ASTM B516-2003(2009) Standard Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600 UNS N06603 UNS N06025 and UNS N06045 Tubes《焊接镍铬铁合金(UNS N06603、UNS N06025和UNS N06045)管的.pdf
《ASTM B516-2003(2009) Standard Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600 UNS N06603 UNS N06025 and UNS N06045 Tubes《焊接镍铬铁合金(UNS N06603、UNS N06025和UNS N06045)管的.pdf》由会员分享,可在线阅读,更多相关《ASTM B516-2003(2009) Standard Specification for Welded Nickel-Chromium-Iron Alloy (UNS N06600 UNS N06603 UNS N06025 and UNS N06045 Tubes《焊接镍铬铁合金(UNS N06603、UNS N06025和UNS N06045)管的.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B 516 03 (Reapproved 2009)Standard Specification forWelded Nickel-Chromium-Iron Alloy (UNS N06600, UNSN06603, UNS N06025, and UNS N06045) Tubes1This standard is issued under the fixed designation B 516; the number immediately following the designation indicates the year oforiginal adopt
2、ion or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers welded UNS N06600*,N06603, N06025, and N06045 a
3、lloy boiler, heat exchanger,and condenser tubes for general corrosion resisting and low orhigh-temperature service.1.2 This specification covers tubes18 to 5 in. (3.18 to 127mm), inclusive, in outside diameter and 0.015 to 0.500 in. (0.38to 12.70 mm), inclusive, in wall thickness. Table 2 of Specifi
4、-cation B 751 lists the dimensional requirements of these sizes.Tubes having other dimensions may be furnished providedsuch tubing complies with all other requirements of thisspecification.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are ma
5、thematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards in
6、cluding those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:
7、2B 751 Specification for General Requirements for Nickeland Nickel Alloy Welded TubeB 899 Terminology Relating to Non-ferrous Metals andAlloys3. Terminology3.1 Terms defined in Terminology B 899 shall apply unlessdefined otherwise in this standard.4. Ordering Information4.1 It is the responsibility
8、of the purchaser to specify allrequirements that are necessary for the safe and satisfactoryperformance of material ordered under this specification.Examples of such requirements include, but are not limited to,the following:4.1.1 Quantity (feet or number of lengths),4.1.2 UNS number,4.1.3 Size (out
9、side diameter minimum or average wallthickness),4.1.4 Length (random or specific),4.1.5 Class,4.1.6 ASTM designation,4.1.7 Product AnalysisState if required,4.1.8 CertificationState if a certification or a report of testresults is required, and4.1.9 Purchaser InspectionState which tests or inspec-ti
10、ons are to be witnessed, if any.5. Material and Manufacture5.1 Tube shall be made from flat-rolled alloy by an auto-matic welding process with no addition or filler metal. Subse-quent to welding and prior to final annealing, the material shallbe cold-worked in either the weld metal only or both weld
11、 andbase metal.5.2 Tube shall be furnished with oxide removed. Whenbright annealing is used, descaling is not necessary.6. Chemical Composition6.1 The material shall conform to the composition limitsspecified in Table 1. One test is required for each lot as definedin Specification B 751.1This specif
12、ication is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved April 15, 2009. Published April 2009. Originallyapproved in 1970. Last previous edition
13、 approved in 2003 as B 516 - 03.* New designation established in accordance with ASTM E 527 and SAE J1086,Practice for Numbering Metals and Alloys (UNS).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMSt
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB51620032009STANDARDSPECIFICATIONFORWELDEDNICKELCHROMIUMIRONALLOYUNSN06600UNSN06603UNSN06025ANDUNSN06045TUBES

链接地址:http://www.mydoc123.com/p-461452.html