 A number of high octane high-octane unleaded test fuel properties, including c

44、opper corrosion, electrical conductivity, andothers are very sensitive to trace contamination which can originate from sample containers. For recommended sample containers,refer to Practice D4306.10. Reports10.1 The type and number of reports to ensure conformance with the requirements of this speci

45、fication shall be mutually agreedto by the purchaser and the supplier of the high octane high-octane unleaded test fuel.11. Test Methods11.1 The requirements enumerated in this specification shall be determined in accordance with the following ASTM testmethods:11.1.1 Knock Value (Lean Rating)Test Me

46、thod D2700.11.1.2 Tetraethyl LeadTest Methods D3237 or D5059.11.1.3 DensityTest Methods D1298 or D4052.11.1.4 DistillationTest Method D86.11.1.5 Freezing PointTest Method D2386.11.1.6 Vapor PressureTest Methods D323, D5190, or D5191.11.1.7 Net Heat of CombustionTest Method D4809.11.1.8 SulfurTest Me

47、thods D1266 or D2622.11.1.9 Corrosion (Copper Strip)Test Method D130, 2 h test at 100C in bomb.11.1.10 Potential Gum and Visible Lead PrecipitateTest Method D873 except that wherever the letter X occurs (referring tooxidation time) insert the number 5, designating the number of hours prescribed in t

48、his specification.11.1.11 Water ReactionTest Method D1094.11.1.12 Electrical ConductivityTest Method D2624.12. Keywords12.1 aviation fuel; binary; high-octane; unleadedAPPENDIX(Nonmandatory Information)X1. BINARY FUEL COMPOSITIONX1.1 IntroductionX1.1.1 A new high-octane unleaded fuel has been develo

49、ped for reciprocating aircraft engines. The two essential performanceparameters of MON and VP are inversely related with respect to composition and thus can uniquely define a composition rangeof the two components. The values for VP and MON in Table 1 reflect the limiting values of the two components. The binary fuelexhibits a higher volumetric energy density (net heat of combustion times density) which is of great performance interest, althoughnot explicitly stated in Table 1This . The distillation parameters reflect the binary composi