ASTM D4991-2007 Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method《用真空法进行空瓶罐泄漏试验的标准试验方法》.pdf

《ASTM D4991-2007 Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method《用真空法进行空瓶罐泄漏试验的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4991-2007 Standard Test Method for Leakage Testing of Empty Rigid Containers by Vacuum Method《用真空法进行空瓶罐泄漏试验的标准试验方法》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 4991 07Standard Test Method forLeakage Testing of Empty Rigid Containers by VacuumMethod1This standard is issued under the fixed designation D 4991; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the testing of empty containersfor resistance to leakage under differential pressure conditionssuch

3、as those which can occur during air transport. It is suitablefor testing rigid containers intended for the transportation ofsome hazardous liquids in accordance with the United NationsRecommendations On The Transport Of Dangerous Goods(UN TDG) and the International Civil Aviation OrganizationTechnic

4、al Instructions For The Safe Transport Of DangerousGoods By Air (ICAO TIs).1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determin

5、e the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 996 Terminology of Packaging and Distribution Environ-mentsD 3078 Test Method for Determination of Leaks in FlexiblePackaging by Bubble Emission2.2 United Nations Document:ST/SG/AC.10/1 Recommend

6、ations On The Transport OfDangerous Goods32.3 International Civil Aviation Organization:DOC 9284-AN/905 Technical Instructions For The SafeTransport Of Dangerous Goods By Air43. Terminology3.1 Definitions: Terms and definitions used in this testmethod may be found in Terminology D 996.3.2 Definition

7、s of Terms Specific to This Standard:3.2.1 rigid containera container sufficiently rigid thatunder a positive pressure of 100-kPa gage the volumetricexpansion does not exceed 0.5 %, such as a glass bottle.4. Summary of Test Method4.1 An empty rigid container to be tested is pressurized byimmersion i

8、n an ethylene glycol-water solution in a transparenttest chamber and subjected to a gradually increasing partialvacuum. The container is observed for signs of leakage, asevidenced by escaping air bubbles during depressurization orfluid in the container after re-pressurization.5. Significance and Use

9、5.1 Containers may be pressurized in accordance with thistest method without modification to the closure or to the bodyof the container. This test method may be used for testing rigidcontainers intended for the transportation of some liquids by airin accordance with the ICAO TIs or in accordance wit

10、h the UNTDG.5.2 This test method establishes the point at which leakagecommences, with a limit of approximately 95-kPa (13.8-psi)differential. See Test Method D 3078 for flexible packages.5.3 This test method may not be suitable for some packages,such as packages with paper cap seals, where the test

11、 fluid mayrapidly deteriorate the packaging.6. Apparatus6.1 Transparent Vessel, large enough to permit the testspecimen(s) to be immersed in the test fluid with a minimumheadspace of 20 %, capable of withstanding at least 112-atmpressure differential, fitted with a flat vacuum-tight cover isrequired

12、.6.2 Vacuum Gage, Inlet Tube from a Source of Vacuum, andOutlet Tube to the Atmosphere, shall be sealed into the cover.The inlet and outlet tubes shall be equipped with handoperatedvalves. The vacuum gage shall be laboratory quality with afull-scale range from 0 to 100 kPa (0 to 14.5 psi) withminimu

13、m graduations no greater than 2 kPa (0.3 psi) andaccuracy to within 1 %. A suitable moisture trap, to preventback-flow of liquid, should be fitted between the vacuum gageand the source of vacuum.1This test method is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsib

14、ility of Subcommittee D10.23 on NaturalEnvironment Test Methods.Current edition approved April 1, 2007. Published April 2007. Originallyapproved in 1994. Last previous edition approved in 1999 as D 4991 94 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Cu

15、stomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from United Nations Sales Section, United Nations, New York, NY10017.4Available from Intereg Group, Inc., 5724 N. Pulaski Rd., Chicago, I

16、L 60646.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.3 Solution of Ethylene Glycol in Water, 50 % by Volumefor use as a test fluid, at ambient temperature unless otherwisespecified, is required. Where a test temperature other th

17、anambient is specified, the solution shall be at the specified testtemperature. Other solutions may be required for high and lowtemperatures.NOTE 1If ethylene glycol antifreeze solution is used, it should beclarified by filtering through activated charcoal.6.4 A suitable means to hold the test speci

18、men(s) with theclosure(s) not more than 25 mm (1 in.) under the surface of thetest fluid is required. The method of restraint should not affectthe results of the test.7. Test Specimens7.1 Test specimens shall consist of containers, includingtheir closures. Test specimens of containers which are inpr

19、oduction shall be representative samples, taken at random.7.2 Containers shall be empty containers which previouslycontained any substance and were cleaned of the contents priorto testing. New containers and closures, where available,should be used.7.3 Each container shall be closed for testing in t

20、he samemanner as it would be closed for actual shipment. All closuresshall be installed using the techniques or torques specified bythe closure manufacturer, container manufacturer, or shipper.Close containers at ambient pressure and temperature.7.4 Where a test temperature other than ambient is spe

21、cified,the sample containers shall be conditioned at the test tempera-ture for at least 24 h, and until they reach equilibrium oftemperature with the conditioning atmosphere.7.5 Unless otherwise specified, test at least three specimens.8. Preparation of Apparatus8.1 Assemble the apparatus in accorda

22、nce with Fig. 1.8.2 Prior to testing, draw a vacuum to at least 95-kPa(13.8-psi) differential and maintain this vacuum for 10 min inorder to remove air dissolved in the test fluid.9. Procedure9.1 Immerse the test specimens in the ethylene glycol-watersolution inside the transparent test chamber. Rem

23、ove as manybubbles as possible from the outer surface of the test specimensby agitation or other means.9.1.1 More than one specimen can be tested at one timeprovided that there is sufficient space in the test chamber toallow clear observation of each specimen. If this is done, affixthe test specimen

24、s so closures are sufficiently separated topermit individual observation of each, to detect leakage.9.2 Seal the lid, open the hand valve on the inlet tube, andclose the hand valve on the outlet tube to the atmosphere. Turnon the vacuum so that the gage rises slowly (from 30 s to 1min) to a pressure

25、 differential of 95 kPa (13.8 psi), or otherspecified pressure differential. The vacuum can be controlledby cracking open the hand valve on the outlet tube. During therise in vacuum, observe the test specimen(s) for leakage asevidenced by a continuous stream or recurring succession ofsmall bubbles.

26、Isolated bubbles caused by trapped air are notconsidered evidence of leakage. Maintain the vacuum for aminimum of 10 min. For test specimens which are singlepackagings or combination packagings in whole or part ofplastic material, maintain the vacuum for 30 min. Then turn thevacuum off and release i

27、t slowly by opening the hand valve onthe outlet tube. Keep the test specimen(s) immersed for at least30 s at ambient pressure. Remove the test specimen(s) andexamine the inside for fluid.9.3 Leakage is indicated by a continuous stream or recurringsuccession of bubbles. Fluid within the test specimen

28、 is alsoevidence of leakage.10. Report10.1 Report the following information:10.1.1 Identification of the containers and closures, usingmanufacturers part numbers and descriptions or using ex-ploded view drawings or cross-sectional drawings, includingdetailed data on material construction,10.1.2 Tota

29、l number of specimens tested,10.1.3 Number of specimens tested at one time,10.1.4 Test pressure requirement, where applicable,10.1.5 Whether test was performed at ambient temperatureand if not, the test temperature. If a test solution other than50 % ethylene glycol was used, identify the solution,10

30、.1.6 Whether test specimens passed or failed the test,where applicable,10.1.7 Whether each test specimen leaked and at whatpressure differential,10.1.8 Whether test fluid was apparent in each test specimenafter testing,10.1.9 A statement to the effect that all tests were made infull compliance with

31、the requirements of this test method, ornoting any variations and detailing them, and10.1.10 The name and address of the testing agency, thedate, and the signature of a responsible representative of thetesting agency.11. Precision and Bias11.1 No information is presented about either the precisionor

32、 bias of this test method for measuring leaking of rigid plasticcontainers since the result is non-quantitative. It is recom-mended that test sensitivities be determined and a positive andnegative control be used when validating the test method.FIG. 1 Typical Test Setup for Leakage Testing of Contai

33、ners byVacuum MethodD499107211.2 Once validated, the user does not have to apply thepositive and negative controls before each test.12. Keywords12.1 containers; leakage testing; packaging; vacuummethodAPPENDIX(Nonmandatory Information)X1. TABLE X1.1ASTM International takes no position respecting the

34、 validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is

35、 subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Hea

36、dquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This st

37、andard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or

38、serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE X1.1 Pressure Conversion TablePressureDifferentialAKiloPascalsPounds per squareinch (psi)Inches of mercuryin Hg (20C)Bar10 1.45 2.96 0.1020 2.90 5.93 0.2030 4.35 8.89 0.3040 5.80 11.85 0.4050 7.25 14.82 0.5060 8.70 17.78 0.6070 10.15 20.75 0.7075 10.88 22.23 0.7580 11.60 23.71 0.8085 12.33 25.19 0.8590 13.05 26.67 0.9095 13.78 28.16 0.95100 14.50 29.64 1.00101.325 14.70 30.03 1.01325Apsi 3 6.894757 = kPain. Hg 3 3.37411 = kPabar 3 100 = kPaD4991073