ASTM D7467-2015a red 5403 Standard Specification for Diesel Fuel Oil Biodiesel Blend (B6 to B20)《柴油燃料油 生物柴油混合燃料 (B6至B20) 的标准规格》.pdf
《ASTM D7467-2015a red 5403 Standard Specification for Diesel Fuel Oil Biodiesel Blend (B6 to B20)《柴油燃料油 生物柴油混合燃料 (B6至B20) 的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM D7467-2015a red 5403 Standard Specification for Diesel Fuel Oil Biodiesel Blend (B6 to B20)《柴油燃料油 生物柴油混合燃料 (B6至B20) 的标准规格》.pdf(23页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D7467 151D7467 15aStandard Specification forDiesel Fuel Oil, Biodiesel Blend (B6 to B20)1This standard is issued under the fixed designation D7467; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revis
2、ion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1 NOTEFootnotes A and B of Table 1 were corrected editorially in April 2015.1. Scope*1.1 This specification covers fuel blend grades of 6 vo
3、lume percent to 20 volume percent (%) biodiesel with the remainder beinga light middle or middle distillate diesel fuel, collectively designated as B6 to B20. These grades are suitable for various types ofdiesel engines.1.1.1 The biodiesel component of the blend shall conform to the requirements of
4、Specification D6751. The remainder of the fuelshall be a light middle or middle distillate grade diesel fuel conforming to Specification D975 grades No. 1-D and No. 2-D of anysulfur level specified with the following exceptions. The light middle or middle distillate grade diesel fuel whose sulfur le
5、vel,aromatic level, cetane, or lubricity falls outside of Specification D975 may be blended with biodiesel meeting Specification D6751,provided the finished mixtures meets this specification.1.1.2 The fuel sulfur grades are described as follows:1.1.2.1 Grade B6 to B20 S15A fuel with a maximum of 15
6、ppm 15 ppm sulfur.1.1.2.2 Grade B6 to B20 S500A fuel with a maximum of 500 ppm 500 ppm sulfur.1.1.2.3 Grade B6 to B20 S5000A fuel with a maximum of 5000 ppm 5000 ppm sulfur.1.2 This specification prescribes the required properties of B6 to B20 biodiesel blends at the time and place of delivery. Thes
7、pecification requirements may be applied at other points in the production and distribution system when provided by agreementbetween the purchaser and the supplier.1.2.1 Nothing in this specification shall preclude observance of federal, state, or local regulations that may be more restrictive.NOTE
8、1The generation and dissipation of static electricity can create problems in the handling of distillate diesel fuel oils. For more information onthis subject, see Guide D4865.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard
9、.2. Referenced Documents2.1 ASTM Standards:2D56 Test Method for Flash Point by Tag Closed Cup TesterD86 Test Method for Distillation of Petroleum Products at Atmospheric PressureD93 Test Methods for Flash Point by Pensky-Martens Closed Cup TesterD129 Test Method for Sulfur in Petroleum Products (Gen
10、eral High Pressure Decomposition Device Method)D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip TestD445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)D482 Test Method for Ash from Petroleum ProductsD52
11、4 Test Method for Ramsbottom Carbon Residue of Petroleum ProductsD613 Test Method for Cetane Number of Diesel Fuel OilD664 Test Method for Acid Number of Petroleum Products by Potentiometric TitrationD975 Specification for Diesel Fuel OilsD976 Test Method for Calculated Cetane Index of Distillate Fu
12、elsD1266 Test Method for Sulfur in Petroleum Products (Lamp Method)1 This specification is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of SubcommitteeD02.E0 on Burner, Diesel, Non-Aviation Gas Turbine, and Marine Fu
13、els.Current edition approved Jan. 1, 2015June 1, 2015. Published February 2015June 2015. Originally approved in 2008. Last previous edition approved in 20132015 asD7467 14.D7467 151. DOI: 10.1520/D7467-15E01.10.1520/D7467-15A.2 For referencedASTM standards, visit theASTM website, www.astm.org, or co
14、ntactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have b
15、een made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official docume
16、nt.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D1319 Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator AdsorptionD1552 Test Met
17、hod for Sulfur in Petroleum Products by High Temperature Combustion and IR DetectionD2500 Test Method for Cloud Point of Petroleum ProductsD2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence SpectrometryD2709 Test Method for Water and Sediment in Middle Dis
18、tillate Fuels by CentrifugeD2880 Specification for Gas Turbine Fuel OilsD3117 Test Method for Wax Appearance Point of Distillate Fuels (Withdrawn 2010)3D3120 Test Method for Trace Quantities of Sulfur in Light Liquid Petroleum Hydrocarbons by Oxidative MicrocoulometryD3828 Test Methods for Flash Poi
19、nt by Small Scale Closed Cup Tester3 The last approved version of this historical standard is referenced on www.astm.org.TABLE 1 Detailed Requirements for B6 to B20 Biodiesel BlendsProperty Test Method GradeB6 to B20 S15 B6 to B20 S500A B6 to B20 S5000BAcid Number, mg KOH/g, max D664 0.3 0.3 0.3Visc
20、osity, mm2/s at 40 C D445 1.9-4.1C 1.9-4.1C 1.9- 4.1CFlash Point, C, min D93 52D 52D 52DCloud Point, C, max or LTFT/CFPP, C, maxD2500, D4539, D6371 E E ESulfur Content, (g/g) D5453 15 . .mass percent, max D2622 . 0.05 .mass percen, max D129 . . 0.50mass percent, max D129 . . 0.50Distillation Tempera
21、ture, C,90 % vol recovered, maxD86 343 343 343Ramsbottom Carbon Residueon 10 % bottoms, mass %, maxD524 0.35 0.35 0.35Cetane Number, min D613F 40G 40G 40GOne of the following must bemet:(1) Cetane index, min.D976-80H 40 40 40(2) Aromaticity, volumepercent, maxD1319-03H 35 35 .Ash Content, mass perce
22、nt,maxD482 0.01 0.01 0.01Water and Sediment, volumepercent, maxD2709 0.05 0.05 0.05Copper Corrosion, 3 h at 50 C,maxD130 No. 3 No. 3 No. 3Biodiesel Content, % (V/V) D7371 6. - 20. 6. - 20. 6. - 20.Oxidation Stability, hours, min EN 15751 6 6 6Lubricity, HFRR at 60 C, mi-cron (m), maxD6079 520I 520I
23、520IA Under United States of America regulations, if Grades B6-20 S500 are sold for tax exempt purposes then, at, or beyond terminal storage tanks, they are required by 26CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectrally equivalent to 3.9 lb of the solid dye standard Solve
24、nt Red 26 per thousand barrels of dieselfuel or kerosine, or the tax must be collected.B Under United States of America regulations, Grades B6-20 S5000 are required by 40 CFR part 80 to contain a sufficient amount of the dye Solvent Red 164 so itspresence is visually apparent. At or beyond terminal
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD74672015ARED5403STANDARDSPECIFICATIONFORDIESELFUELOILBIODIESELBLENDB6TOB20 柴油 燃料油 生物 混合 燃料 B6 B20

链接地址:http://www.mydoc123.com/p-525567.html