ASTM D4730-2013 Standard Specification for Flooding Compounds for Telecommunications Wire and Cable《电信电线和电缆用浸渍化合物标准规格》.pdf

《ASTM D4730-2013 Standard Specification for Flooding Compounds for Telecommunications Wire and Cable《电信电线和电缆用浸渍化合物标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4730-2013 Standard Specification for Flooding Compounds for Telecommunications Wire and Cable《电信电线和电缆用浸渍化合物标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4730 13 An American National StandardStandard Specification forFlooding Compounds for Telecommunications Wire andCable1This standard is issued under the fixed designation D4730; the number immediately following the designation indicates the year oforiginal adoption or, in the case of r

2、evision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers a variety of compounds usedfor flooding the shields and armors of tele

3、communicationswires and cables (both electrical and fiber optic) for thepurpose of preventing water and other undesirable fluids fromentering or migrating along or through the cable sheath. (Forrelated standards see Specifications D4731 and D4732.)2. Referenced Documents2.1 ASTM Standards:2D6 Test M

4、ethod for Loss on Heating of Oil and AsphalticCompoundsD92 Test Method for Flash and Fire Points by ClevelandOpen Cup TesterD482 Test Method for Ash from Petroleum ProductsD1321 Test Method for Needle Penetration of PetroleumWaxesD3236 Test Method for Apparent Viscosity of Hot MeltAdhesives and Coat

5、ing MaterialsD4565 Test Methods for Physical and Environmental Per-formance Properties of Insulations and Jackets for Tele-communications Wire and CableD4568 Test Methods for Evaluating Compatibility BetweenCable Filling and Flooding Compounds And PolyolefinWire and Cable MaterialsD4731 Specificatio

6、n for Hot-Application Filling Com-pounds for Telecommunications Wire and CableD4732 Specification for Cool-Application Filling Com-pounds for Telecommunications Wire and CableE28 Test Methods for Softening Point of Resins Derivedfrom Naval Stores by Ring-and-Ball Apparatus3. Terminology3.1 Definitio

7、ns of Terms Specific to This Standard:3.1.1 flooding compoundsany of several materials used tofill the air spaces between the sheath elements of single andmulti-conductor insulated wires and cables or optical cables forthe purpose of excluding water and other undesirable fluids;especially with regar

8、d to telecommunications wire and cable,including optical cable, intended for outside aerial or under-ground installations.3.1.2 producerthe primary manufacturer of the material.3.1.3 suppliersjobbers and distributors as distinct fromproducers.4. Ordering Information4.1 Orders for material under this

9、 specification shall includethe following information:4.1.1 Quantity (mass or volume) of each item,4.1.2 Generic name of the material, such as cable floodingcompound,4.1.3 How furnished (drums or barrels, blocks, etc.),4.1.4 Certification, if required (see Section 11).4.1.5 This specification design

10、ation, and4.1.6 Any special requirements, as listed in 8.2 and 9.2, thatapply.5. Materials and Manufacture5.1 The material and manufacturing methods used shall besuch that the resulting products conform to the properties andcharacteristics prescribed in this specification.6. Compatibility with Other

11、 Materials6.1 It is the responsibility of the purchaser to ensure that theflooding compound ordered is suitable for the intended appli-cation and is compatible with any other components that maycome into contact with the flooding compound.6.2 The purchaser shall specify the materials that the com-po

12、und must be compatible with when tested in accordance withTest Method D4568.7. Chemical Composition7.1 The chemical composition of these materials is notspecified. The material shall be of a chemical composition1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Elec

13、tronic Insulating Materials and is under the direct responsibilityof Subcommittee D09.18 on Solid Insulations, Non-Metallic Shieldings andCoverings for Electrical and Telecommunication Wires and Cables.Current edition approved May 1, 2013. Published June 2013. Originallyapproved in 1987. Last previo

14、us edition approved in 2008 as D4730 02 (2008).DOI: 10.1520/D4730-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM

15、website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1suitable for the intended purpose and which meets the require-ments of this specification as hereinafter stated.7

16、.2 Once established, the producer shall not change thecomposition of the compound in successive lots of materialwithout prior approval of the purchaser.8. Physical Properties8.1 Flooding compound furnished under this specificationshall inhibit the corrosion of any metallic wire and cableelements wit

17、h which it comes in contact, while serving as aradial and longitudinal barrier to moisture transmission. Con-tact of the flooding compound with any cable component shallnot cause degradation of performance of the cable component.The flooding compound shall display adhesive properties toprovide adhes

18、ion between metallic sheath elements and theouter jacket materials of wire and cable.8.2 Other Properties:8.2.1 Other physical properties requirements such as Vis-cosity (for example, Test Method D3236), Flash Point (forexample, Test Method D92), Needle Penetration (for example,Test Method D1321), R

19、ing-and-Ball Softening Point (forexample, Test Method E28), and Heat Stability/ViscosityChange (for example, Test Method D3236), are specified, ifneeded, and shall be as agreed-upon between the producer andthe purchaser.8.3 The purchaser (individual cable manufacturer or other)shall specify any othe

20、r expected requirements needed to ensurecompliance with such end-product requirements as cold-bend,low-temperature flexibility, and the like (for example, TestMethods D4565).9. General Requirements9.1 All flooding compounds manufactured in conformanceto this specification shall meet the following re

21、quirements:9.1.1 HomogeneityThe compound shall be homogeneousand uniformly mixed.9.1.2 Foreign MaterialThe compounds shall be free ofdirt, metallic particles, and other foreign matter.9.2 Other Properties:9.2.1 Other raw material requirements such as Volatility (forexample, Test Method D6), Metals C

22、ontent (for example, TestMethod D482), adhesive property measurements, and corro-sion inhibiting characteristics are specified, if needed, and shallbe as agreed-upon between the producer and the purchaser.9.3 The purchaser (individual cable manufacturer or other)shall specify any other expected requ

23、irements needed to ensurecompliance with such end-product requirements as cabledrip-out temperature and jacket slip.10. Quality Assurance10.1 Responsibility for Inspection and TestsUnless other-wise specified in the contract or purchase order, the producer isresponsible for the performance of all in

24、spection and testrequirements specified herein. The producer shall use his ownor any other suitable facilities for the performance of theinspection and test requirements specified herein, unless oth-erwise stated by the purchaser in the order or at the time of thecontract signing. The purchaser shal

25、l have the right to performany of the inspections and tests set forth in this specificationwhere such inspections are deemed necessary to assure that thematerial conforms to prescribed requirements.10.2 Each producer shall establish written nominal valuesand tolerances for the material properties ro

26、utinely checked.For properties not routinely checked, typical values shall bespecified. Once these values have been accepted by thepurchaser, the producer shall not ship material which deviatesfrom these limits without prior notification to and approval bythe purchaser.10.3 An inspection lot shall c

27、onsist of an identifiable quan-tity of the same material subjected to inspection at one time.11. Certification11.1 The producer or supplier shall, on request, furnish tothe purchaser a certificate stating that each lot has beensampled, tested, and inspected in accordance with thisspecification, and

28、has met the requirements.12. Packaging and Package Marking12.1 PackagingThe flooding compound shall be packagedin a manner that protects the material from contaminationduring shipment.12.2 Package MarkingShipping containers shall bemarked with the name of the manufacturer, trade name, type ofmateria

29、l, lot number, mass or volume, and date of manufacture.13. Keywords13.1 adhesive; compatibility; flooding compound; moisturebarrier; telecommunications wire and cableD4730 132SUMMARY OF CHANGESCommittee D09 has identified the location of selected changes to this standard since the last issue(D4730 0

30、2R08) that may impact the use of this standard. (Approved May 1, 2013.)(1) Deleted “will” in 5.1.(2) Changed “that may come” to “that come” in 6.1.(3) Changed “may” to “shall” and “any” to “a” in 7.1.(4) Changed “may be” to “are” in 8.2.1 and 9.2.1.(5) Changed “The producer may” to “The producer sha

31、ll” in10.1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such

32、rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additio

33、nal standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the A

34、STM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D4730 133