ASTM D2665-2014 Standard Specification for Poly&40 Vinyl Chloride&41 &40 PVC&41 Plastic Drain Waste and Vent Pipe and Fittings《聚40 氯乙烯41 40 PVC41塑料排水 污水及排气管件和配件的标准规范》.pdf
《ASTM D2665-2014 Standard Specification for Poly&40 Vinyl Chloride&41 &40 PVC&41 Plastic Drain Waste and Vent Pipe and Fittings《聚40 氯乙烯41 40 PVC41塑料排水 污水及排气管件和配件的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2665-2014 Standard Specification for Poly&40 Vinyl Chloride&41 &40 PVC&41 Plastic Drain Waste and Vent Pipe and Fittings《聚40 氯乙烯41 40 PVC41塑料排水 污水及排气管件和配件的标准规范》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2665 12D2665 14 An American National StandardStandard Specification forPoly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and VentPipe and Fittings1This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year oforiginal ad
2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defe
3、nse.1. Scope*1.1 This specification covers requirements and test methods for materials, dimensions and tolerances, pipe stiffness, crushresistance, impact resistance, and solvent cement for poly(vinyl chloride) plastic drain, waste, and vent pipe and fittings. A formof marking is also included. Plas
4、tic which does not meet the material requirements specified in Section 5 is excluded. Installationprocedures are given in the Appendix.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided f
5、or information only and are not considered standard.1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.4 The
6、 following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and
7、health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) C
8、ompounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impa
9、ct Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (FallingWeight)D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping SystemsD3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings PatternsF402 Practice for Safe Handling of Solvent Ceme
10、nts, Primers, and Cleaners Used for Joining Thermoplastic Pipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and FittingsF1866 Specification for Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabr
11、icated FittingsF2135 Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings3. Terminology3.1 Definitions: DefinitionsDefinitions are in accordance with Terminology F412, and abbreviations are in accordance withTerminology D1600, unless otherwise specified.1 This specifi
12、cation is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved April 1, 2012May 1, 2014. Published May 2012June 2014. Originally approved in 1968. Last previous edition approved in 20112012 asD2
13、665 11.D2665 12. DOI: 10.1520/D2665-12.10.1520/D2665-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This
14、document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions
15、 as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. Un
16、ited States13.1 Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology D1600, unlessotherwise specified.4. Significance and Use4.1 The requirements of this specification are intended to provide pipe and fittings suitable for the drainage and venting
17、 ofsewage and certain other liquid wastes.NOTE 1Industrial waste disposal lines should be installed only with the specific approval of the cognizant building code authority since chemicalsnot commonly found in drains and sewers and temperatures in excess of 180F (82.2C) may be encountered.NOTE 2This
18、 specification does not include requirements for pipe and fittings intended to be used to vent combustion gases.5. Materials5.1 Basic MaterialsThe pipe shall be made of virgin PVC compounds meeting or exceeding the requirements of Class 12454as defined in Specification D1784. The fittings shall be m
19、ade of virgin PVC compounds meeting or exceeding the requirementsof Class 12344 as defined in Specification D1784, but with a tensile strength of not less than 6500 psi and a modulus of elasticityfor not less than 380,000 psi. These plastics contain stabilizers, lubricants, and pigments.5.2 Rework M
20、aterialThe manufacturer shall use only his own clean pipe or fitting rework material, and the pipe or fittingsproduced shall meet all the requirements of this specification.5.3 Solvent CementThe solvent cement used to join pipe and fittings made to this specification shall meet the requirementsof Sp
21、ecification D2564.6. Requirements6.1 GeneralThe pipe and fittings shall be homogeneous throughout and free of visible cracks, holes, foreign inclusions, orother injurious defects. The pipe shall be as uniform as commercially practicable in color, opacity, density, and other physicalproperties.6.1.1
22、The requirements in this section are intended only for use as quality control tests, not as simulated service tests.6.2 Dimensions and Tolerances:6.2.1 MethodAll dimensions shall be determined in accordance with Test Method D2122.6.2.2 Dimensions:6.2.2.1 The outside diameter and wall thicknesses of
23、pipe shall meet the requirements of Table 2. The pipe shall be in either10 or 20-ft (3.05 or 6.1-m) lengths, unless otherwise specified, with an allowable tolerance of +12, 0 in. (+13, 0 mm).6.2.2.2 The patterns, dimensions, and laying lengths of fittings, including adaptors, shall meet the requirem
24、ents of SpecificationD3311 and Table 1.6.2.2.3 Reducer bushings of sizes 2 by 114 and 4 by 3 shall be permitted to have the socket wall thickness and spigot wallthickness below the minimum requirements defined in Table 1, but not less than 0.098 in. (2.5 mm), provided the inner socket andouter spigo
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD26652014STANDARDSPECIFICATIONFORPOLY40VINYLCHLORIDE4140PVC41PLASTICDRAINWASTEANDVENTPIPEANDFITTINGS

链接地址:http://www.mydoc123.com/p-513280.html