ASTM A879 A879M-2006 Standard Specification for Steel Sheet Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface《每面镀层质.pdf

《ASTM A879 A879M-2006 Standard Specification for Steel Sheet Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface《每面镀层质.pdf》由会员分享，可在线阅读，更多相关《ASTM A879 A879M-2006 Standard Specification for Steel Sheet Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface《每面镀层质.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 879/A 879M 06Standard Specification forSteel Sheet, Zinc Coated by the Electrolytic Process forApplications Requiring Designation of the Coating Mass onEach Surface1This standard is issued under the fixed designationA 879/A 879M; the number immediately following the designation indica

2、tes the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers zinc coatings ap

3、plied by theelectrolytic process to hot-rolled and cold-rolled steel sheet.The coating has a smooth, spangle-free surface. The zinc-coated sheet covered in this specification is produced in a widerange of coating masses to provide coatings that are compatiblewith the anticipated service life require

4、d. The coating massvaries, from very thin coatings that are usually painted toprovide good service, to relatively heavy masses that providegood corrosion resistance in the bare (unpainted) condition.1.2 The product shall be coated on one or both surfaces withequal or differential coating masses on t

5、he two surfaces. Sheetcoated with equal coating masses on each surface has similarlevels of corrosion protection on each surface. Often, however,a higher level of corrosion protection is required on one surfacethan is required on the other. Thus one surface is specified tohave a heavier coating mass

6、 than the other. Either surface,when specified to be painted will provide additional corrosionprotection as compared to an unpainted surface.1.3 This coating process has essentially no effect on the basemetal mechanical properties and use is permitted on any gradeof hot- or cold-rolled steel sheet.

7、The coated sheet is availableas Commercial Steel (CS), Drawing Steel (DS), Deep DrawingSteel (DDS), Extra-Deep Drawing Steel (EDDS), StructuralSteel (SS), High-Strength Low-Alloy Steel (HSLAS), High-Strength Low-Alloy Steel with Improved Formability(HSLAS-F), Solution-Hardened Steel (SHS), or Bake-H

8、ardenable Steel (BHS), see Specifications A 1008/A 1008Mand A 1011/A 1011M.1.4 The values stated in either SI or inch-pound units are tobe regarded separately as the standard. Within the text, the SIunits are shown in brackets. The values stated in each systemare not exact equivalents; therefore, ea

9、ch system must be usedindependently of the other.2. Referenced Documents2.1 ASTM Standards:2A 90/A 90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA 754/A 754M Test Method for Coating Weight (Mass) ofMetallic Coatings on Steel by X-Ray Fluorescenc

10、eA 917 Specification for Steel Sheet, Coated by the Electro-lytic Process forApplications Requiring Designation of theCoating Mass on Each Surface (General Requirements)A 1008/A 1008M Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy,High-Strength Low-Alloy wit

11、h Improved Formability, So-lution Hardened, and Bake HardenableA 1011/A 1011M Specification for Steel, Sheet and Strip,Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy,High-Strength Low-Alloy with Improved Formability, andUltra-High StrengthB 504 Test Method for Measurement of Thickness of Me

12、-tallic Coatings by the Coulometric Method3. Classification3.1 Coating shall be designated in accordance with Speci-fication A 917. The letter G shall be used to designate SI unitsof pure zinc coatings. The letter Z shall be used to designateinch-pound units of pure zinc coating.4. Ordering Informat

13、ion4.1 Orders for products to this specification shall include thefollowing information, as necessary to adequately describe thedesired product:4.1.1 Name of product (electrolytic zinc-coated steel sheet).4.1.2 ASTM designation and year of issue.4.1.3 Base metal type (hot rolled or cold rolled).4.1.

14、4 Base metal designation (Commercial Steel (CS),Drawing Steel (DS), Deep Drawing Steel (DDS), Extra Deep1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.11 on Sheet Specifications.Current

15、 edition approved Nov. 1, 2006. Published December 2006. Originallyapproved in 1987. Last previous edition approved in 2004 as A 879/A 879M - 04.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards

16、volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Drawing Steel (EDDS), Structural St

17、eel (SS), High-StrengthLow-Alloy Steel (HSLAS), High-Strength Low-Alloy Steelwith Improved Formability (HSLAS-F), Solution-HardenedSteel (SHS), or Bake-Hardenable Steel (BHS).4.1.5 Formability type, strength, grade or class, or combi-nation, thereof, as required for structural or high-strengthlow-al

18、loy steels.4.1.6 Coating designation (see 3.1).4.1.7 Surface treatments required (see Note 1).NOTE 1Steel sheet is available without surface treatment (dry) or withsurface treatments designated as chemical treatment, oiled, or phos-phatized. Unless otherwise specified sheet is furnished oiled.4.1.8

19、Dimensions show thickness (minimum or nominal),width, and length, if cut length.4.1.9 Coil size requirements (specify maximum outsidediameter (OD), acceptable inside diameter (ID), and maximumweight (mass).4.1.10 Application (part name and description).4.1.11 Special Requirements, is applicable.4.1.

20、12 Certification, if required, heat analysis and mechani-cal property report.5. Coating Mass5.1 Coating mass shall conform to the requirements forcoating designation (mass and type) as given in SpecificationA 917 and in Table 1 for the specific coating designation. Themass of the coating is the sing

21、le spot value on each surface ofthe sheet in grams per square metre for G coatings and ouncesper square foot for Z coatings.5.2 Coating Mass Tests:5.2.1 The weigh-strip-weigh method (see Test MethodA 90/A 90M) is a destructive test that determines coating massby measuring the difference in weight be

22、tween a coated and astripped (uncoated) sample. If one surface is protected suitablyduring the initial stripping, coating mass can be determined foreach surface independently. Conversion of the coating mass tocoating thickness is possible only if the density of the coatingis known precisely.5.2.2 Co

23、ating thickness measurements by X-ray fluores-cence (see Test Method A 754) is a nondestructive test thatdetermines coating mass by converting X-ray fluorescencemeasurements to coating mass values. This method is readilyadaptable to the continuous monitoring of coating mass duringcoating. Thus moder

24、n electroplating facilities are frequentlyequipped with X-ray fluorescence gages that provide feedbackto control the coating mass. These devices may be used as abasis for determining suitability for shipment provided thatthey have been calibrated properly.5.2.3 Measurement by Coulometric Method (see

25、 TestMethod B 504) is a destructive test that determines lightercoating mass applications.5.3 The referee method to be used shall be as agreed uponbetween the producer and the consumer. In the absence of suchagreement, Test Method A 90/A 90M shall be used as thereferee method.5.3.1 Estimate the coat

26、ing thickness from the coatingweight (mass) by using the following relationships:5.3.1.1 Inch-Pound Units1 oz/ft2coating weight = 1.7mils coating thickness (0.0017 in.); 1 mil (0.001 in.) coatingthickness = 0.59 oz/ft2coating weight.5.3.1.2 SI Units1 g/m2coating mass = 0.14 micro-metrecoating thickn

27、ess; 1 micro-metre coating thickness = 7.14 g/m2coating mass.6. Keywords6.1 electrolytic zinc coated; steel sheet, zinc coated; zinccoated; zinc coated steel sheetTABLE 1 Coating Weight and Mass per Surface,Afor Steel Sheet, Zinc Coated by the Electrolytic ProcessBInch-Pound Units, oz/ft2SI Units, g

28、/m2Coating DesignationCMinimum Maximum Coating DesignationCMinimum Maximum00Z no coating no coating 00G no coating no coating01ZD0.01 0.05 03GD31502ZE0.02 0.08 06GE6204ZF0.04 0.10 12GF12 3007Z 0.07 0.13 20G 20 4008ZG0.08 0.16 24GG24 4513Z 0.13 0.23 40G 40 7020Z 0.20 0.30 60G 60 9023Z 0.23 0.36 70G 7

29、0 11030Z 0.30 0.43 90G 90 13032Z 0.32 0.46 98G 98 140AConversion for coating weight and mass are: 1 oz/ft2= 305.15 g/m2and1g/m2= 0.00328 oz/ft2.BThe product shall be coated on at least one surface; therefore, the combination 00Z/00Z or 00G/00G shall not be specified.CSee Specification A 917.DFormall

30、y Flash CoatingEFormally Intermediate CoatingFFormally Full CoatingGFormally Double CoatingA 879/A 879M 062SUMMARY OF CHANGESCommittee A05 has identified the location of selected changes to this standard since the last issue(A 879/A 879M - 04) that may impact the use of this standard. (November 1, 2

31、006)(1) Revised 1.3, 2.1, and 4.1.4 to include Solution-HardenedSteel (SHS) and Bake-Hardenable Steel (BHS) designations.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expres

32、sly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,

33、 either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may at

34、tend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).A 879/A 879M 063