ASTM D868-2010(2015) Standard Practice for Determination of Degree of Bleeding of Traffic Paint《测定路标漆渗色程度的标准实施规程》.pdf
《ASTM D868-2010(2015) Standard Practice for Determination of Degree of Bleeding of Traffic Paint《测定路标漆渗色程度的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM D868-2010(2015) Standard Practice for Determination of Degree of Bleeding of Traffic Paint《测定路标漆渗色程度的标准实施规程》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D868 10 (Reapproved 2015)Standard Practice forDetermination of Degree of Bleeding of Traffic Paint1This standard is issued under the fixed designation D868; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l
2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes test procedures for determiningthe degree of bleeding of traffic or pavement marking paints. As
3、pecific formulation for a solventborne traffic paint formulationis included as a potential bleeding reference control.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thes
4、afety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D226 Specification for Asphal
5、t-Saturated Organic Felt Usedin Roofing and WaterproofingD227 Specification for Coal-Tar-Saturated Organic FeltUsed in Roofing and WaterproofingD476 Classification for Dry Pigmentary Titanium DioxideProductsD867 Specification for Pumice Pigment (Withdrawn 1993)3D1199 Specification for Calcium Carbon
6、ate PigmentsD2244 Practice for Calculation of Color Tolerances andColor Differences from Instrumentally Measured ColorCoordinatesE1347 Test Method for Color and Color-Difference Mea-surement by Tristimulus Colorimetry3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bleeding cha
7、racteristic, nthat condition of discolor-ation manifested in traffic paint when applied to tar orasphaltic-type substrates.3.1.1.1 DiscussionThe amount of discoloration can becomparing the color of the test coating and a specific referencecoating using colorimetric measurements or by visual compari-
8、son to the amount of bleeding in a reference photograph.4. Significance and Use4.1 Solvents in a traffic paint may cause bleeding ofpavement constituents into the traffic marking, thereby render-ing the traffic marking less effective as a lane or directionalindicator. This practice describes how to
9、prepare a panel of thecoating to be tested and a reference panel coated with a specificsolventborne traffic paint to be used as a control for evaluation.4.2 This practice can be particularly useful for evaluation ofsolventborne traffic paints, but it may also be used for othertypes of traffic markin
10、gs including waterborne traffic paints.4.3 Two basic procedures are described for measuring theamount of bleeding. The procedure used shall be agreed uponby the purchaser and seller.5. Apparatus5.1 Film ApplicatorA conventional type drawdown gagethat casts a film having a minimum width of 50 mm (2 i
11、n.) andan approximate wet thickness of 380 m (15 mils) (using anapplicator clearance of approximately 760 m (30 mils).5.2 Test Panel for Coal-Tar SubstrateA 127 by 254-mm(5 by 10-in.) piece cut from a standard roll of so-called “6.8-kg(15-lb) coal-tar saturated heat resistant or rag felt.” Unlessoth
12、erwise specified, use a Specification D227 coal tar saturatedfelt.5.3 Test Panel for Asphalt SubstrateA 127 by 254-mm (5by 10-in.) piece cut from a standard roll of 6.8-kg (15-lb)asphalt-saturated felt. Unless otherwise specified, use a Speci-fication D226 (Type 1) asphalt saturated felt.5.4 Paint C
13、omposition for Use as a ControlThe paintcomposition shown in Table 1 can be used as a control whenapplied to 6.8 kg (15 lb) felt. This formulation will show severebleeding when applied on a coal tar substrate and a somewhatlower degree of bleeding when applied on the asphalt feltsubstrate.1This prac
14、tice is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.44 on Traffic Coatings.Current edition approved June 1, 2015. Published June 2015. Originallyapproved in 1946. Last previous edition appr
15、oved in 2010 as D868 10. DOI:10.1520/D0868-10R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last ap
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD86820102015STANDARDPRACTICEFORDETERMINATIONOFDEGREEOFBLEEDINGOFTRAFFICPAINT 测定 路标 漆渗色 程度 标准 实施 规程
链接地址:http://www.mydoc123.com/p-512355.html