ASTM D1370 D1370M-2012(2016) Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test)《沥青材料间接触相容性的标准试验方法(奥林萨斯试验)》.pdf

《ASTM D1370 D1370M-2012(2016) Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test)《沥青材料间接触相容性的标准试验方法(奥林萨斯试验)》.pdf》由会员分享，可在线阅读，更多相关《ASTM D1370 D1370M-2012(2016) Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test)《沥青材料间接触相容性的标准试验方法(奥林萨斯试验)》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D1370/D1370M 12 (Reapproved 2016)Standard Test Method forContact Compatibility Between Asphaltic Materials (OliensisTest)1This standard is issued under the fixed designation D1370/D1370M; the number immediately following the designation indicates theyear of original adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method provides a means for evaluatingcontact compatibility between asphaltic

3、materials. It is gener-ally used to determine compatibility between the saturant andcoating used in the manufacture of prepared roofings.2Coatingand saturant will be referred to, but comparable asphalticmaterials may be tested where this test procedure seemsapplicable.1.2 The values stated in either

4、 SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard

5、does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM S

6、tandards:3E11 Specification for Woven Wire Test Sieve Cloth and TestSieves3. Summary of Test Method3.1 A small drop of molten saturant is placed on the freshlytalced surface of the coating, and compatibility is judged by thedegree to which an oily ring develops in the talc surroundingthe drop.24. Si

7、gnificance and Use4.1 This test method assesses the degree to which asphaltsinteract with one another. It can indicate possible futureproblems, especially blistering, in a roofing product if incom-patible asphalts are in contact in the product.5. Apparatus5.1 Container, lid of 85-g 3-oz ointment box

8、, or equivalentcontainer.5.2 Analytical Balance, having an accuracy of 61.0 mg.5.3 Sieve 45-m (No. 325). Detailed requirements for thesesieves are given in Specification E11.5.4 Dropping Device, a fine wire 1.0 mm 0.04 in. indiameter.5.5 Oven, constant-temperature, capable of maintaining thetest tem

9、perature within 61.0C 61.8F.5.6 Small Scale, graduated in 0.1 mm divisions.5.7 Magnifying Glass or Stereo Microscope, approximateminimum of 4.5.8 Talc, pure, of the soapstone variety, ground so that atleast 70 % passes the 45-m (No. 325) sieve, and oven-dried at110C 230F.NOTE 1When this test method

10、is being used in purchasespecifications, both the purchaser and the seller shall use the same talc.Talc from Luzenac America, Inc.4has been found to be suitable for thistest.6. Procedure6.1 Melt a portion of the coating at the minimum tempera-ture required to render it fluid, stirring with the fine

11、wire toeliminate bubbles, and pour it into the clean 85-g 3 oz tin lidto a thickness of 3.0 to 6.0 mm 18 to14 in. Pour carefully, soas to provide a substantially smooth surface free of bubbles andother surface blemishes. After the coating material has cooled,determine the weight and surface area of

12、the filled container.1This test method is under the jurisdiction ofASTM Committee D08 on Roofingand Waterproofing and is the direct responsibility of Subcommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved Nov. 1, 2016. Published November 2016. Originallyapproved in 1984

13、. Last previous edition approved in 2012 as D1370/D1370M 12.DOI: 10.1520/D1370_D1370M-12R16.2This test determines only exudative incompatibility. For application of thisprocedure to determination of insudative incompatibility, see “Compatibility Be-tween BitumensExudation versus Insudation,” by Olie

14、nsis, G. L., MaterialsResearch and Standards, Vol 1, No. 9, September 1961, p. 723.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary pa

15、ge onthe ASTM website.4The sole source of supply known to the committee at this time is the LuzenacAmerica, Inc., 9000 East Nichols Avenue, Englewood, CO, 80112. If you are awareof alternative suppliers, please provide this information to ASTM Headquarters.Your comments will receive careful consider

16、ation at a meeting of the responsibletechnical committee,1which you may attend.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.2 Make a preliminary dusting of talc by covering thecoating surface with talc and removing the excess, no

17、nadherentdust by inverting the container and dropping it approximately25 mm 1 in. onto the table top.6.3 Make a final application of talc through the 45-m (No.325) sieve, held 20 to 25 mm 34 to 1 in. above the surface ofthe coating, by gently shaking or tapping the sieve until asmooth, uniform film

18、of talc, weighing 0.004 g 6 10 % persquare centimetre, has been applied.6.4 Place 3 drops of molten saturant, each about 3.0 6 0.5mm 18 6164 in. in diameter, on the talced surface of thecoating. Form the drops by plunging the wire into the moltensaturant and, after the excess has drained off, allowi

19、ng suitablysized drops to fall on the talc from a sufficient height to formsubstantially spherical drops.6.5 Place the prepared specimen in the test oven, so regu-lated as to maintain the specimen at the recommended testtemperature, within 61.0C 61.8F, for 72 h (Note 2). Aftercooling, examine the sp

20、ecimen and measure any oily ringformed around the periphery of the drop, recording its width tothe nearest 0.1 mm. Measure the width from the line of contactof talc and drop to the outer limit of the oil ring.NOTE 2The recommended test temperature for roofing materials is50C 122F, but this may be al

21、tered to accommodate variations in thebitumens being tested, for example, when determining compatibility ofsealants, higher temperatures are appropriate.7. Report7.1 Report the results of the compatibility test as the widthin millimetres of the ring developed in the specified testtemperature.8. Prec

22、ision and Bias8.1 RepeatabilityDuplicate results by the same operatorshould not differ by more than 0.1 mm.8.2 ReproducibilityResults between laboratories shouldbe reproducible within 0.2 mm.9. Keywords9.1 asphaltic materials; coating asphalt; compatibility; con-tact; oliensis test; saturant asphalt

23、ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are

24、 entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standar

25、dsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committ

26、ee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 12 (2016)2