ASTM A888-2009 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications《卫生和暴雨排水、污水、和通风管道用无衬套铸铁污水管和配件的标准规范.pdf

《ASTM A888-2009 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications《卫生和暴雨排水、污水、和通风管道用无衬套铸铁污水管和配件的标准规范.pdf》由会员分享，可在线阅读，更多相关《ASTM A888-2009 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain Waste and Vent Piping Applications《卫生和暴雨排水、污水、和通风管道用无衬套铸铁污水管和配件的标准规范.pdf（65页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 888 09Standard Specification forHubless Cast Iron Soil Pipe and Fittings for Sanitary andStorm Drain, Waste, and Vent Piping Applications1This standard is issued under the fixed designation A 888; the number immediately following the designation indicates the year oforiginal adoption

2、or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers hubless cast iron soil pipe andfittings for use in

3、gravity flow applications. It establishesstandards covering material, manufacture, mechanical andchemical properties, dimensions, coating, test methods, inspec-tion, certification, and product marking for hubless cast ironsoil pipe and fittings. These pipe and fittings are intended fornon-pressure a

4、pplications, as the selection of the proper sizefor sanitary drain, waste, vent, and storm drain systems allowsfree air space for gravity drainage.1.2 The EDP/ASA numbers indicated in this section repre-sent a Uniform Industry Code adopted by theAmerican SupplyAssociation (ASA). A group designation

5、prefix, 022, is as-signed to hubless products, followed by the four-digit identi-fication assigned to individual items and a check digit. Thissystem has been instituted to facilitate EDP control throughdistribution channels, and is to be used universally in orderingand specifying product items. Thos

6、e items with no EDPnumbers are either new, special, or transitory and will beassigned numbers on subsequent prints of this specification.1.3 This specification covers pipe and fittings of the follow-ing patterns and applies to any other patterns that conform withthe applicable requirements given in

7、this specification.21.3.1 Lengths:FiguresEDP/ASA Identification Numbersfor Hubless PipeFig. 110 ft (3.0 m) in sizes and 5 ft. (1.5 m)112 ,2,3,4,5,6,8,10, 12, and 15 in.Fig. 1, Fig. 2Method of Specifying Fittings Fig. 31.3.2 Fittings:Quarter Bend Fig. 5Quarter Bend, Reducing Fig. 6Quarter Bend, With

8、Side Opening Fig. 7Quarter Bend, With Heel Opening Fig. 8Quarter Bend, Tapped Fig. 9Quarter Bend, Double Fig. 10Quarter Bend, Long Fig. 11Short Sweep Fig. 12Long Sweep Fig. 13Long Sweep, Reducing Fig. 14Fifth Bend Fig. 15Sixth Bend Fig. 16Eighth Bend Fig. 17Eighth Bend Long Fig. 18Sixteenth Bend Fig

9、. 19Sanitary Tee Fig. 20Sanitary Tee With Side Opening Fig. 21Sanitary Tee With 2 in. Side Opening R or L/R and L Fig. 22Sanitary Tee, New Orleans Special With Side Opening Fig. 23Sanitary Tee With 45 Side Openings and New Orleans Fig. 24Sanitary Special Tee Tapped Fig. 25Sanitary Tapped Tee, Horizo

10、ntal Twin Fig. 26Sanitary Tapped Tee, Double Vertical Fig. 27Y Branch Fig. 28Y Branch, Double Fig. 29Y Branch, Upright Fig. 30Upright Y Wide Center Florida Special Fig. 31Y Branch, Combination18 Bend Fig. 32Y Branch, Combination18 Bend Double Fig. 33Sanitary Cross Fig. 34Sanitary Cross With Side Ope

11、ning Fig. 35Sanitary Cross, New Orleans, With Side Openings Fig. 36Sanitary Cross, New Orleans, With 45 Special andRegular Side OpeningsFig. 37Sanitary Cross, Tapped Fig. 38Test Tee Fig. 39Tapped, Extension Piece Fig. 40Increaser-Reducer Fig. 41Increaser-Reducer, Short Fig. 42Tapped Adapter Fig. 43B

12、lind Plug Fig. 44Iron Body Cleanout-Tapped Fig. 45P Trap Fig. 46P Trap, Long Fig. 47P Trap, Deep Seal Fig. 48P Trap, With Primer Fig. 49P Trap, With Tapped Inlet Fig. 50Hub Adapter Fig. 51Tapped Inlet, Double Fig. 52Modified Combination Wye and18 Bend, Double Fig. 53Modified Combination Wye and18 Be

13、nd, Double, Ex-tendedFig. 54Regular or Extended Left or Right Regular or ExtendedDoubleFig. 55Regular or Extended Left or Right Regular or ExtendedDoubleFig. 56Two-Way Cleanout Fig. 57Twin Cleanout Fig. 58Closet Bend, Regular and Reducing Fig. 59Closet Flange Riser Fig. 601This specification is unde

14、r the jurisdiction of ASTM Committee A04 on IronCastings and is under the direct responsibility of SubcommitteeA04.12 on Pipes andTubes.Current edition approved Jan. 1, 2009. Published January 2009. Originallyapproved in 1990. Last previous edition approved in 2008 as A 888 08a.2Reprinted with permi

15、ssion from Cast Iron Soil Pipe Institute (CISPI), 5959Shallowford Rd., Suite 419, Chattanooga, TN 37421, http:/www.cispi.org. Avail-able from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor,New York, NY 10036, http:/www.ansi.org.1Copyright ASTM International, 100 Barr Harbor

16、Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Tapping Bosses Fig. 61Closet Flanges Fig. 62Double Sweep Sanitary Tee (Extended) Fig. 63Running Trap with Double Vents Fig. 64P Trap with Tapped or Hubless Side Inlet Fig. 65Vented Tub Wye Extended, Double Fig. 66Vented Tub Wye Exte

17、nded Offset, Left or Right Fig. 67Vented Tub Wye Fig. 68Double Two Way Cleanout Fig. 69Sanitary Cross with 3-in. Vent and Two 2-in. 45 Inlets Fig. 70Vented Closet Tee or Cross Fig. 71Double Vertical 90 Stack Fig. 721.4 The values stated in inch-pound units are to be regardedas standard. The values g

18、iven in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The committee with jurisdiction over this standard isaware of another comparable standard published by the CastIron Soil Pipe Institute, CISPI 301.NOTE 1The text of t

19、his standard references notes and footnotes thatprovide explanatory material. These notes and footnotes (excluding thosein tables and figures) shall not be considered as requirements of thestandard.2. Referenced Documents2.1 ASTM Standards:3A 48/A 48M Specification for Gray Iron CastingsA 644 Termin

20、ology Relating to Iron CastingsC 564 Specification for Rubber Gaskets for Cast Iron SoilPipe and FittingsD 1248 Specification for Polyethylene Plastics ExtrusionMaterials for Wire and CableE8 Test Methods for Tension Testing of Metallic MaterialsE 1645 Practice for Preparation of Dried Paint Samples

21、 byHotplate or Microwave Digestion for Subsequent LeadAnalysisE 2349 Practice for Safety Requirements in Metal CastingOperations: Sand Preparation, Molding, and Core Making;Melting and Pouring; and Cleaning and Finishing2.2 Federal Standard:4Fed. Std. No. 123 Marking for Shipment (Civil Agencies)2.3

22、 Military Standard:4MIL-STD-129 Marking for Shipment and Storage2.4 ANSI/ASME Standard:5B1.20 Pipe Threads2.5 Other Documents:Uniform Freight Classification Rules6National Motor Freight Classification Rules7Cast Iron Soil Pipe Institute (CISPI) Specification 30183. Terminology3.1 Abbreviations:3.2 A

23、Cabove centerADAPTRadapterifon the left, it shall be a left-hand fitting.8.2.1 Branch FittingsThe branch shall be placed towardthe observer and the outlet end of the run lower than thebranch.8.3 The fitting illustrated in Fig. 3 has a right-hand inlet.Left-hand fittings have these openings on the si

24、de opposite tothat shown. Inlets on fittings shall be made with or withoutspigot bead and positioning lug.9. Coating9.1 The pipe and fittings shall be furnished coated. The pipeand fittings shall be uniformly coated with a material suitablefor the purpose that is adherent, not brittle, and without a

25、tendency to scale. The coating shall not contain asbestos abovecurrent MSDS reportable levels. Material safety data sheetsshall be furnished by the coating manufacturer when requested.The coating shall be evenly and smoothly applied to allsurfaces, except in threaded openings.9.2 Pipe and fittings s

26、hall not be coated with paint contain-ing lead which exceeds levels above 0.06 % (600 ppm).9.3 The manufacturer shall annually prepare and submitsamples to a qualified laboratory for test in accordance withPractice E 1645.9.4 The manufacturer shall prepare and submit sampleswhen changing sources of

27、supply or the coating manufacturerchanges formulations for the coating.9.5 Records shall be maintained for a period of seven years.9.6 Copies of the coating test shall be furnished whenrequested.10. Sampling10.1 Chemical and mechanical tests shall be made regularlyand at sufficiently close intervals

28、 for adequate determinationsof the significant chemical constituents and properties of thecast iron. A specimen taken from a finished product often doesnot produce the same results as a specimen formed by themethod used for sample preparation and is not acceptable forthe purposes of testing to this

29、standard. Records of chemicalanalysis shall be maintained by the manufacturer. Copies ofthese analyses shall be furnished to the purchaser whenrequested.10.2 A lot shall consist of one of the following:10.2.1 All the metal poured from a single heating is a batchtype furnace.10.2.2 All the metal from

30、 two or more batch type meltingfurnaces poured into a single ladle or a single casting.10.2.3 All the metal poured from a continuous meltingfurnace for a given period of time between changes in charge,processing conditions, or aim-for chemistry or 4 hours, which-ever is the shorter period.11. Test M

31、ethods11.1 Gray Iron:11.1.1 Tensile Strength TestTest bars shall be cast inaccordance with the requirements of Specification A 48/A 48M. The machined test bar dimensions and drawing anddimensions of as cast test bars are found in Fig. 4. The tensilestrength shall be determined in accordance with Tes

32、t MethodsE8.11.1.2 Tension test reports shall include breaking load oftest bars, machined diameter of test bar, and calculated tensilestrength.12. Inspection12.1 Inspection and Test by the ManufacturerPipe andfittings shall be inspected to verify compliance with thisspecification. The manufacturer s

33、hall maintain a record of allinspections.12.2 Pipe InspectionAt regular intervals (not to exceed 12h) during the course of production, sample pieces of each sizeof pipe or pipes being produced shall be selected randomly forinspection. Each pipe selected shall be measured by suitablegages and all dim

34、ensions detailed in Fig. 1 of this specificationverified to comply with the requirements of this specification.The inspection records shall be maintained by the manufacturerfor a period of seven years.12.3 Fitting InspectionAt regular intervals (not to exceedtwelve hours) during the course of produc

35、tion, sample piecesTABLE 1 EDP Identification Numbers for Hubless PipeNOTEWhen ordering by these EDP numbers, be sure to include thecheck (=) digit following the item number (022 0126 7). This check digitis verification of the group and item number you select.ManufacturersItemCodeDescriptionAGroup I

36、tem No. =10 ft (3 m) lengthHubless pipe (see Fig. 1.) 0156 4 1120158 0 2120160 6 3022 0162 2 40164 8 50168 9 60170 5 80171 3 100172 7 120173 1 15AEDP numbers for fittings will appear in each of the respective tables.A888094of each size and configuration of fitting being produced shall beselected ran

37、domly for inspection. Each fitting selected shall bemeasured by suitable gages to verify that the laying length (asdetailed in Figs. 4-72), and all applicable dimensions detailedin Figs. 1 and 2 of this specification comply with the require-ments of this specification. The inspection records shall b

38、emaintained by the manufacturer for a period of seven years.12.4 Marking InspectionInspection shall include verifica-tion that the markings on pipe and fittings comply with Section14 of this specification.13. Certification13.1 Upon request the purchaser, design professional, or theadministrative aut

39、hority having jurisdiction where the productsare being installed shall be furnished certification, by themanufacturer, stating samples representing each lot have beentested and inspected as indicated in this specification and therequirements have been met. If required by the purchaser,design profess

40、ional, or the administrative authority havingjurisdiction where the products are being installed, certificationshall be accompanied by test reports as prepared in accordancewith Sections 11 and 12 of this specification. Tension testreports shall include breaking load machined diameters of testbars a

41、nd calculated tensile strength. Certification shall includelegal name and address of the manufacturer.13.2 Third Party certifiers or inspectors shall utilize theprocedures detailed in Annex A1 when conducting inspectionsat the manufacturing locations.14. Product Marking14.1 Each length of pipe and e

42、ach fitting shall be plainlymarked with the country of origin and the manufacturers nameor manufacturers registered trademark by which the manufac-turer can be readily identified after installation. The markingshall be adequate identification of the manufacturer of the pipeand fittings if it readily

43、 identifies the manufacturer to the enduser of the product.14.1.1 Pipe MarkingsThe pipe shall be marked continu-ously on the barrel with a minimum of 0.75-in. (19-mm)lettering starting within 3 in. of each end of the pipe. Each pipeshall be marked with the date of manufacture. The markingshall be st

44、enciled on the pipe or otherwise applied so as to beclear and legible.14.1.2 On fittings, the marking shall be cast with raisedletters that are not to be located within the “W” dimension, asshown in Fig. 2. Cast markings shall be raised from the wall ofthe fitting unless otherwise noted.15. Packagin

45、g and Package Marking15.1 Government ProcurementUnless otherwise specifiedin the contract, the material shall be packaged in accordancewith the suppliers standard practice, which will be acceptableto the carrier at lowest rates. Containers and packing shallcomply with Uniform Freight Classification

46、Rules or NationalMotor Freight Classification Rules. Marking for shipment ofsuch material shall be in accordance with Fed. Std. No. 123 forcivil agencies and MIL-STD-129 for military agencies.16. Keywords16.1 cast iron; hubless pipe and fittings; no-hub pipe andfittings; soil pipeA888095SizeBarrel S

47、pigotBarrel Thickness, TGasket Po-sitioningLugALayingLength, LBInside DiameterOutsideDiameterOutsideDiameterBead WidthABJMN,60.13 (3.3) Nominal Minimum W10 ft 6 0.50 in.(3.0480 m 613 mm)112 1.50 6 0.09 1.90 6 0.06 1.96 6 0.06 0.25 0.16 0.13 1.13 120(38.1 6 2.29) (48.26 6 1.52) (49.7861.52) (6.35) (3

48、.3) (28.7) (3048)2 1.96 6 0.09 2.356 0.09 2.41 6 0.09 0.25 0.16 0.13 1.13 120(49.8 6 2.29) (59.69 6 2.29) (61.21 6 2.29) (6.35) (3.3) (28.7) (3048)3 2.96 6 0.09 3.356 0.09 3.41 6 0.09 0.25 0.16 0.13 1.13 120(75.2 6 2.29) (85.09 6 2.29) (86.61 6 2.29) (6.35) (3.3) (28.7) (3048)4 3.94 6 0.09 4.38 + 0.

49、09 4.44 6 0.09 0.31 0.19 0.15 1.13 120 0.05(100.08 6 2.29) (111.25 + 2.29) (112.78 6 2.29) (7.87) (3.81) (28.7) (3048)(1.27)5 4.94 6 0.09 5.30 + 0.09 5.36 6 0.09 0.31 0.19 0.15 1.50 120 0.05(125.48 6 2.29) (134.62 + 2.29) (136.14 6 2.29) (7.87) (3.81) (38.1) (3048)(1.27)6 5.94 6 0.09 6.30 + 0.09 6.36 6 0.09 0.31 0.19 0.15 1.50 120 0.05(150.88 6 2.29) (160.02 + 2.29) (161.54 6 2.29) (7.87) (3.81) (38.1) (3048)(1.27)8 7.94 6 0.13 8.38 + 0.09 8.44 6 0.09 0.31 0.23 0.17 2.00 120 0.09(201.68 6 3.3) (212.85 + 3.3) (214.38 6 2.29) (7.87) (4.32) (50.8) (30