ASTM B698-2002 Standard Classification for Seamless Copper and Copper Alloy Plumbing Pipe and Tube《无缝铜和铜合金管和管道的标准分类》.pdf

《ASTM B698-2002 Standard Classification for Seamless Copper and Copper Alloy Plumbing Pipe and Tube《无缝铜和铜合金管和管道的标准分类》.pdf》由会员分享，可在线阅读，更多相关《ASTM B698-2002 Standard Classification for Seamless Copper and Copper Alloy Plumbing Pipe and Tube《无缝铜和铜合金管和管道的标准分类》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 698 02Standard Classification forSeamless Copper and Copper Alloy Plumbing Pipe andTube1This standard is issued under the fixed designation B 698; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope *1.1 This classification covers various types of seamlesscopper and copper alloy2pipe and tube used for water service,distributio

3、n, and drainage. It is not a specification for thevarious types and alloys.1.2 This classification uses the standard copper designationsdeveloped and used by the copper industry.1.3 This classification makes no attempt to differentiatebetween all compositions that could be termed coppers orcopper al

4、loys, but, in conformance with general practice in thetrade includes those coppers and copper alloys commonly usedin the manufacture of water service, distribution, and drainagepipe and tube.1.4 This classification makes no attempt to differentiatebetween all applications of seamless copper and copp

5、er alloypiping and tubing, and is intended for use in water servicedistribution and drainage.2. Referenced Documents2.1 ASTM Standards:B 42 Specification for Seamless Copper Pipe, StandardSizes3B 43 Specification for Seamless Red Brass Pipe, StandardSizes3B 88 Specification for Seamless Copper Water

6、 Tube3B 88M Specification for Seamless Copper Water TubeMetric3B 302 Specification for Threadless Copper Pipe3B 306 Specification for Copper Drainage Tube (DWV)3B 846 Terminology for Copper and Copper Alloys3E 527 Practice for Numbering Metals and Alloys (UNS)43. Terminology3.1 Definitions:3.1.1 The

7、 following definitions are used for purposes ofclassification:3.1.1.1 pipe, seamless, na seamless tube conforming tothe particular dimensions commercially known as StandardPipe Sizes.3.1.1.2 threadless pipe, na seamless tube conforming toparticular dimensions commercially known as Threadless Pipe(TP

8、).3.1.1.3 tube, seamless, na tube produced with a continu-ous periphery in all stages of the operation.3.1.1.4 tube, seamless water, na tube conforming to theparticular dimensions of tube commercially known as copperwater tube and designated as Types K, L, and M in inch-poundunits and Types A, B, an

9、d C in SI units.3.2 For definitions of general terms related to copper andcopper alloys, refer to Terminology B 846.4. Significance and Use4.1 This classification is provided to serve the needs ofdesigners, specifiers, installers, and users of seamless copperand copper alloy plumbing tube and piping

10、 systems. It famil-iarizes them with the products available for such systems,giving size ranges and available materials for products listedherein. Also refer to Section 1.5. Basis of Classification5.1 Tables 1 and 2 list ASTM specifications, types, desig-nations, general applications, range of sizes

11、 of water tubesproduced currently, and the copper or copper alloy UNSnumber. The listed products are not necessarily available in thecomplete range of coppers and alloys or sizes, nor from anyone supplier in all forms.5.2 Existing ASTM specifications for seamless copper andcopper alloys may cover mo

12、re than one of the products listedin Table 1.5.3 Table 3 contains the UNS numbers, previous designa-tions, and chemical composition of the coppers and copperalloys listed in Tables 1 and 2.6. Keywords6.1 copper; copper alloy; pipe; plumbing; seamless; tube1This classification is under the jurisdicti

13、on of ASTM Committee B05 onCopper and Copper Alloys and is the direct responsibility of Subcommittee B05.04on Pipe and Tube.Current edition approved Oct. 10, 2002. Published November 2002. Originallypublished as B 698 81. Last previous edition B 698 97.2The UNS system for copper and copper alloys (s

14、ee Practice E 527) is a simpleexpansion of the former standard designation system accomplished by the additionof a prefix “C” and a suffix “00.” The suffix can be used to accommodatecomposition variations of the base alloy.3Annual Book of ASTM Standards, Vol 02.01.4Annual Book of ASTM Standards, Vol

15、 01.01.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.SUMMARY OF CHANGESCommittee B05 has identified the location of selected changes to this standard since the last

16、issue (B 698 - 97)that may impact the use of this standard.(1) Reference to B 88M was removed from Table 1 andincluded in new Table 2.(2) Terminology B 846 was added to Section 2 and to the newsection 3.2.(3) Reference to SI Units was removed from Table 1 andincluded in new Table 2.(4) Alloys C10800

17、 and C12000 deleted from Table 1 for B302.(5) Oxygen limit added for Alloy C10200 in Table 2.(6) Phosphorus range corrected for Alloy C10300 in Table 2.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Us

18、ers of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed ever

19、y five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible techni

20、cal committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocke

21、n, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Classification for Se

22、amless Copper and Copper Alloy Plumbing Pipe and TubeASTMSpecificationType Designation ApplicationStandard MillSizes, in.Copper or Copper Alloy, UNS No.C10200 C10300 C10800 C12000 C12200 C23000B 42 Seamless copper pipe plumbing and feed lines1812 X X X X XB 43 Seamless red brass pipe plumbing and fe

23、ed lines1812 XB 88 Seamless K, L, M general plumbing water tube1412 XB 302 Seamless TP plumbing and feed lines1412 X XB 306 Seamless DWV drainage, waste, vent 1148 XTABLE 2 Classification for Seamless Copper Plumbing Tube (SI Units)ASTMSpecificationType Destination Application Standard MillSizes, mm

24、Copper or CopperAlloy, UNS No.B 88M Seamless A, B, C General plumbing water tube 6308 C12200TABLE 3 Alloy Designation and Chemical CompositionACopper or CopperAlloy UNS No.Previously UsedDesignationComposition, max, % (Unless Shown as a Range or Minimum)Copper, inclSilver (% min)Phosphorus Iron Lead

25、 ZincOther NamedElementsC10200BOF 99.95 . . . . 0.0010OxygenC10300 OFXLP 99.95C0.0010.005 . . . .C10800 OFLP 99.95C0.0050.012 . . . .C12000 DLP 99.90 0.0040.012 . . . .C12200DDHP 99.9 0.0150.040 . . . .C23000ERed brass, 85 % 84.086.0 . 0.05 0.05 remainderF.ARefer to the referenced product specificat

26、ion for details of chemical requirements.BThis is a high-conductivity copper that has in the annealed condition a minimum conductivity of 100 % IACS.CIncludes phosphorus.DThis includes oxygen-free copper that contains phosphorus in an amount agreed upon.EFor copper alloys in which zinc is specified

27、as the remainder, either copper or zinc may be taken as the difference between the sum of all the elements analyzed and100 %. When all the elements in Table 3 are analyzed, their sum shall be 99.8 % minimum.FThese specification limits do not preclude the presence of other elements. Limits for unnamed elements may be established by agreement between manufacturer orsupplier and purchaser.B698022