ASTM C1032-2014 Standard Specification for Woven Wire Plaster Base《铁丝钢抹灰底层的标准规格》.pdf

《ASTM C1032-2014 Standard Specification for Woven Wire Plaster Base《铁丝钢抹灰底层的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1032-2014 Standard Specification for Woven Wire Plaster Base《铁丝钢抹灰底层的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1032 06 (Reapproved 2011)C1032 14Standard Specification forWoven Wire Plaster Base1This standard is issued under the fixed designation C1032; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers woven wire plaster base, flat or self-furring, with or without stiffener wires, and with or withoutbacking

3、, designed for use as a base to receive gypsum or portland cement based plaster.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents of inch-pound units areapproximate.standard. The values given in parentheses are mathematical conversions to SI units that

4、are provided for informationonly and are not considered standard.1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be considered as requirements of the standard.2. Referenced Doc

5、uments2.1 ASTM Standards:2A641/A641M Specification for ZincCoated (Galvanized) Carbon Steel WireC11 Terminology Relating to Gypsum and Related Building Materials and Systems2.2 Federal Specifications:UU-B-790a Building Paper, Vegetable Fiber: Kraft, Waterproofed, Water Repellent and Fire Resistant3U

6、U-P-31 B/171 Tensile Breaking Strength (Dry)33. Terminology3.1 DefinitionsDefinitions shall be in accordance with Terminology C11.4. Material4.1 In accordance with Specification A641/A641M and Table 1.4.2 Kraft Building Paper, Federal Specification UU-B-790a.5. Physical Properties5.1 Backing:5.1.1 F

7、actory attached backing shall provide a one mesh wire to wire lap joint at one end and one edge of each flat sheet orroll.Attachment of the backing shall allow lapping of wire-to-wire and backing-to-backing of one mesh at ends and edges and shallpermit full embedment in not less than 14 in. (6.4 mm)

8、 of plaster of not less than one half the total length and width of the wire.5.1.2 Backing shall have a minimum tensile breaking strength (dry) of 20 lbf/in. (3.5 kN/m) width, as tested in accordance withFederal Specification UU-P-31 B, Method 171.6. Dimensions, Weight, and Permissible Variations6.1

9、 Openings:1 This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systems and is the direct responsibility ofSubcommittee C11.02 on Specifications and Test Methods for Accessories and Related Products.Current edition approved Dec. 1, 2011June

10、 1, 2014. Published June 2012June 2014. Originally approved in 1985. Last previous edition approved in 20062011 asC1032 06.C1032 06 (2011). DOI: 10.1520/C1032-06R11. 10.1520/C1032-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.o

11、rg. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 .Available from U.S. Government Printing Office Superintendent of Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.This documen

12、t is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as app

13、ropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United St

14、ates16.1.1 Woven wire plaster base shall be fabricated to provide the size of openings in accordance with Table 1, except that anysingle opening shall be not more than 3.0 in.2 (1935.5 mm2).6.1.2 Wire diameter for opening size shall be in accordance with Table 1.6.2 Diameter tolerance for galvanized

15、 wire shall be in accordance with Specification A641/A641M.6.3 The wire shall be zinc-coated (galvanized) in accordance with Specification A641/A641M.6.4 Weight for woven wire plaster base shall be in accordance with Table 1.6.5 When included as part of the woven wire plaster base, factory fabricate

16、d stiffener wires shall have a diameter not less thanthat specified in Table 1 and shall be continuous, parallel to the long dimension of the plaster base, and shall occur at not morethan 6-in. (154.4-mm) intervals.6.6 Factory fabricated crimps for self-furring woven wire plaster base shall provide

17、a nominal 14-in. (6.4-mm) separationbetween the back plane of the plaster base and the surface of solid backing to permit embedment in both directions.6.7 Width of woven wire plaster base shall be not less than 36 in. (914 mm).6.8 Length of woven wire plaster base shall be in accordance with Table 2

18、.7. Inspection7.1 Inspection of the material shall be agreed upon between the purchaser and the producer or supplier as part of the purchaseagreement.8. Rejection and Rehearing8.1 Material that fails to conform to the requirements of this specification shall be reported to the producer or supplier p

19、romptlyand in writing. The notice of rejection shall contain a statement documenting how the product has failed to conform to therequirements of the specification.9. Certification9.1 When specified in the purchase order or contract, the producer or supplier shall furnish a report certifying that at

20、the timeof shipment, the materials were in compliance with the requirements of this specification.10. Packaging and Package Marking10.1 PackagingWoven wire plaster base shall be packaged in bundles, rolls or pallets.10.2 MarkingWhen shipped for sale or resale, the Unless otherwise required by the pu

21、rchase agreement, lath shall havelegibly marked thereon the following: the product description; the name of the producer or the supplier and the brand anddescription of the contents shall be legibly marked on each pallet, bundle or roll. The quantity for bundles shall be square yardsand number of sh

22、eet per bundle. The quantity for pallets, bundles or rolls shall indicate the mesh-opening size and wirethickness.manufacturer or distributor, country of origin and contact information; the brand name (if any); and the ASTMdesignation for the product.10.2.1 Each bundle or roll of lath with no backin

23、g shall be marked with metal or paper tags securely attached to the bundlesor with metal tags, paper tags, plastic or metal banding or paper wrapping on rolls.10.2.2 Each flat sheet and roll of lath with backing shall be marked on the backing material.10.2.3 The quantity for flat sheet bundles shall

24、 be square yards and number of sheets per bundle marked with metal or papertags on the pallet or bundle. Rolls shall be marked with metal tags, paper tags, plastic or metal banding or paper wrapping on rolls.The marking for flat sheets and rolls shall indicate the mesh-opening size and wire thicknes

25、s of rolls.TABLE 1 Nominal Diameter and Minimum Weight for Size ofOpeningOpening Size,in. (mm)Diameter,in. (mm)Weight,lb/yd2 (kg/m2)A1 (25.4) 0.035 (0.89) 0.86 (0.466)112 (38.0) 0.051 (1.30) 1.40 (0.760)A The weight of attached backing is not included.TABLE 2 Minimum Length of Flat Sheets and RollsA

26、Flat Sheets 100 linear in. (2.540 m)Rolls 150 linear ft. (45.72 m)Rolls, with backing 100 linear ft. (30.48 m)A Allowable variations shall be not more than 34 in. (19.0 mm) in width or length.C1032 14211. Keywords11.1 backing; base; cement plaster; flat; gypsum plaster; plaster; self-furning; woven

27、wireSUMMARY OF CHANGESCommittee C11 has identified the location of selected changes to this specificationstandard since the last issue,issue (C1032 04C103206(2011),) that may impact the use of this specification.standard. (Approved June 1,2006)2014.)(1) Combined Tables 1 and 2 into new Table 1.(1) R

28、evised section 10.2.(2) Added new sections 10.2.1, 10.2.2, and 10.2.3.(2) Changed references to old Tables 1 and 2 to new Table 1within the text of the specification.C1032 143(3) Renumbered Table 3 as Table 2.ASTM International takes no position respecting the validity of any patent rights asserted

29、in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the

30、responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive car

31、eful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Internation

32、al, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1032 144