ASTM D1751-2018 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types).pdf
《ASTM D1751-2018 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types).pdf》由会员分享,可在线阅读,更多相关《ASTM D1751-2018 Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types).pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D1751 04 (Reapproved 2013)1D1751 18Standard Specification forPreformed Expansion Joint Filler for Concrete Paving andStructural Construction (Nonextruding and ResilientBituminous Types)1This standard is issued under the fixed designation D1751; the number immediately following the desig
2、nation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by
3、agencies of the U.S. Department of Defense.1 NOTEEditorially corrected 5.5 in September 2013.1. Scope1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery afterrelease from compression.1.2 The values stated in inch-pound units are
4、to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.NOTE 1Attention is called to SpecificationSpecifications D1752 and to Specification D994D994/D994M.1.3 The text of this standard
5、references notes and footnotes which provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be considered as requirements of the standard.1.4 This international standard was developed in accordance with internationally recognized principles on standa
6、rdizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D545 Test Methods for Preformed Expansion Joint F
7、illers for Concrete Construction (Nonextruding and Resilient Types)D994D994/D994M Specification for Preformed Expansion Joint Filler for Concrete (Bituminous Type)D1752 Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving andStructural Construct
8、ion3. Ordering Information3.1 Products conforming to this specification are manufactured in sheet form to a range of thicknesses;thicknesses, namely 14,38, 12, 34, and 1 in. Sheet sizes may be 3 or 4 ft in width and standard length of 10 ft. Purchaser must specify sheet sizes whenordering.3.2 Joint
9、filler in strip form is cut from the sheets as manufactured. When ordering joint filler strips, the purchaser must specifythickness, width, and length; strip widths are available from 2 in. in increments of one12 half inch.in.4. Material4.1 This product shall consist of preformed sheets or strips ma
10、de from cane or other suitable fibers of a cellulosic nature securelybound together and then uniformly saturated with asphalt; or, strips formed from clean granulated cork securely bound togetherby a suitable asphalt binder and encased between two layers of saturated felt or two layers of glass-fibe
11、r felt.1 This specification is under the jurisdiction ofASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.34 on PreformedJoint Fillers, Sealers and Sealing Systems.Current edition approved Sept. 1, 2013Oct. 1, 2018. Published November 2013October 20
12、18. Originally approved in 1983. Last previous edition approved in 2008 asD1751 04 (2008). DOI: 10.1520/D1751-04R13E01.10.1520/D1751-18.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume inf
13、ormation, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately
14、depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA
15、 19428-2959. United States14.2 Preformed strips of expansion joint filler shall be of such character as not to be deformed or broken by twisting, bending,or other ordinary handling when exposed to atmospheric conditions.5. Requirements5.1 Test SpecimenThe sample to be tested shall be cut from the sh
16、eet, as manufactured, and shall be representative of the sheetstock.5.2 CompressionThe stressload required to compress the test specimen to 50 % of its thickness before test shall be not lessthan 100 and not more than 750 psi (689 to 5171 kPa). If the nominal thickness of the specimen is less than 1
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD17512018STANDARDSPECIFICATIONFORPREFORMEDEXPANSIONJOINTFILLERFORCONCRETEPAVINGANDSTRUCTURALCONSTRUCTIONNONEXTRUDINGANDRESILIENTBITUMINOUSTYPESPDF
链接地址:http://www.mydoc123.com/p-510406.html