ASTM C629 C629M-2010 Standard Specification for Slate Dimension Stone《板岩规格料标准规格》.pdf

《ASTM C629 C629M-2010 Standard Specification for Slate Dimension Stone《板岩规格料标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C629 C629M-2010 Standard Specification for Slate Dimension Stone《板岩规格料标准规格》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C629/C629M 10Standard Specification forSlate Dimension Stone1This standard is issued under the fixed designation C629/C629M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parent

2、heses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers the material characteristics,physical requir

3、ements, and sampling appropriate to the selec-tion of slate for general building and structural purposes. Referto Guides C1242 and C1528 for the appropriate selection anduse of slate dimension stone.1.2 Dimension slate shall include stone that is sawed, cut,split, or otherwise finished or shaped, an

4、d shall specificallyexclude molded, cast, or otherwise artificially aggregated unitscomposed of fragments, and also crushed and broken stone.1.3 It specifically excludes roofing slate (see SpecificationC406/C406M) and slate for industrial uses.1.4 The values stated in either SI units or inch-pound u

5、nitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2

6、C119 Terminology Relating to Dimension StoneC120/C120M Test Methods of Flexure Testing of Slate(Breaking Load, Modulus of Rupture, Modulus of Elastic-ity)C121/C121M Test Method for Water Absorption of SlateC217/C217M Test Method for Weather Resistance of SlateC241/C241M Test Method for Abrasion Resi

7、stance ofStone Subjected to Foot TrafficC406/C406M Specification for Roofing SlateC1242 Guide for Selection, Design, and Installation ofDimension Stone Attachment SystemsC1353 Test Method for Abrasion Resistance of DimensionStone Subjected to Foot Traffic Using a Rotary Platform,Double-Head AbraserC

8、1528 Guide for Selection of Dimension Stone3. Terminology3.1 DefinitionsAll definitions are in accordance with Ter-minology C119.4. Classification4.1 Dimension slate shall be selected for the following uses:4.1.1 I Exterior.4.1.2 II Interior.5. Physical Requirements5.1 Slate supplied under this spec

9、ification shall conform tothe requirements listed in Table 1.5.2 Slate used for exterior applications in ambient acidicatmospheres or in industrial areas where heavy air pollutionoccurs shall be free of carbonaceous ribbons. Slate shall besound, durable, and free of spalls, cracks, open seams, pits,

10、 orother defects that are likely to impair its structural integrity inits intended use.5.3 Slate shall be selected for overall satisfactory andnatural appearance.5.4 The desired color and texture, with their permissiblenatural variations in material characteristics for all material tobe produced for

11、 the project, shall be established by controlsamples. Select representative samples by viewing a sufficientnumber of physical samples prior to production that show thecomplete range of variations in color and texture of the slatespecified.6. Sampling6.1 Samples, if required, for testing to determine

12、 the char-acteristics and physical properties shall be representative of theslate to be used.7. Keywords7.1 acid resistance; carbonaceous ribbons; slate1This specification is under the jurisdiction of ASTM Committee C18 onDimension Stone and is the direct responsibility of Subcommittee C18.03 onMate

13、rial Specifications.Current edition approved Sept. 1, 2010. Published October 2010. Originallyapproved in 1968. Last previous edition approved in 2008 as C629 08. DOI:10.1520/C0629-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm

14、.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity o

15、f any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to

16、 revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters.

17、Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is c

18、opyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm

19、.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Physical RequirementsNOTEThe values in Table 1 were established using samples prepared according to the individual test me

20、thods. Finishes, other than those specifiedin the individual test methods, may result in a deviation from established values.PropertyTest Require-mentsClassifications Test Method(s)Absorption, max, % 0.25 I Exterior C121/C121M0.45 II InteriorModulus of rupture,min, psi (MPa):Across grain 9000 62 I E

21、xterior C120/C120M7200 50 II InteriorAlong grain 7200 50 I Exterior5500 38 II InteriorAbrasion resistance, 8.0 I Exterior C241/C241M/C1353min, HaA,B,C8.0 II InteriorAcid resistance, max, 0.015 0.38 I Exterior C217/C217Min. mm 0.025 0.64 II InteriorAPertains only to stone subject to foot traffic.BThe

22、 supplier of the No. 60Alundum abrasive, Norton, has indicated that the formula for Norton treatment 138S has been changed. The new abrasive is currrently moreaggressive, resulting in lower abrasive hardness values (Ha) than when the standard was initially established. As such, care should be taken

23、when interpreting Havaluesfrom tests using the new abrasive, particularly with regard to currentASTM stone standard specification requirements for abrasion resistance, which were developed whenthe original abrasive was still in use. Committee C18 is actively studying alternatives to address this issue.CAbrasion Resistance Test Method C1353 will eventually replace Test Method C241/C241M and it is not necessary to perform both tests. Availability of the properequipment and materials by the testing laboratory may determine which test is performed.C629/C629M 102