ASTM D4800-1994(2005) Standard Guide for Classifying and Specifying Adhesives《胶粘剂分类和详细说明的标准指南》.pdf

《ASTM D4800-1994(2005) Standard Guide for Classifying and Specifying Adhesives《胶粘剂分类和详细说明的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4800-1994(2005) Standard Guide for Classifying and Specifying Adhesives《胶粘剂分类和详细说明的标准指南》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 4800 94 (Reapproved 2005)Standard Guide forClassifying and Specifying Adhesives1This standard is issued under the fixed designation D 4800; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、 number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide provides a classification system for tabulat-ing the properties of adhesives suitable for holding parts orassemblies toget

3、her. The use of this guide also providesinformation necessary for the development of standard speci-fications for adhesives.NOTE 1This classification system may serve many of the needs ofindustries using adhesives. This guide is subject to revision as the needrequires; therefore, the latest revision

4、 should always be used.1.2 LimitationsThis classification system is intended to bea means of identifying adhesives. It is not intended for theselection of materials. Material selection should be made bythose having expertise in the adhesives field after carefulconsideration of the design and the per

5、formance required of thepart, the environment to which it will be exposed, the attach-ment process to be employed, the inherent properties of thematerial not covered in this document, and the economicfactors.1.3 This classification system is based on the premise thatadhesives can be arranged into br

6、oad generic families usingbasic properties to arrange the materials into groups, classes,and grades.1.4 In all cases where the provisions of this classificationsystem would conflict with the referenced ASTM specificationfor a particular material, the latter shall take precedence.1.5 The values state

7、d in SI units, as detailed in IEEE/ASTMSI 10, are to be regarded as the standard.2. Referenced Documents2.1 ASTM Standards:2D 907 Terminology of AdhesivesD 1084 Test Methods for Viscosity of AdhesivesD 1298 Test Method for Density, Relative Density (SpecificGravity), or API Gravity of Crude Petroleu

8、m and LiquidPetroleum Products by Hydrometer MethodD 1310 Test Method for Flash Point and Fire Point ofLiquids by Tag Open-Cup ApparatusD 2240 Test Method for Rubber PropertyDurometerHardnessD 2583 Test Method for Indentation Hardness of RigidPlastics by Means of a Barcol ImpressorD 2834 Test Method

9、 for Nonvolatile Matter (Total Solids)in Water-Emulsion Floor Polishes, Solvent-Based FloorPolishes, and Polymer-Emulsion Floor PolishesD 3278 Test Methods for Flash Point of Liquids by SmallScale Closed-Cup ApparatusD 4562 Test Method for Shear Strength of Adhesives UsingPin-and-Collar SpecimenD 53

10、63 Specification for Anaerobic Single-Component Ad-hesives (AN)IEEE/ASTM SI 10 Standard for Use of the InternationalSystem of Units (SI): The Modern Metric System2.2 Military Standards:MIL-STD-105 Sampling Procedures and Tables for Inspec-tion by Attributes3MIL-A-46146 Adhesive, Silicone, RTV, Nonco

11、rrosive (forUse with Sensitive Metals and Equipment)33. Terminology3.1 The terms used in this guide are in accordance withTerminology D 907.4. Significance and Use4.1 The purpose of this classification system is to provide amethod of identifying adhesives in order to give industry asystem that can b

12、e used universally for materials. It furtherprovides a means for specifying these materials by the use ofthe standards that are developed using this guide.4.2 This classification system was developed to permit theaddition of future adhesives.1This guide is under the jurisdiction ofASTM Committee D14

13、 onAdhesives andis the direct responsibility of Subcommittee D14.60 on Adhesive Material Classi-fication System.Current edition approved April 1, 2005. Published April 2005. Originallyapproved in 1987. Last previous edition approved in 1999 as D 4800 94 (1999).2For referenced ASTM standards, visit t

14、he ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., P

15、hiladelphia, PA 19111-5098.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Classification5.1 Fig. 1 summarizes the classification system as detailedin this guide.5.2 Adhesives shall be classified on the basis of their broadgeneric

16、 family. The generic family is identified by letterdesignations as found in Table 1.NOTE 2For example: CA = Cyanoacrylate.5.2.1 The generic family is based on the broad chemicalmakeup of the base materials. By its designation, certaininherent properties are specified.5.3 The generic family is classi

17、fied into groups according,in general, to the chemical composition. These groups arefurther subdivided into classes and grades, as shown in thebasic property table that applies. The letter designation appli-cable is followed by a four-digit number indicating group,class, and grade.5.3.1 The basic pr

18、operty tables have been developed toidentify the commercially available adhesives into groups,classes, and grades. These tables are found in the standardslisted in Table 1.5.3.1.1 Where a standard does not exist for this classifica-tion system the letter designation for the generic family will befol

19、lowed by four 0s and the use of the suffixes as needed (see7.1).NOTE 3Example: SI0000 indicates a Silicone (SI) from Table 1, with0000 indicating no basic property table.5.4 To facilitate the identification of new or special materi-als where basic property tables are not provided in a materialspecif

20、ication, cell tables will be used. These tables shall appearin the material specifications. (See example of cell table in Fig.2.)5.4.1 Although the values listed in the cell tables include therange of properties available in existing materials, users shouldnot infer that every possible combination o

21、f properties exists orcan be obtained.5.4.2 The requirements for special adhesives will use theclassification system, as described, by the addition of a singleletter that indicates the proper cell table in which the propertiesare listed. A specific value is designated by the cell number foreach prop

22、erty in the order in which they are listed in the table.When a property is not to be specified, a zero is entered as thecell number. Likewise, when an acceptable value is notavailable in the cell table, the number 9 should be used and asuffix used indicating the specific value (see 7.1). Thus, thele

23、tter designation “A” for cell table and 3400 for propertyvalues shall always be written A3400.NOTE 4An example of an anaerobic adhesive identified by thisclassification system is as follows. The designation AN0120A3400indicates the following with the material requirements from Cell Table Aof materia

24、l specification.AN0120 = AnaerobicNewtonian flow, thread lockingA = Table A for property requirements3 = Strength ASTM Test Method D 4562, 6 MPa min4 = Viscosity ASTM Test Methods D 1084, Method B, 900MPas min0 = Unspecified0 = Unspecified6. Basic Requirements6.1 The cell tables included as part of

25、the listed referencestandard shall be used to develop a line call-out for thematerials listed in Table 1 covered by a material standard.6.2 When the existing cell table does not adequately de-scribe the material, then suffixes may be used in place of a celltable designation.6.3 A line call-out assem

26、bled using the standard becomes aspecification. The line call-out shall contain the broad andspecific type of adhesive together with the appropriate identi-fiers, followed by special suffix requirements, as they apply.12 345| SPECIFIC | CELL REQUIREMENTS | | Table | SuffixBroadGenericTypeGroupXXClas

27、sXGradeX XXXPropertiesZZXXXNOTE 11 = Two or more letters identify the generic family based on abbreviations from Table 1.2 = Four digits identify the specific type. The first two digits identify the group. The next digit identifies the class and the last digit identifies the grade.A basic property t

28、able will provide property values for the specific material (see 5.2).3 = One letter refers to a cell table listing of physical specifications and test methods.4 = Four digits refer to the specific physical parameters listed in the cell table.5 = Suffix codes indicate special requirements based on t

29、he application and identify special tests (two letters with three digits).FIG. 1 Classification SystemTABLE 1 Standard Symbols for Generic FamiliesStandardSymbolAFamily NameASTMStandardBAN Anaerobic (dimethacrylate)BD 5363CA CyanoacrylateCS CaseinCEP EpoxyHM Hot meltMF Melamine-FormaldehydePF Phenol

30、-Formaldehyde (phenolic)PMMA Acrylic (other than AN or CA)PUR PolyurethaneSI SiliconeCAAdditional symbols will be added to this classification system as they arerequested or developed.BThe standards listed are those in accordance with this classification system.CA standard is being developed.D 4800

31、94 (2005)27. Suffix Requirements7.1 When requirements are needed that supersede or supple-ment the property table or cell table requirements, they shall bespecified through the use of suffixes. In general, the first suffixletter indicates the special requirement needed and the secondletter indicates

32、 the condition or test method, or both, with athree-digit number indicating the specific requirement. Thesuffixes that may be used are listed in Table 2.7.2 Basic requirements from property or cell tables, as theyapply, are always in effect unless these requirements aresuperseded by special suffix r

33、equirements in the line call-out.NOTE 5When using the suffixes for additional requirements of thematerial, the user must keep in mind that not all tests are routinelyconducted by the supplier. When these requirements are necessary toidentify particular characteristics important to specific applicati

34、ons theyshall be agreed upon between user and supplier.7.3 When a standard for a material is listed in Table 1, therequirements of the referenced standard apply. If desired, thereferenced standards may be used since a similar system isused in each document. When a standard for a materialspecificatio

35、n is written using this guide, the use of thefollowing sections are recommended (in addition to otherDesignationOrderNumberPropertyCell Limits0123 4 5 6 78 91 Shear strength, ASTMD 4562 MPa, minAUnspecified 2 4 6 8 12 14 20 35 Specify value2 Viscosity, ASTM D 1084,No. 4 spindle, 20 r/minMPas, minBUn

36、specified 10 26 200 900 6500 10 3 10325 3 1031 3 106Specify value3 To be determined Unspecified . . . . . . . .4 To be determined Unspecified . . . . . . . .AMegapascals 3 145 = pounds-force per square inch.BViscosity must not exceed the value in the next highest cell.FIG. 2 Example of Cell Table A

37、Detail RequirementsTABLE 2 Suffix Symbols and RequirementsASymbol CharacteristicA Color (Unless otherwise shown by suffix, color is understood to bethe commercially available color for the material.)Second letter A = does not have to match a standardB = must match standardThree-digit number 001 = co

38、lor and standard number on drawing002 = color on drawingF Flammability, Flash Point, or Fungus ResistanceSecond letter A = ASTM D 1310 (open cup)Three-digit number = minimum value, degrees CelsiusB = ASTM D 3278 (closed cup)Three-digit number = minimum value, degrees CelsiusG Specific GravitySecond

39、letter A = ASTM D 1298 (tolerance 60.02)B = ASTM D 1298 (tolerance 60.05)Three-digit number X factor of 0.01 = requirement valueJ HardnessSecond letter A = ASTM D 2240 (shore A) tolerance 6 5B = ASTM D 2583 (barcol), minimumD = ASTM D 2240 (shore D) tolerance 65R Volatile Loss or SolidsSecond letter

40、 A = ASTM D 2834 (3hat1026 3C)solidsThree-digit number X factor of 0.1 = percent, minimumV Viscosity, Flow Rate, or Extrusion RateSecond letter A = MIL-A-46146 (extrusion rate)Three-digit number = value grams per minute, minimumZ Other Special RequirementsSecond letter from existing list of symbols

41、where test orrequirement is not available.These characteristics will be spelled out in detail and identified insequence, that is 01, 02, 03, etc.Example ZV01ViscosityASTM D 1084RVF, No 4 spindle, and 20 r/min, 6000to 8000 MPasAAdditional suffixes and requirements will be added to this classification

42、 systemas test methods or requirements are developed or requested or both.D 4800 94 (2005)3required sections):General RequirementsDetail RequirementsSamplingSpecimen PreparationConditioningTest MethodsNumber of TestsCertification and InspectionRetest and RejectionPackaging, Packing, and MarkingQuali

43、ty Assurance Provisions for Government orMilitary Procurement (MIL STD 105)For additional guidance in writing standards, refer to themanual Form and Style for ASTM Standards.48. Keywords8.1 adhesives; classificationASTM International takes no position respecting the validity of any patent rights ass

44、erted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time b

45、y the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will rece

46、ive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Inte

47、rnational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).4Available from ASTM International Headquarters.D 4800 94 (2005)4