ASTM A962 A962M-2017 Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range《低温至蠕变范围任何温度下使用螺栓常规要求的标准规格》.pdf

《ASTM A962 A962M-2017 Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range《低温至蠕变范围任何温度下使用螺栓常规要求的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A962 A962M-2017 Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range《低温至蠕变范围任何温度下使用螺栓常规要求的标准规格》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A962/A962M 16bA962/A962M 17Standard Specification forCommon Requirements for Bolting Intended for Use at AnyTemperature from Cryogenic to the Creep Range1This standard is issued under the fixed designation A962/A962M; the number immediately following the designation indicates the yearof

2、 original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers a group of common requirements

3、that shall apply to carbon, alloy, stainless steel, and nickel alloybolting under any of the following ASTM Specifications (or under any other ASTM Specifications that invoke this specificationor portions thereof):Title of Specifications ASTM DesignationAlloy-Steel and Stainless Steel Bolting Materi

4、alsfor High-Temperature ServiceA193/A193MCarbon and Alloy Steel Nuts for Bolts for HighPressure and High-Temperature ServiceA194/A194MAlloy Steel Bolting Materials for Low-TemperatureServiceA320/A320MAlloy-Steel Turbine-Type Bolting MaterialSpecially Heat Treated for High-TemperatureServiceA437/A437

5、MHigh-Temperature Bolting Materials With ExpansionCoefficients Comparable to Austenitic StainlessSteelsA453/A453MAlloy-Steel Bolting Materials for Special Applications A540/A540MPrecipitation-Hardening Bolting Material (UNSN07718) for High Temperature ServiceA1014/A1014MHigh Strength Precipitation H

6、ardening and DuplexStainless Steel Bolting for Special PurposeApplicationsA1082/A1082M1.2 In case of conflict, the requirements of the individual product specification shall prevail over those of this specification.1.3 Fasteners are a wide-ranging classification that includes screws, bolts, nuts, wa

7、shers, stud bolts, rivets, powder-actuatedstuds, staples, tacks, and pins. Bolting, which is composed of bolting materials, such as rods, bars, flats, and forgings, which aresubsequently manufactured into bolting components, are a special sub-group of fasteners. Bolting materials and components have

8、designated compositions and specific properties intended for applications in aggressive service where commercial generic fastenersmay not be suitable or have insufficient fitness for purpose under certain conditions. These conditions include cryogenic or hightemperature service, or excessive vibrati

9、on, impact, or shock. To further address any other special service conditions where boltingis intended for use, additional requirements may be specified by mutual agreement between the purchaser and supplier.1.4 Supplementary requirements are provided for use at the option of the purchaser. The supp

10、lementary requirements only applywhen specified individually by the purchaser in the purchase order or contract.1.5 This specification is expressed in both inch-pound units and in SI units. Unless the purchase order or contract specifies theapplicable “M” specification designation (SI units) the inc

11、h-pound units shall apply. The values stated in either SI units orinch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values statedin each system may not be exact equivalents; therefore, each system shall be used independently of the o

12、ther. Combining valuesfrom the two systems may result in nonconformance with the specification.1.6 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Stand

13、ards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01.22on Steel Forgings

14、and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications.Current edition approved Dec. 1, 2016May 1, 2017. Published December 2016May 2017. Originally approved in 1997. Last previous edition approved in 2016 asA962/A962M 16a.A962/A962M 16b. DOI:

15、10.1520/A0962_A0962M-16B.10.1520/A0962_A0962M-17.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurat

16、ely, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Dr

17、ive, PO Box C700, West Conshohocken, PA 19428-2959. United States12. Referenced DocumentsThe following documents shall form a part of this specification to the extent specified. The latest issue shall apply unless oth-erwise specified.2.1 ASTM Standards:2A29/A29M Specification for General Requiremen

18、ts for Steel Bars, Carbon and Alloy, Hot-WroughtA193/A193M Specification forAlloy-Steel and Stainless Steel Bolting for HighTemperature or High Pressure Service and OtherSpecial Purpose ApplicationsA194/A194M Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pr

19、essure or HighTemperature Service, or BothA320/A320M Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature ServiceA370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA380/A380M Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, E

20、quipment, and SystemsA437/A437M Specification for Stainless and Alloy-Steel Turbine-Type Bolting Specially Heat Treated for High-TemperatureServiceA453/A453M Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic StainlessSteelsA484/A484M Specification for G

21、eneral Requirements for Stainless Steel Bars, Billets, and ForgingsA540/A540M Specification for Alloy-Steel Bolting for Special ApplicationsA700 Guide for Packaging, Marking, and Loading Methods for Steel Products for ShipmentA751 Test Methods, Practices, and Terminology for Chemical Analysis of Ste

22、el ProductsA788/A788M Specification for Steel Forgings, General RequirementsA941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and FerroalloysA967/A967M Specification for Chemical Passivation Treatments for Stainless Steel PartsA1014/A1014M Specification for Precipitation-Hardening

23、 Bolting (UNS N07718) for High Temperature ServiceA1058 Test Methods for Mechanical Testing of Steel ProductsMetricA1082/A1082M Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special PurposeApplicationsE3 Guide for Preparation of Metallographic Specime

24、nsE381 Method of Macroetch Testing Steel Bars, Billets, Blooms, and ForgingsE384 Test Method for Microindentation Hardness of MaterialsE566 Practice for Electromagnetic (Eddy Current) Sorting of Ferrous MetalsE1417/E1417M Practice for Liquid Penetrant TestingE1444/E1444M Practice for Magnetic Partic

25、le TestingE1916 Guide for Identification of Mixed Lots of MetalsF606/F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners,Washers, Direct Tension Indicators, and RivetsF788/F788M Specification for Surface Discontinuities of Bolts, Screws, and S

26、tuds, Inch and Metric SeriesF812 Specification for Surface Discontinuities of Nuts, Inch and Metric SeriesF1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance InspectionF2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Th

27、readed Steel Bolts,Screws, Studs, and NutsF2328M Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts,Screws, Studs, and Nuts (Metric)2.2 AIAG Standard:3AIAG B-5 02.00 Primary Metals Identification Tag Application Standard2.3 ASME Standards:4B1.

28、1 Screw ThreadsB1.13M Metric Screw Threads M ProfileB1.2 Gages and Gaging for Unified Screw ThreadsB1.3M Screw Thread Gaging Systems for Dimensional Acceptability of Metric Screw ThreadsB18.2.1 Square and Hex Bolts and ScrewsB18.2.2 Metric Heavy Hex NutsB18.2.3.3M Metric Heavy Hex Screws2 For refere

29、ncedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd

30、., Suite 200, Southfield, MI 48033, http:/www.aiag.org.4 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http:/www.asme.org.A962/A962M 172B18.2.3.6M Metric Heavy BoltsB18.2.4.6M Nuts for General ApplicationsB18.

31、2.6 Fasteners Used in Structural ApplicationsB18.2.6M Metric Fasteners for Use in Structural ApplicationsB18.3 Hexagon Socket and Spline Socket ScrewsB18.18 Quality Assurance for FastenersB18.31.2 Continuous Thread Stud, Double-End Stud, and Flange Bolting Stud (Stud Bolt) (Inch Series)2.4 ISO Stand

32、ards:5ISO 4762 Hex Socket Cap Screw2.5 Other Documents:ASNT Recommended Practice No. SNT-TC-1A63. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 annealingmaterial shall be uniformly reheated to a temperature above the transformation range and, after holding fora sufficient time

33、at this temperature, cooled slowly to a temperature below the transformation range.3.1.2 bara solid rolled or forged section that is long in relationship to its cross-sectional dimensions with a relatively constantcross section throughout its length. See Specification A29/A29M for definitions relati

34、ng to the production of hot wrought and coldfinished bars.3.1.3 boltinga general term which includes bolting materials (rolled or forged bars or blanks, wire, rod, threaded bar, rotarypierced or extruded seamless tubes, bored bars, or forged hollows from forged or rolled bar segments), which are man

35、ufacturedinto bolting components, including but not limited to, connectors, pins, restraining device components, shafts, bolts, nuts, screws,studs, and washers.3.1.4 bolting componentscomponents, such as bolts, nuts, screws, studs, washers, connectors, and pins, are finished productswhich join, fast

36、en, restrain, or position objects.3.1.5 bolting materialsstarting materials used for the manufacture of bolting components, such as rolled or forged or threadedsolid bars, blanks, wires, rods, or tubes or other hollow sections, that may be further processed by heat treatment, cold working,forging, t

37、hreading, or machining.3.1.6 certifying organizationthe company or association responsible for the conformance and marking of the product to thespecification requirements.3.1.7 classa term used to differentiate between different heat treatment conditions or strength levels, or both, often within the

38、same grade but sometimes within the same family of materials. May also apply to work hardened condition or strength level, orboth.3.1.8 gradean alloy described individually and identified by its own designation in a table of chemical requirements withinany specification.3.1.9 length, components subj

39、ect to full size testingthat portion of the bolting component whose body diameter isapproximately the same as the nominal thread size.3.1.10 lotunless otherwise specified, a lot shall consist of:3.1.10.1 bolting, heat treated in batch type furnacesall bolting material of the same heat or cast of mat

40、erial, condition, finish,and size subjected to the same heat treatment in one tempering charge and submitted for inspection at the same time.3.1.10.2 bolting, heat treated in continuous type furnacesall bolting material of the same heat or cast of material, condition,finish, and size heat treated wi

41、thout interruption in a continuous type furnace.3.1.10.3 bolting, non heat treated (strain hardened)all bolting material of the same heat or cast of material, condition,reduction (cold work), finish, and size.3.1.10.4 components, machined from bolting materialall bolting components machined from the

42、 same lot of bolting materialdefined as outlined in either 3.1.10.1 or 3.1.10.2, above without any subsequent heat treatment or hot or cold forming.3.1.10.5 components, heat treated in batch type furnacesall bolting component items produced by any manufacturing process(such as rolling, forging, or m

43、achining) from the same heat or cast of material, of the same prior condition, the same size, andsubjected to the same heat treatment in one tempering charge.5 Available from International Organization for Standardization (ISO), ISO Central Secretariat, BIBC II, Chemin de Blandonnet 8, CP 401, 1214

44、Vernier, Geneva,Switzerland, http:/www.iso.org.6 Available from American Society for Nondestructive Testing (ASNT), P.O. Box 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http:/www.asnt.org.A962/A962M 1733.1.10.6 components, heat treated in continuous type furnacesall bolting component items p

45、roduced by any manufacturingprocess (such as rolling, forging, or machining) from the same heat or cast of material, of the same prior condition, of the samesize, and then subjected to the same heat treatment in a four hour period and in one tempering charge.3.1.10.7 components, non heat treated (st

46、rain hardened)all bolting components of the same heat or cast of material, condition,reduction (cold work), finish, and size.3.1.10.8 solution treat or treatment (or solution annealing)material shall be heated to a temperature that causes the carbidesto go into solution and then quenched in water or

47、 rapidly cooled by other means to prevent re-precipitation.3.1.10.9 stress relievingmaterial shall be uniformly heated to the selected stress relieving temperature, held long enough toreduce stresses and then cooled at a rate that will result in the properties required for the material grade and min

48、imize thedevelopment of new residual stresses.3.1.10.10 strain hardened materialaustenitic stainless steel material which has been subjected to cold working sufficient tocause a significant increase in strength.3.2 DefinitionsFor definitions of other terms used in this specification, refer to Termin

49、ology A941.4. Ordering Information4.1 It is the purchasers responsibility to specify in the purchase order all information necessary to purchase the needed material.Examples of such information include, but are not limited, to the following:4.1.1 Quantity and size,4.1.2 Product specification number with grade, class, type, as applicable, and including the product specification year date,4.1.3 Choice of testing track from the options listed in Test Methods A1058 when material is ordered to an M suffix (SI units)product standard. If the choice of tes