ASTM D2584-2011 Standard Test Method for Ignition Loss of Cured Reinforced Resins《固化增强树脂燃烧损失的标准试验方法》.pdf
《ASTM D2584-2011 Standard Test Method for Ignition Loss of Cured Reinforced Resins《固化增强树脂燃烧损失的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2584-2011 Standard Test Method for Ignition Loss of Cured Reinforced Resins《固化增强树脂燃烧损失的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2584 11Standard Test Method forIgnition Loss of Cured Reinforced Resins1This standard is issued under the fixed designation D2584; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in
2、 parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test method covers the determination of the ignitionloss o
3、f cured reinforced resins. This ignition loss can beconsidered to be the resin content within the limitations of 4.2.1.2 The values stated in SI units are to be regarded as thestandard.1.3 This standard is used to measure and describe theresponse of composite material to heat under controlledconditi
4、ons, but does not by itself incorporate all of the factorsrequired for fire hazard or fire assessments of the compositematerials under actual fire conditions.1.4 Fire testing is inherently hazardous. Adequate safe-guards for personnel and property shall be employed inconducting these tests.1.5 This
5、standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of whoever uses this standard to consult andestablish appropriate safety and health practices and deter-mine the applicability of regulatory limitations prior to use.NOTE 1There i
6、s no known ISO equivalent to this standard.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Summary of Test Method3.1 The specimen contained in a crucible i
7、s ignited andallowed to burn until only ash and carbon remain. Thecarbonaceous residue is reduced to an ash by heating in amuffle furnace at 565C (1050F), cooled in a desiccator, andweighed.4. Significance and Use4.1 This test method can be used to obtain the ignition lossof a cured reinforced resin
8、 sample. This test method can also beused to examine the fiber architecture of pultruded structuralshapes.4.2 If only glass fabric or filament is used as the reinforce-ment of an organic resin that is completely decomposed tovolatile materials under the conditions of this test and the smallamount of
9、 volatiles (water, residual solvent) that are potentiallypresent are ignored, the ignition loss can be considered to bethe resin content of the sample.4.2.1 This test method does not provide a measure of resincontent for samples containing reinforcing materials that loseweight under the conditions o
10、f the test or containing resins orfillers that do not decompose to volatile materials released byignition.5. Apparatus5.1 Crucible, platinum or porcelain, approximately 30-mLcapacity.5.2 Electric Muffle Furnace, capable of maintaining a tem-perature of 565 6 28C (1050 6 50F).6. Test Specimen6.1 A mi
11、nimum of three specimens shall be tested for eachsample.NOTE 2It is often convenient to use samples obtained from specimensthat have been tested for mechanical properties such as flexural or tensilestrength. Specimens obtained from these samples must be dry and thefractured areas removed, leaving sq
12、uare, unfrayed faces, before beingweighed and ignited.6.2 The specimen shall weigh approximately 5 g with amaximum size of 2.5 by 2.5 cm by thickness (1 by 1 in. bythickness).NOTE 3Materials that have gross differences in the ratio of resin toreinforcement within an area as small as 2.5 by 2.5 cm (1
13、 by 1 in.) mayrequire a larger specimen area than that listed in 6.2. If larger specimensare utilized, it will be necessary to cut into approximately 2.5 by 2.5-cm(1 by 1-in.) pieces and place in a crucible of sufficient size to contain thespecimen.1This test method is under the jurisdiction of ASTM
14、 Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.18 on Reinforced Thermoset-ting Plastics.Current edition approved Oct. 15, 2011. Published November 2011. Originallyapproved in 1967. Last previous edition approved in 2008 as D2584 - 08. DOI:10.1520/D2584-11.2For referen
15、ced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West C
16、onshohocken, PA 19428-2959, United States.7. Conditioning7.1 ConditioningCondition the test specimens at 236 2C(73.4 6 3.6F) and 50 6 10 % relative humidity for not lessthan 40 h prior to test in accordance with Procedure A ofPractice D618 for those tests where conditioning is required. Incases of d
17、isagreement, the tolerances shall be 61C (61.8F)and 65 % relative humidity. The conditioning is not required ifthe test is only performed to examine the fiber architecture.7.2 Test ConditionsConduct tests in the standard labora-tory atmosphere of 23 6 2C (73.4 6 3.6F) and 50 6 10 %relative humidity,
18、 unless otherwise specified in the test meth-ods or in the specification. In cases of disagreement, thetolerances shall be 61C (61.8F) and 610 % relative humid-ity.8. Procedure8.1 Heat a crucible at 500 to 600C for 10 min or more.Cool to room temperature in a desiccator and weigh to thenearest 1.0 m
19、g. The desiccator is not required if the test isperformed only to examine the fiber architecture.8.2 Place the specimen in the crucible and weigh to thenearest 1.0 mg. Heat the crucible and specimen in a bunsenflame until the contents ignite. Maintain such a temperaturethat the specimen burns at a u
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD25842011STANDARDTESTMETHODFORIGNITIONLOSSOFCUREDREINFORCEDRESINS 固化 增强 树脂 燃烧 损失 标准 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-513126.html