ASTM C1658 C1658M-2012 Standard Specification for Glass Mat Gypsum Panels《玻璃纤维石膏板的标准规格》.pdf
《ASTM C1658 C1658M-2012 Standard Specification for Glass Mat Gypsum Panels《玻璃纤维石膏板的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1658 C1658M-2012 Standard Specification for Glass Mat Gypsum Panels《玻璃纤维石膏板的标准规格》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation:C1658/C1658M06 Designation: C1658/C1658M 12Standard Specification forGlass Mat Gypsum Panels1This standard is issued under the fixed designation C1658/C1658M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the year of
2、last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the glass mat gypsum panels described in 1.1.1-1.1.3.1.1.1 Glass mat interior gypsum panel,
3、designed for use on walls, ceilings, or partitions and that affords a surface suitable toreceive decoration.1.1.2 Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel, designed for use as a base in multilayersystems or as gypsum studs or cores in semisolid or solid gypsum board pa
4、rtitions, or in shaftwall assemblies.1.1.3 Glass mat water-resistant gypsum panel, designed to be used as a base for the application of ceramic or plastic tile on wallsor ceilings. This product is also suitable for decoration. (This is distinct from a coated glass mat water-resistant gypsum panelAST
5、M 1178.)1.2 Specifications applicable to all glass mat gypsum panels are located in Sections 1-4 and 8-10. Specifications applicable tospecific glass mat gypsum panels are located in the following sections:SectionGlass mat interior gypsum panel 5Glass mat coreboard gypsum panel,and glass mat shaftli
6、nergypsum panel6Glass mat water-resistant gypsum panel 71.3 The values stated in either inch-pound units or SI (metric) are to be regarded separately as standard. Within the text, the SIunits are shown in brackets. The values stated in each system shall be used independent of the other. Values from
7、the two systemsshall not be combined.2. Referenced Documents2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related Building Materials and SystemsC473 Test Methods for Physical Testing of Gypsum Panel ProductsC645 Specification for Nonstructural Steel Framing MembersC1264 Specification fo
8、r Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storageof Gypsum Panel ProductsE84 Test Method for Surface Burning Characteristics of Building MaterialsE119 Test Methods for Fire Tests of Building Construction and Materials3. Terminology3.1 Definitions u
9、sed in this specification shall be in accordance with Terminology C11.3.2 Definitions of Terms Specific to This Standard:3.2.1 glass mat, na mat of glass fibers with or without a binder.4. Materials and Manufacture4.1 Glass mat gypsum panel shall consist of a noncombustible core, essentially gypsum,
10、 surfaced with glass mat partially orcompletely embedded in the core.1This test method is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility ofSubcommittee C11.01 on Specifications and Test Methods for Gypsum Products.Cu
11、rrent edition approved Dec. 1, 2006. Published January 2007. DOI: 10.1520/C1658_C1658M-06.Current edition approved Jan. 15, 2012. Published March 2012. Originally approved in 2006. Last previous edition approved in 2006 as E841 06. DOI:10.1520/C1658_C1658M-12.2For referenced ASTM standards, visit th
12、e ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.1This document is not an ASTM standard and is intended only to provide the user of an ASTM standard
13、 an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is
14、 to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.1.1 Glass mat interior gypsum panel shall consist of a noncombustible core, essentially gypsum, surfaced on both the face andback with glass mat
15、 partially or completely embedded into the core.4.1.2 Glass mat coreboard gypsum panel, and glass mat shaftliner gypsum panel shall be either a single panel or composed oftwo factory-laminated gypsum panels to provide up to 1 in. 25.4 mm total nominal thickness, surfaced on both face and backwith gl
16、ass mat partially or completely embedded into the core.4.1.3 Glass mat gypsum water-resistant panel shall consist of a noncombustible water-resistant core, essentially gypsum,surfaced on the face with water-resistant glass mat partially or completely embedded into the core.4.2 Glass Mat Interior Gyp
17、sum panel, and Glass Mat Water-Resistant gypsum panel, type X (special fire-resistant) designatesglass mat gypsum panel complying with this specification that provide not less than 1 h fire resistance for panel58 in. 15.9 mmthick or34 h fire resistance for panel12 in. 12.7 mm thick, applied parallel
18、 with and on each side of load bearing 2 by 4 woodstuds spaced 16 in. 406 mm on center with 6d coated nails, 178 in. 48 mm long, 0.0915 in. 2.3 mm diameter shank,14 in.6.4 mm diameter heads, spaced 7 in. 178 mm on center with glass mat gypsum panel joints staggered 16 in. 406 mm on eachside of the p
19、artition and tested in accordance with Test Methods E119.NOTE 1Consult manufacturers for independent test data on assembly details and fire resistance classifications for other types of construction. See firetest reports or listings from recognized fire testing laboratories for assembly particulars,
20、 materials, and classifications.4.3 Glass Mat Shaftliner gypsum panel, type X, designates glass mat gypsum shaftliner panel complying with this specificationthat meets the acceptance criteria for temperature rise for not less than panels 1-in. 25.4 mm thick, when applied in a double layersolid non-l
21、oad bearing partition as described in 4.3.2 and tested in accordance with Test Methods E119 with thermocouplelocations as specified in 4.3.2.4.3.1 Two layers of glass mat gypsum shaftliner panel applied vertically and friction fit into vertical 25-gauge steel “H”members, 2-in. 50.8 mm deep for panel
22、s 1-in. 25.4 mm thick, spaced 24-in. 610 mm on centers and 25-gauge steel track atthe perimeter of the partition. “H” members shall be formed with a single web or shall be two pieces of perimeter track fastenedtogether along the web with screws spaced 24-in. 610 mm on centers.4.3.2 Temperature rise
23、on the unexposed surface shall be measured using not less than five thermocouples; one shall be locatedat the center of the assembly and one shall be located at the center of each quadrant. Thermocouples shall be located not less than3-in. 76 mm from an “H” member.4.4 Glass mat gypsum panels shall h
24、ave a flame spread index of not more than 25 when tested in accordance with Test MethodE84.4.5 Physical Properties, Dimensions, and Tolerances of Glass Mat Gypsum Panel:4.5.1 Specimens shall be taken from the samples obtained in accordance with Specification C1264.4.5.1.1 Specimens shall be tested i
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC1658C1658M2012STANDARDSPECIFICATIONFORGLASSMATGYPSUMPANELS 玻璃纤维 石膏板 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-465425.html