ASTM C1177 C1177M-2013 Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing《用作防水层的玻璃纤维衬垫石膏基底标准规格》.pdf

《ASTM C1177 C1177M-2013 Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing《用作防水层的玻璃纤维衬垫石膏基底标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1177 C1177M-2013 Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing《用作防水层的玻璃纤维衬垫石膏基底标准规格》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1177/C1177M 08C1177/C1177M 13Standard Specification forGlass Mat Gypsum Substrate for Use as Sheathing1This standard is issued under the fixed designation C1177/C1177M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision,

2、the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers glass mat gypsum substrate, which is designed to be used as an exterior substra

3、te for a weatherbarrier.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI unitsare shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be usedindependently of the

4、other. Combining values from the two systems may result in non-conformance with the standard.1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be considered as requirements of the

5、 standard.2. Referenced Documents2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related Building Materials and SystemsC22 Specification for GypsumC473 Test Methods for Physical Testing of Gypsum Panel ProductsC645 Specification for Nonstructural Steel Framing MembersC1264 Specification f

6、or Sampling, Inspection, Rejection, Certification, Packaging, Marking, Shipping, Handling, and Storage ofGypsum Panel ProductsE119 Test Methods for Fire Tests of Building Construction and Materials3. Terminology3.1 Definitions shall be in accordance with Terminology C11.3.2 Definitions of Terms Spec

7、ific to This Standard:3.2.1 glass mat, na mat of glass fibers with or without a binder.3.2.2 edge, nthe bound edge as manufactured.3.2.3 weather barrier, na material that prevents the passage of rain, sleet and snow.4. Materials and Manufacture4.1 Glass Mat Gypsum Substrate shall consist of a noncom

8、bustible water-resistant core, essentially gypsum, gypsum complyingwith Specification C22, surfaced with glass mat partially, or completely embedded in the core.4.2 Glass Mat Gypsum Substrate, type X (special fire-resistant) designates glass mat gypsum substrate complying with thisspecification that

9、 provide not less than 1-h fire resistance rating for substrate 58 in. 15.9 mm thick or 34-h fire resistance ratingfor substrate 12 in. 12.7 mm thick, applied parallel with and on each side of load bearing 2 by 4 wood studs spaced 16 in. 406mm on center with 6d coated nails, 1 78 in. 48 mm long, 0.0

10、915 in. 2.3 mm diameter shank, 14 in. 6.4 mm diameter heads,spaced 7 in. 178 mm on center with glass mat gypsum substrate joints staggered 16 in. 406 mm on each side of the partitionand tested in accordance with Test Methods E119.NOTE 1Consult manufacturers for independent test data on assembly deta

11、ils and fire resistance ratings for other types of construction. See fire test1 This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility ofSubcommittee C11.01 on Specifications and Test Methods for Gypsum

12、 Products.Current edition approved Sept. 15, 2008Oct. 1, 2013. Published October 2008 October 2013. Originally approved in 1991. Last previous edition approved in 20062008as C11C1177/C1177M77/C 1177M06.08. DOI: 10.1520/C1177_C1177M-08.10.1520/C1177_C1177M-13.2 For referencedASTM standards, visit the

13、ASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an

14、indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to

15、be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1reports or listings from recognized fire testing laboratories for assembly particular

16、s, materials, and ratings.5. Physical Properties5.1 Specimens shall be taken from the samples obtained in accordance with Specification C1264.5.2 Specimens shall be tested in accordance with Methods C473.5.2.1 Flexural StrengthThe specimens shall be tested face up and face down. The average breaking

17、 load shall not be less thanthe following:Method BThickness,in. mmLoad, lbf N Bearingedges perpendicular tothe substrate edgeLoad, lbf N Bearing edgesparallel to the substrateedge14 6.4 50 222 40 178716 11.1 88 394 70 31412 12.7 100 445 80 35658 15.9 140 623 100 445C1177/C1177M 1325.2.2 Humidified D

18、eflectionSpecimens shall have an average deflection of not more than the following:Thickness,in. mmHumidified deflection,eighths of an in. mm14 6.4 not required716 11.1 3 912 12.7 2 658 15.9 1 35.2.3 Core, End and Edge HardnessSpecimens shall have an average hardness of not less than 15 lbf 67 N whe

19、n tested inaccordance with Method B:5.2.4 Nail Pull ResistanceSpecimens shall have an average nail pull resistance of not less than the following when tested inaccordance with Method B:Thickness,in. mmNail pull resistance,lbf N14 6.4 40 178716 11.1 70 31412 12.7 80 35658 15.9 90 4005.2.5 Water Resis

20、tanceThe three specimens selected shall have an average water absorption of not more than 10 weight %after a 2-h immersion.6. Dimensions and Tolerances6.1 Specimens shall be taken from the samples obtained in accordance with Specification C1264.6.2 Thickness, width, length and end squareness shall b

21、e determined in accordance with Test Methods C473.6.2.1 ThicknessThe nominal thickness shall be 14, 716,12, or 58 in. 6.4, 11.1, 12.7 or 15.9 mm, with tolerances in the nominal thickness of 6 132 in. 6 0.8 mm, and with localvariations of 6 116 in. 6 1.6 mm from the nominal thickness.6.2.2 WidthThe n

22、ominal width shall be up to 48 in. 1220 mm, with tolerance of 18 in. 3 mm under the specified width.6.2.3 LengthThe tolerance in length shall be 6 14 in. 6 6 mm6.2.4 End SquarenessCorners shall be square with a tolerance of 6 18 in. 6 3 mm in the full width of the substrate.6.3 Edges and EndsThe edg

23、es and ends shall be straight and either square, beveled, featured, tapered, or featured and tapered.7. Finish and Appearance7.1 Glass mat gypsum substrate shall be free of any cracks and imperfections that would render it unfit for its designed use.8. Sampling, Inspection, Rejection, Certification,

24、 Packaging, Marking, Shipping, Handling, and Storage8.1 Shall be in accordance with Specification C1264.9. Keywords9.1 core; exterior substrate; fire-resistant classification; flexural strength; glass mat; glass mat gypsum substrate; gypsum;hardness; humidified deflection; nail pull resistance; nonc

25、ombustible; sheathing; substrate; type X; water resistance; weatherbarrierAPPENDIX(Nonmandatory Information)This Appendix gives general information and also suggestions for inclusions to be made elsewhere by the specifier. They arenot part of this specification.This Appendix gives general informatio

26、n and also suggestions for inclusions to be made elsewhere by the specifier. They are not part of this specification.The definitions of type X as given in 4.2 and the alternate definition given in this appendix, are intended only as a test to define glass mat gypsum substrate for useas sheathing as

27、meeting the requirements of type X. These tests do not indicate a preferred application nor do they limit the use of the product in other fire relatedassemblies.All gypsum panel products for which type X is defined, except gypsum lath and gypsum shaftliner board, use the same test for type X product

28、s, therefore the type Xdesignation indicates a consistent level of fire resistance.C1177/C1177M 133The definitions of type X as given in 4.2 and the alternate definition given in this appendix, are intended only as a test to de-fine glass mat gypsum substrate for use as sheathing as meeting the requ

29、irements of type X. These tests do not indicate a pre-ferred application nor do they limit the use of the product in other fire related assemblies.All gypsum panel products for which type X is defined, except gypsum lath and gypsum shaftliner board, use the same testfor type X products, therefore th

30、e type X designation indicates a consistent level of fire resistance.C1177/C1177M 134X1. ALTERNATE DEFINITION FOR TYPE XX1.1 Glass mat gypsum substrate, type X (special fire-resistant) designates glass mat gypsum substrate providing a greater fireresistance than regular glass mat gypsum substrate of

31、 the same thickness. Type X (special fire-resistant) glass mat gypsumsubstrate, when tested in accordance with Test Methods E119, shall provide the following minimum fire resistance ratings for theassemblies described:X1.1.1 One hour for a 58 in. 15.9 mm thickness applied to a partition in a single

32、layer application on each side of 358 in. 92mm deep non-loadbearing galvanized steel studs complying with Specification C645 spaced 24 in. 610 mm on center. The 58in. 15.9 mm thick glass mat gypsum substrate 48 in. 1220 mm wide shall be attached using 1 in. 25 mm long drywall screwsspaced 8 in. 203

33、mm on center along the edges and ends, and 12 in. 305 mm along intermediate studs. All joints shall beoriented parallel to and located over studs and staggered on opposite sides of the assembly; andX1.1.2 Two hours for a 12 in. 12.7 mm thickness applied to a partition in a double layer application o

34、n each side of 212 in. 64mm deep non-loadbearing galvanized steel studs complying with Specification C645 spaced 24 in. 610 mm on center. The baselayer 48 in. 1220 mm wide shall be attached using 1 in. 25 mm long drywall screws spaced 12 in. 305 mm on center alongsubstrate edges, ends and along inte

35、rmediate studs. Joints shall be oriented parallel to and located over studs and staggered onopposite sides of the assembly. The face layer 48 in. 1220 mm wide shall be attached using 158 in. 41 mm long drywall screwsspaced 12 in. 305 mm along substrate edges, ends and along intermediate studs. Joint

36、s shall be oriented parallel to and locatedover studs, offset 24 in. 610 mm from the base layer joints, and staggered on opposite sides of the assembly.SUMMARY OF CHANGESCommittee C11 has identified the location of selected changes to this specification since the last issue,C11C1177/C1177M 0877/C 11

37、77M 06, that may impact the use of this specification. (Approved Oct. 1,2013September 15, 2008) )(1) Revised 6.2.3.(1) Revised 2.1 and 4.1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this s

38、tandard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years

39、andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee,

40、 which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-29

41、59,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1177/C1177M 135