ASTM A965 A965M-2014 Standard Specification for Steel Forgings Austenitic for Pressure and High Temperature Parts《压力和高温零件用奥氏体钢锻件的标准规格》.pdf

《ASTM A965 A965M-2014 Standard Specification for Steel Forgings Austenitic for Pressure and High Temperature Parts《压力和高温零件用奥氏体钢锻件的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A965 A965M-2014 Standard Specification for Steel Forgings Austenitic for Pressure and High Temperature Parts《压力和高温零件用奥氏体钢锻件的标准规格》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A965/A965M 13A965/A965M 14Standard Specification forSteel Forgings, Austenitic, for Pressure and HighTemperature Parts1This standard is issued under the fixed designation A965/A965M; the number immediately following the designation indicates the yearof original adoption or, in the case

2、of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers austenitic stainless steel forgings for boilers, pressure vessels,

3、 high temperature parts, andassociated equipment.1.2 Supplementary requirements are provided for use when additional testing, inspection, or processing is required. In addition,supplementary requirements from Specification A788/A788M may be specified when appropriate.1.3 This specification includes

4、the austenitic steel forgings that were a part of Specification A336/A336M.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the o

5、ther. Combining values from thetwo systems may result in non-conformance with the standard.1.5 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-poundunits.1.6 This standard does not purport to address all of the safety concerns, if

6、any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A336/A336M Specification for Alloy Steel Forgings f

7、or Pressure and High-Temperature PartsA370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA745/A745M Practice for Ultrasonic Examination of Austenitic Steel ForgingsA788/A788M Specification for Steel Forgings, General RequirementsA1058 Test Methods for Mechanical Testing of Ste

8、el ProductsMetricE112 Test Methods for Determining Average Grain Size2.2 Other Standards:ASME Boiler and Pressure Vessel Code, including Section VIII Pressure Vessels and Section IX33. Ordering Information and General Requirements3.1 In addition to the ordering information required by Specification

9、A788/A788M, the intended use should be stated if 5.1 isto be applicable.3.2 Material supplied to this specification shall conform to the requirements of Specification A788/A788M, which outlinesadditional ordering information, manufacturing requirements, testing and retesting methods and procedures,

10、marking, certification,product analysis variations, and additional supplementary requirements.1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01.06on Steel Forgings and Billets.Current e

11、dition approved Oct. 1, 2013May 1, 2014. Published November 2013May 2014. Originally approved in 1996. Last previous edition approved in 20122013 asA965/A965M 12.A965/A965M 13. DOI: 10.1520/A0965_A0965M-13.10.1520/A0965_A0965M-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, o

12、r contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, ThreeTwo Park Ave., New York, NY

13、 10016-5990,http:/www.asme.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommen

14、ds that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700,

15、West Conshohocken, PA 19428-2959. United States13.3 If the requirements of this specification are in conflict with the requirements of Specification A788/A788M, therequirements of this specification shall prevail.3.4 If the forgings are intended for use under the ASME Boiler and Pressure Vessel Code

16、 at temperatures exceeding 1000F540C, then use Supplementary Requirement S7. Grain size requirements for service exceeding 1000F 540C should bespecified unless the required grade has the suffix “H.”4. Melting and Forging4.1 In addition to the melting and forging requirements of Specification A788/A7

17、88M, which may include SupplementaryRequirement S8, the following condition applies:4.1.1 A sufficient discard shall be made to secure freedom from injurious pipe and undue segregation.5. Machining5.1 Forged pressure vessels for steam power service shall have the inner surface machined or ground. Un

18、fired pressure vesselsshall have the inner surfaces sufficiently free of scale to permit inspection.5.2 When rough machining is performed, it may be done either before or after heat treatment.6. Heat Treatment6.1 Forgings shall be furnished in the solution treated condition. On completion of forging

19、 operations, the forgings shall besolution annealed and quenched in water, oil, or a polymer water solution. Direct quenching after completion of forging withoutsubsequent reheating to the temperatures prescribed in 6.2 6.5 is not permissible.6.2 For Grades F304H, F309H, F310H, F316H, F321H, F347H,

20、and F 348H, the minimum solution annealing temperature shallbe 1925F 1050C.6.3 Grades FXM-11 and FXM-19 shall be solution annealed at 1950F 1065C.6.4 Grade F46 shall be solution annealed in the temperature range of 2010 to 2140F 1100 to 1170C.6.5 The remaining grades in Table 1 shall be solution ann

21、ealed at a minimum temperature of 1900F 1040C.7. Chemical Composition7.1 Heat AnalysisThe heat analysis obtained from sampling in accordance with Specification A788/A788M shall comply withTable 1.7.2 Product AnalysisThe manufacturer shall use the product analysis provision of Specification A788/A788

22、M to obtain aproduct analysis from a forging representing each heat or multiple heat. The product analysis tolerances for carbon shall not apply,and the carbon requirements shall conform to Table 1.7.3 Types (common names) and UNS designations follow:Grade Type UNS DesignationF304 304 S30400F304H 30

23、4H S30409F304L 304L S30403F304N 304N S30451F304LN 304LN S30453F309H 309H S30909F310 310 S31000F310H 310H S31009F316 316 S31600F316H 316H S31609F316L 316L S31603F316N 316N S31651F316LN 316LN S31653F70 . S31730F321 321 S32100F321H 321H S32109F347 347 S34700F347H 347H S34709F347LN 347LN S34751F348 348

24、S34800F348H 348H S34809FXM-19 XM19 S20910FXM-11 XM11 S21904F46 . S30600A965/A965M 1428. Mechanical Properties8.1 RequirementsThe material shall conform to the requirements for mechanical properties prescribed in Table 2 or, ifapplicable, Supplementary Requirement S2. The largest obtainable tension t

25、est specimen as specified in Test Methods andDefinitions A370 or Test Methods A1058 shall be used.8.2 Number of TestsThe number and location of tests are based on the heat-treated weight of the forging(s) from the same heat,solution annealed in the same furnace charge.8.2.1 For forgings weighing les

26、s than 5000 lb 2250 kg as heat treated, one tension test shall be required on the basis of onetest per heat in each heat treatment load. This test shall be taken from a prolongation of one of the forgings. Use of a separatelyforged test bar for the mechanical test specimens, instead of an integral p

27、rolongation, is acceptable for forgings weighing less than5000 lb 2250 kg, provided that the heat-treated cross section of the test bar is not less than the maximum heat-treated cross sectionof the forgings it represents. The separately forged test bar shall be from the same heat as the forgings it

28、represents and shallaccompany the forgings during heat treatment.8.2.2 When heat treatment is performed in continuous type furnaces equipped with recording pyrometers, such that completeheating records are available, a solution annealing charge may be considered as any continuous run not exceeding a

29、n 8 h period.8.2.3 For forgings weighing over 5000 lb 2250 kg, as heat treated, one tension test shall be taken from a prolongation on eachforging.8.3 The longitudinal axis of the tension test specimen shall be parallel to the direction of major working of the forging, exceptwhen Supplementary Requi

30、rement S2 is specified. For upset disk forgings the longitudinal axis of the specimen shall be in eitherthe tangential or radial direction.8.3.1 The location of the longitudinal axis of the tension test specimen shall be located midway between the parallel surfacesof the test extension, if added to

31、the periphery of disks, or midway between the center and surface of solid forgings. For hollowTABLE 1 Chemical RequirementsAElementCarbon Manganese Phosphorus Sulfur Silicon Nickel Chromium MolybdenumColumbium+TantalumNitrogen OtherGrade UNSDesignationF304 S30400 0.08 2.00 0.045 0.030 1.00 8.0-11.0

32、18.0-20.0 . . . .F304H S30409 0.04-0.10 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 . . . .F304L S30403 0.030 2.00 0.045 0.030 1.00 8.0-12.0 18.0-20.0 . . . .F304N S30451 0.08 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 . . 0.10-0.16 .F304LN S30453 0.030 2.00 0.045 0.030 1.00 8.0-11.0 18.0-20.0 . . 0.10-0

33、.16 .F309H S30909 0.04-0.10 2.00 0.045 0.030 1.00 12.0-15.0 22.0-24.0 . . . .F310 S31000 0.15 2.00 0.045 0.030 1.00 19.0-22.0 24.0-26.00 . . . .F310H S31009 0.04-0.10 2.00 0.045 0.030 1.00 19.0-22.0 24.0-26.00 . . . .F316 S31600 0.08 2.00 0.045 0.030 1.00 10.0-14.0 16.0-18.0 2.00-3.00 . . .F316H S31

34、609 0.04-0.10 2.00 0.045 0.030 1.00 10.0-14.0 16.0-18.0 2.00-3.00 . . .F316L S31603 0.035 2.00 0.040 0.030 1.00 10.0-15.0 16.0-18.0 2.00-3.00 . . .F316N S31651 0.08 2.00 0.045 0.030 1.00 10.0-13.0 16.0-18.0 2.00-3.00 . 0.10-0.16 .F316LN S31653 0.030 2.00 0.045 0.030 1.00 10.0-13.0 16.0-18.0 2.00-3.0

35、0 . 0.10-0.16 .F70 S31730 0.030 2.00 0.040 0.010 1.00 15.0-16.5 17.0-19.0 3.0-4.0 . 0.045 Cu 4.0-5.0F321 S32100 0.08 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 . . 0.10 Ti5(C+N)-0.70F321H S32109 0.04-0.10 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 . . . Ti4(C+N)-0.70F347 S34700 0.08 2.00 0.045 0.030 1.0

36、0 9.0-12.0 17.0-19.0 . . . Cb10C-1.10BF347H S34709 0.04-0.10 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 . 8C-1.10 . .F347LN S34751 0.005-0.020 2.00 0.045 0.030 1.00 9.0-13.0 17.0-19.0 . . 0.06-0.10 Cb0.20-0.5015C minF348 S34800 0.08 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 . 10C-1.10 . Co 0.020,Ta 0.1

37、0F348H S34809 0.04-0.10 2.00 0.045 0.030 1.00 9.0-12.0 17.0-19.0 . 8C-1.10 . Co 0.020,Ta 0.10FXM-19 S20910 0.06 4.0-6.0 0.045 0.030 1.00 11.5-13.5 20.5-23.5 1.50-3.00 0.10-0.30 0.20-0.40 V 0.10-0.30FXM-11 S21904 0.04 8.0-10.0 0.045 0.030 1.00 5.5-7.5 19.0-21.5 . . 0.15-0.40 .F46 S30600 0.018 2.00 0.

38、020 0.020 3.7-4.3 14.0-15.5 17.0-18.5 0.20 . . Cu 0.50A Max. unless min or a range is indicated. Where ellipses (.) appear in this table, there is no requirement and the element need not be analyzed for or reported.B Alternatively, tantalum may be substituted for part of the columbium as approved by

39、 the purchaser.A965/A965M 143TABLE 2 Tensile RequirementsAustenitic SteelsGradeF304 F304H F304L F304N F304LN F309H F310 F310H F316 F316H F316L F316N F316LN F321 F321H F347 F347H F347LN F348 F348H FXM-19 FXM-11 F46Tensile strengthmin, ksi MPa70485704856545080550704857048575515704857048570485654508055

40、070485704857048570485704857048570485704851006909062078100540690Yieldstrength(0.2 % offset),min, ksi MPa3020530205251703524030205302053020530205302053020525170352403020530205302053020530205302053020530205553805034532220Elongationin2 in. or50mm, min,%30 30 30 25 30 30 30 30 30 30 30 25 30 30 30 30 30

41、30 30 30 30 40 40Reductionofarea, min,%45 45 45 45 45 45 35 45 45 45 45 45 45 45 45 45 45 45 45 45 50 50 50TABLE 2 Tensile RequirementsAustenitic SteelsGradeF304 F304H F304L F304N F304LN F309H F310 F310H F316 F316H F316L F316N F316LN F70 F321 F321H F347 F347H F347LN F348 F348H FXM-19 FXM-11 F46Tensi

42、lestrength, min,ksi MPa7048570485654508055070485704857551570485704857048565450805507048570480704857048570485704857048570485704851006909062078100540690Yieldstrength(0.2 %offset), min,ksi MPa302053020525170352403020530205302053020530205302052517035240302052517530205302053020530205302053020530205553805

43、034532220Elongationin 2in. or50 mm,min, %30 30 30 25 30 30 30 30 30 30 30 25 30 35 30 30 30 30 30 30 30 30 40 40Reductionof area,min,%45 45 45 45 45 45 35 45 45 45 45 45 45 50 45 45 45 45 45 45 45 50 50 50A965/A965M144forgings, or those heat treated after boring, the specimen shall be located at mid

44、wall. For the special case of forgings that are heattreated solid, but are subsequently bored, the tension test specimen may be taken at the location of the minimum inside diameterafter boring instead of the mid-radius position.9. Grain Size9.1 For Grades F304H, F316H, F309H, F310H, F321H, F347H, an

45、d F348H, the grain size of the forgings shall be ascertainedaccording to Test Methods E112, after solution treatment. One sample shall be examined for each tensile specimen required in 8.2and shall be taken from the tension test location. The grain size shall be number 6, or coarser, over at least 7

46、5 % of the surveyedarea.10. Repair Welding10.1 Repair welding of forgings may be permitted but only at the option of the purchaser. Such repair welds shall be made inaccordance with Section IX of the ASME Boiler and Pressure Vessel Code.11. Marking11.1 The marking requirements of Specification A788/

47、A788M apply.12. Test Reports12.1 The certification requirements of Specification A788/A788M shall apply.13. Keywords13.1 austenitic stainless steel forgings; high temperature service; pressure containing parts; pressure vessel serviceSUPPLEMENTARY REQUIREMENTSOne or more of the following supplementa

48、ry requirements shall apply only when specified by thepurchaser in the inquiry, contract, and order. Details of these supplementary requirements shall beagreed upon between the manufacturer and the purchaser.S1. Rough Turning and BoringS1.1 The position of the rough turning and boring in the sequenc

49、e of manufacturing operations shall be specified.S2. Transverse Tension TestS2.1 Instead of the test specimen orientation requirements in 8.3, the longitudinal axis of the test specimens shall be transverseto the direction of major working of the forging. The results shall conform with requirements of Table 2, with the exception ofthe