ASTM D3950-2009a Standard Specification for Strapping Nonmetallic (and Joining Methods).pdf

《ASTM D3950-2009a Standard Specification for Strapping Nonmetallic (and Joining Methods).pdf》由会员分享，可在线阅读，更多相关《ASTM D3950-2009a Standard Specification for Strapping Nonmetallic (and Joining Methods).pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 3950 09aStandard Specification forStrapping, Nonmetallic (and Joining Methods)1This standard is issued under the fixed designation D 3950; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers nonmetallic strapping andjoi

3、ning methods intended for use in closing, reinforcing, andbundling articles for shipment, unitizing, palletizing, andbracing for car loading and truck loading.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI un

4、its that are provided for information onlyand are not considered standard.1.3 The following safety hazards caveat pertains only to thetest method portion, Section 12, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the

5、 responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D 996 Terminology of Packaging and Distribution Environ-mentsD 3951 Practice for Commerci

6、al PackagingD 4332 Practice for Conditioning Containers, Packages, orPackaging Components for Testing2.2 Other Standards:ANSI/ASQC Z 1.4 Sampling Procedures and Tables forInspection by Attributes3ANSI/ASQC Z 1.9 Sampling Procedures and Tables forInspection by Variables for Percent Nonconforming33. T

7、erminology3.1 For general definitions of packaging and distributionenvironments, see Terminology D 996.4. Classification4.1 Types and Grades:Type I Strapping, bonded rayon cord.Grade 1Light duty.Grade 2Regular duty.Grade 3Heavy duty.Type IA Strapping, bonded, or woven polyester cord.Grade 1Light dut

8、y.Grade 2Regular duty.Grade 3Heavy duty.Grade 4Extra heavy duty.Grade 5Special duty.Grade 6Special duty.Grade 7Special duty.Type II Strapping, polypropylene plastic.Type III Strapping, nylon plastic.Type IV Strapping, polyester plastic.5. Ordering Information5.1 The inquiry and order shall indicate

9、the following:5.1.1 Type, grade, and dimensions required (see 4.1 and7.1),5.1.2 Length per coil (see 8.1),5.1.3 Joining method (see 6.2), type and size required (ifneeded),5.1.4 If an embossed finish on strapping is desired orallowed (see Footnote in Table 1, Table 2, and Table 3),5.1.5 Make and mod

10、el of strapping equipment that thestrapping and joining method must work in, if applicable,5.1.6 Coil dimensions (see 8.1),5.1.7 Level of packaging and packing if other than commer-cial (see Section 15), and5.1.8 ASTM designation and date of issue.6. Materials and Manufacture6.1 Materials shall be o

11、f the quality necessary to meet thephysical requirements within the allowable dimensions.6.1.1 Type IStrapping shall consist of longitudinal rayoncords bonded with a plastic binder so that a nonwoven materialis formed.6.1.1.1 Type IAStrapping shall consist of longitudinalpolyester cords bonded with

12、a plastic binder to form anonwoven material or longitudinal polyester cords woven witha weft thread and treated with a plastic binder to form a wovenmaterial.1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.25 on Pal

13、letizingand Unitizing of Loads.Current edition approved Oct. 1, 2009. Published October 2009. Originallyapproved in 1980. Last previous edition approved in 2009 as D 3950 09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For

14、Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box

15、 C700, West Conshohocken, PA 19428-2959, United States.6.1.2 Type IIStrapping shall be an extruded, orientedpolypropylene.6.1.3 Type IIIStrapping shall be an extruded, orientednylon.6.1.4 Type IVStrapping shall be an extruded, orientedpolyester.6.2 Joining MethodsIf seals or buckles are to be used,t

16、hey shall be steel and have a coating of zinc, black iron oxide,or equivalent protection from corrosion, or buckles may bemade of plastic.7. Mechanical Properties7.1 Breaking Strength and Elongation (see 12.2):7.1.1 Type I and Type IA strapping shall conform to thebreaking strengths and elongations

17、prescribed in Table 4 andTable 5.7.1.2 Type II strapping shall conform to the breakingstrengths and elongations prescribed in Table 1.7.1.3 Type III strapping shall conform to the breakingstrengths and elongations prescribed in Table 2.7.1.4 Type IV strapping shall conform to the breakingstrengths a

18、nd elongations prescribed in Table 3.7.2 Transverse strength of Types I and IA strapping shall bea minimum of 2.75 lbf (12.2 N) and 2.25 lbf (10 N),respectively, when tested in accordance with 12.4.7.3 Joint Strength (see 12.3).7.3.1 Type I and Type IA Grade 1 and Grade 2 joinedstrapping shall have

19、a strength of not less than 45% of theminimum breaking strength of the strapping grade and sizelisted in Table 4 and Table 5.7.3.2 Type IA Grade 3, Grade 4, Grade 5, Grade 6, andGrade 7 joined strapping shall have a strength of not less than55 % of the minimum breaking strength of the strapping grad

20、eand size listed in Table 5. Test data are available to substantiatethis conclusion.7.3.3 Types II, III, and IV joined strapping shall have astrength of not less than 45 % of the minimum breakingstrength corresponding to the dimensions of the strap listed inTable 1, Table 2,orTable 3.8. Dimensions a

21、nd Permissible Variations8.1 The minimum length per coil of strapping shall be asspecified in the following tables according to type, grade, size,and coil width. The coil shall be an oscillating or ribbon wind.8.1.1 Type I and Type IA strapping shall be furnished withthe minimum feet per coil accord

22、ing to size and grade asprescribed in Table 6.8.1.2 Types II, III, and IV strapping shall be furnished withthe minimum feet per coil in accordance with the size and coilwidth in Table 7.TABLE 1 Breaking Strengths of Type II Strapping (PP)Nominal Widthof StrappingNominal Thicknessof StrappingMinimumB

23、reaking Strengthin. (mm) in. (mm)Alb (N)B0.197 (5.0) 0.0120 (0.30) 80 (360)0.197 (5.0) 0.0145 (0.37) 100 (440)0.234 (5.9) 0.0135 (0.34) 130 (580)0.234 (5.9) 0.0140 (0.36) 155 (690)0.236 (6.0) 0.0130 (0.33) 135 (600)0.234 (5.9) 0.0160 (0.41) 180 (800)0.236 (6.0) 0.0173 (0.44) 190 (850)14 (6.4) 0.0135

24、 (0.34) 134 (600)14 (6.4) 0.0150 (0.38) 180 (800)14 (6.4) 0.0250 (0.64) 200 (890)0.351 (8.9) 0.0130 (0.33) 200 (899)0.354 (9.0) 0.0142 (0.36) 225 (1 000)0.351 (8.9) 0.0160 (0.41) 270 (1 200)0.354 (9.0) 0.0173 (0.44) 270 (1 200)0.354 (9.0) 0.0181 (0.46) 270 (1 200)38 (9.5) 0.0180 (0.46) 250 (1 110)38

25、 (9.5) 0.0150 (0.38) 290 (1 290)38 (9.5) 0.0200 (0.51) 390 (1 730)38 (9.5) 0.0250 (0.64) 400 (1 780)0.413 (10.5) 0.0190 (0.48) 360 (1 600)0.413 (10.5) 0.0201 (0.51) 360 (1 600)0.413 (10.5) 0.0248 (0.63) 460 (2 050)0.413 (10.5) 0.0295 (0.75) 550 (2 450)0.413 (10.5) 0.0295 (0.75) 540 (2 400)0.413 (10.

26、5) 0.0230 (0.58) 450 (2 000)716 (11.1) 0.0140 (0.36) 300 (1 330)716 (11.1) 0.0190 (0.48) 350 (1 560)716 (11.1) 0.0230 (0.58) 420 (1 870)716 (11.1) 0.0250 (0.64) 450 (2 000)716 (11.1) 0.0300 (0.76) 550 (2 450)0.468 (11.9) 0.0215 (0.55) 450 (2 000)0.472 (12.0) 0.0169 (0.43) 360 (1 600)0.472 (12.0) 0.0

27、212 (0.54) 460 (2 050)0.472 (12.0) 0.0252 (0.64) 550 (2 450)0.480 (12.2) 0.0190 (0.48) 400 (1.780)12 (12.7) 0.0150 (0.38) 390 (1.750)12 (12.7) 0.0170 (0.43) 350 (1 570)12 (12.7) 0.0220 (0.56) 450 (2 020)12 (12.7) 0.0200 (0.51) 530 (2 360)12 (12.7) 0.0250 (0.64) 660 (2 940)12 (12.7) 0.0260 (0.66) 550

28、 (2 450)12 (12.7) 0.0300 (0.76) 810 (3 600)0.468 (12.0) 0.0255 (0.65) 540 (2 400)0.591 (15.0) 0.0410 (1.04) 1 050 (4 660)58 (15.9) 0.0150 (0.38) 500 (2 200)58 (15.9) 0.0200 (0.51) 680 (3 020)58 (15.9) 0.0300 (0.76) 950 (4 220)0.728 (18.5) 0.0410 (1.04) 1 300 (5 770)34 (19.1) 0.0200 (0.51) 725 (3 220

29、)114 (31.8) 0.0350 (0.89) 2 200 (9 790)114 (31.8) 0.0500 (1.27) 3 100 (13 790)AWhen specified (see 5.1.4), the strapping as measured by a flat anvilmicrometer shall have an embossed finish which yields an overall nominalthickness no greater than twice the nominal thickness of smooth-surfaced strap-p

30、ing of the same width and breaking strength.BRange of elongation at break is from 7 to 35 %.TABLE 2 Breaking Strengths of Type III Strapping (Nylon)Nominal Widthof Strapping,in. (mm)Nominal Thicknessof Strapping, in. (mm)AMinimum BreakingStrength, lbf (N)B716 (11.1) 0.017 (0.43)0.023 (0.58)0.029 (0.

31、74)420 (1870)560 (2490)700 (3110)12 (12.7) 0.015 (0.38) 420 (1870)0.020 (0.51) 560 (2490)0.025 (0.64) 700 (3110)0.030 (0.76) 900 (4000)AWhen specified (see 5.1.4), the strapping as measured by a flat anvilmicrometer shall have an embossed finish which yields an overall nominalthickness no greater th

32、an twice the nominal thickness of smooth-surfaced strap-ping of the same width and breaking strength.BRange of elongation at break is from 12 to 25 %.D 3950 09a29. Workmanship, Finish, and Appearance9.1 Type I and Type IA strapping shall be straight, clean,have good webbing, and be free of cracks an

33、d other defects thatmay affect the serviceability.9.2 Types II, III, and IV strapping shall be straight, clean,and free of kinks, edge curvature, cracks, and other defects thatmay affect the serviceability.9.3 Splices may be made if they do not affect the service-ability of the strapping in strappin

34、g equipment and have abreak strength equal to at least 50% of the strap break strength.No more than one splice per coil will be permitted.10. Sampling Plan10.1 Where it can be demonstrated that a suppliers qualitycontrol system provides a similar degree of assurance as thatobtained through the use o

35、f this specification, the supplier mayuse that system in place of the system described in thisTABLE 3 Breaking Strengths of Type IV Strapping (PET)Nominal Widthof StrappingNominal Thicknessof StrappingMinimumBreaking Strengthin. (mm) in. (mm)Alb (N)B0.351 (8.9) 0.0190 (0.48) 390 (1 730)0.354 (9.0) 0

36、.0205 (0.52) 400 (1 780)38 (9.5) 0.0150 (0.38) 310 (1 380)38 (9.5) 0.0200 (0.51) 420 (1 870)0.413 (10.5) 0.0195 (0.50) 430 (1 910)0.413 (10.5) 0.0205 (0.52) 460 (2 050)0.413 (10.5) 0.0220 (0.56) 500 (2 220)0.413 (10.5) 0.0240 (0.61) 560 (2 490)0.413 (10.5) 0.0255 (0.65) 575 (2.550)0.413 (10.5) 0.026

37、5 (0.67) 600 (2 660)716 (11.1) 0.0160 (0.41) 360 (1 600)716 (11.1) 0.0200 (0.51) 460 (2 050)716 (11.1) 0.0220 (0.56) 500 (2 220)716 (11.1) 0.0240 (0.61) 560 (2 490)0.468 (11.9) 0.0168 (0.43) 470 (2 090)0.468 (11.9) 0.0175 (0.44) 470 (2 090)0.468 (11.9) 0.0205 (0.52) 560 (2 490)0.468 (11.9) 0.0275 (0

38、.70) 750 (3 340)0.468 (11.9) 0.0280 (0.71) 750 (3 340)0.472 (12.0) 0.0175 (0.44) 470 (2 090)0.472 (12.0) 0.0205 (0.52) 560 (2 490)0.472 (12.0) 0.0280 (0.71) 750 (3 340)12 (12.7) 0.0150 (0.38) 420 (1 870)12 (12.7) 0.0170 (0.43) 470 (2 090)12 (12.7) 0.0200 (0.51) 560 (2 490)12 (12.7) 0.0250 (0.64) 700

39、 (3 110)12 (12.7) 0.0280 (0.71) 750 (3 340)12 (12.7) 0.0300 (0.76) 850 (3 780)0.615 (15.6) 0.0300 (0.76) 1 000 (4 440)0.615 (15.6) 0.0350 (0.89) 1 100 (4 890)0.615 (15.6) 0.0360 (0.91) 1 150 (5 120)0.615 (15.6) 0.0380 (0.97) 1 200 (5 328)0.615C(15.6) 0.0400 (1.02) 1 200 (5 328)0.615 (15.6) 0.0400 (1

40、.02) 1 500 (6 670)0.615C(15.6) 0.0410 (1.04) 1 200 (5 328)0.615 (15.6) 0.0450 (1.14) 1 600 (7 120)58 (15.9) 0.0200 (0.51) 700 (3 110)58 (15.9) 0.0250 (0.64) 870 (3 870)58 (15.9) 0.0300 (0.76) 1 000 (4 450)58C(15.9) 0.0350 (0.89) 1 200 (5 340)58 (15.9) 0.0350 (0.89) 1 300 (5 780)34 (19.1) 0.0400 (1.0

41、2) 1 750 (7 780)34 (19.1) 0.0500 (1.27) 2 250 (10 010)34 (19.1) 0.0550 (1.40) 2 400 (10 680)34 (19.1) 0.0600 (1.52) 2 500 (11 120)0.985 (25.0) 0.0400 (1.02) 2 300 (10 210)0.985 (25.0) 0.0500 (1.27) 2 800 (12 460)114 (32.0) 0.0320 (0.82) 2 250 (10 010)114 (32.0) 0.0400 (1.02) 2 800 (12 460)AWhen spec

42、ified (see 5.1.4), the strapping as measured by a flat anvilmicrometer shall have an embossed finish which yields an overall nominalthickness no greater than twice the nominal thickness of smooth-surfaced strap-ping of the same width and breaking strength.BUltimate Elongation Range: 5 to 20 % (Stand

43、ard Elongation PET),10 to 25 % (High Elongation PET)CDenotes High Elongation (H.E.) PET strapping.TABLE 4 Breaking StrengthsAof Type I Bonded Rayon CordStrappingNominal Widthof Strapping,in. (mm)GradeMinimum BreakingStrength, lbf (N)14 (6.4) 2 235 (1045)38 (9.5) 12290 (1290)350 (1555)12 (12.7) 12410

44、 (1820)465 (2070)58 (15.9) 123525 (2335)585 (2600)765 (3400)34 (19.1) 123640 (2845)700 (3110)900 (4000)114 (31.8) 3 157 (7005)ARange of elongation at break is from 10 to 15 %.TABLE 5 Breaking StrengthsAof Type IA Bonded or WovenPolyester Cord StrappingNominal Widthof Strapping,in. (mm)GradeMinimum B

45、reakingStrength, lbf (N)14 (6.4)(6.0)23300 (1 335)540 (2 400)38 (9.5)(9.0)23450 (2 000)780 (3 480)12 (12.7) 1 400 (1 780)(12.7) 2 600 (2 670)(13.0) 3 1 050 (4 670)(13.0) 4 1 360 (6 050)58 (15.9) 1 500 (2 225)(15.9) 2 725 (3 225)(16.0) 3 1 310 (5 830)(16.0) 4 1 650 (7 340)34 (19.1) 2 900 (4 000)(19.0

46、) 3 1 585 (7 060)(19.0) 4 1 830 (8 150)(19.0) 5 2 600 (11 570)114 (32.0) 2 1 830 (8 150)(32.0) 3 2 105 (9 370)(32.0) 4 3 285 (14 620)(32.0) 5 4 200 (18 680)112 (38.0) 4 4 400 (19 570)112 (38.0) 5 5 400 (24 030)158 (40.0) 6 7 700 (34 265)158 (40.0) 7 11 000 (48 950)ARange of elongation at break is fr

47、om 9 to 15 %.D 3950 09a3specification. In case of conflict, provisions set forth inANSI/ASQC Z1.4 shall be used.10.2 Lot SizeThe lot size shall be expressed in units ofcoils or joining methods, or both, and shall consist of allproducts of one type, grade, and size offered for acceptance atone time.1

48、0.3 Unit Sample One coil or one joining method shall beconsidered a unit. A minimum of 10 ft (3.05 m) per coil ofstrapping is required to perform the tests.10.4 Rate of SamplingThe rate of sampling shall be inaccordance with ANSI/ASQC Z1.9; Table A-2 reduced inspec-tion level shall be used.11. Numbe

49、r of Tests11.1 TestsFor the determination of break strength, elon-gation, transverse strength, and sealed joint strength, an aver-age of three specimens per coil shall be considered a completetest.11.2 RetestsWhen testing for elongation, if the specimenfails outside of the center third of the gage length or within 1in. of the jaws, a retest shall be made. If the percentage ofelongation or the break strength is less than the specifiedminimum, a retest is permitted. In this retest, thr