ASTM C1264-2005(2011) Standard Specification for Sampling Inspection Rejection Certification Packaging Marking Shipping Handling and Storage of Gypsum Board《石膏板的抽样 检查 报废 认证 包装 标记 海.pdf

《ASTM C1264-2005(2011) Standard Specification for Sampling Inspection Rejection Certification Packaging Marking Shipping Handling and Storage of Gypsum Board《石膏板的抽样 检查 报废 认证 包装 标记 海.pdf》由会员分享，可在线阅读，更多相关《ASTM C1264-2005(2011) Standard Specification for Sampling Inspection Rejection Certification Packaging Marking Shipping Handling and Storage of Gypsum Board《石膏板的抽样 检查 报废 认证 包装 标记 海.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1264 05 (Reapproved 2011)Standard Specification forSampling, Inspection, Rejection, Certification, Packaging,Marking, Shipping, Handling, and Storage of Gypsum PanelProducts1This standard is issued under the fixed designation C1264; the number immediately following the designation indi

2、cates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers sampling; inspec

3、tion; rejec-tion; certification; packaging and marking; and shipping, han-dling, and storage of gypsum panel products.2. Sampling2.1 When specified by the purchase agreement, samples ofgypsum panel products shall be taken at the place of manufac-ture or at the destination. If the samples are taken a

4、t thedestination, such samples shall be taken within 24 h of thereceipt of the material.2.2 At least 0.25 % of the number of gypsum panel productsin a shipment, but not less than three gypsum panel products,shall be so selected as to be representative of the shipment andshall constitute a sample for

5、 the purpose of tests by thepurchaser or user.3. Inspection3.1 Inspection of the gypsum panel products shall be agreedupon between the purchaser and the producer or supplier aspart of the purchase agreement.4. Rejection4.1 Rejection of gypsum panel products that fails to con-form to the requirements

6、 of the specification shall be reportedto the producer or supplier promptly and in writing. The noticeof rejection shall contain a statement documenting how thegypsum panel products has failed to conform to the require-ments of the specification.5. Certification5.1 When specified in the purchase agr

7、eement, a producersor suppliers report shall be furnished at the time of shipmentcertifying that the product is in compliance with the ASTMspecification referencing this specification.6. Packaging and Marking6.1 Unless otherwise specified in the purchase agreement,each gypsum panel product or packag

8、e shall have legiblymarked thereon the following: the thickness, the name of theproducer or supplier, the brand name, if any, and the ASTMspecification for the product.7. Shipping, Handling, and Storage7.1 Gypsum panel products shall be shipped so as to be keptdry.7.2 Gypsum panel products shall be

9、stored so as to be keptdry, preferably inside a building. Gypsum panel products shallbe neatly stacked flat with care taken to prevent sagging ordamage to edges, ends, and surfaces.7.3 Where necessary to store gypsum panel products out-side, it shall be stacked flat, off the ground, supported on a l

10、evelplatform, and fully protected from weather and direct sunlightexposure.8. Keywords8.1 certification; gypsum; gypsum panel products; handling;inspection; marking; packaging; rejection; sampling; shipping;storage1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Relat

11、ed Building Materials and Systems and is the direct responsibilityof Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.Current edition approved April 1, 2011. Published May 2011. Originallyapproved in 1994. Last previous edition approved in 2005 as C1264 05. DOI:10.1520/C126

12、4-05R11.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expr

13、essly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revise

14、d, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may

15、attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United State

16、s. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1264 05 (2011)2