ASTM A705 A705M-2017 Standard Specification for Age-Hardening Stainless Steel Forgings《时效硬化不锈钢锻件的标准规格》.pdf

《ASTM A705 A705M-2017 Standard Specification for Age-Hardening Stainless Steel Forgings《时效硬化不锈钢锻件的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A705 A705M-2017 Standard Specification for Age-Hardening Stainless Steel Forgings《时效硬化不锈钢锻件的标准规格》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A705/A705M 13A705/A705M 17Standard Specification forAge-Hardening Stainless Steel Forgings1This standard is issued under the fixed designation A705/A705M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of las

2、t revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification2 covers age-hardening stainless steel forgings for general use.1.2 The values stated in either

3、SI units or inch-pound units are to be regarded separately as standard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.3 Unless the o

4、rder specifies an “M” designation, the material shall be furnished to inch-pound units.NOTE 1Bar products are covered by Specification A564/A564M.1.4 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Pr

5、inciples for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3A370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA484/A484M Specif

6、ication for General Requirements for Stainless Steel Bars, Billets, and ForgingsA564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and ShapesA751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel ProductsE527 Practice for Numbering Meta

7、ls and Alloys in the Unified Numbering System (UNS)2.2 Other Documents:4SAE J 1086 Recommended Practice for Numbering Metals and Alloys (UNS)3. Ordering Information3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under thisspecificatio

8、n. Such requirements may include but are not limited to the following:3.1.1 Quantity (weight or number of pieces),3.1.2 Name of material (age-hardening stainless steel forgings),3.1.3 Dimensions, including prints or sketches,3.1.4 Type or UNS designation (Table 1),3.1.5 Heat-treated condition (Secti

9、on 5),3.1.6 Transverse properties when required (7.4),3.1.7 ASTM designation and date of issue, and3.1.8 Special requirements (5.3, 5.4).3.2 If possible, the intended end use of the item should be given on the purchase order, especially when the item is ordered fora specific end use or uses.NOTE 2At

10、ypical ordering description is as follows: 5 age-hardening stainless steel forgings, Type 630, solution-annealed,ASTM Specification A7051 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01

11、.17on Flat-Rolled and Wrought Stainless Steel.Current edition approved May 1, 2013Nov. 15, 2017. Published July 2013November 2017. Originally approved in 1974. Last previous edition approved in 20092013 asA705/A705M 95 (2009).A705/A705M 13. DOI: 10.1520/A0705_A0705M-13.10.1520/A0705_A0705M-17.2 For

12、ASME Boiler and Pressure Vessel Code applications see related Specification SA-705/SA-705M in Section II of that Code.3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to

13、 the standards Document Summary page on the ASTM website.4 Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been

14、made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*

15、A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1dated _ . End use: pump blocks for oil well equipment.4. General Requirements4.1 In addition to the requirements of this s

16、pecification, all requirements of the current edition of Specification A484/A484Mshall apply. Failure to comply with the general requirements of Specification A484/A484M, constitutes nonconformance with thisspecification.5. Materials and Manufacture5.1 Material for forgings shall consist of billets

17、or bars, either forged, rolled or cast, or a section cut from an ingot. The cutsshall be made to the required length by a suitable process. This material may be specified to Specification A564/A564M.5.2 The material shall be forged by hammering, pressing, rolling, extruding, or upsetting to produce

18、a wrought structurethroughout and shall be brought as nearly as possible to the finished shape and size by hot working.5.3 When specified on the order, sample forging may be sectioned and etched to show flow lines and the condition in regardto internal imperfections. When so specified, the question

19、of acceptable and unacceptable metal flow shall be subject to agreementbetween the manufacturer and the purchaser prior to order entry.5.4 When specified on the order, the manufacturer shall submit for approval of the purchaser a sketch showing the shape of therough forging before machining, or befo

20、re heat treating for mechanical properties.5.5 The grain size shall be as fine as practicable and precautions shall be taken to minimize grain growth.5.6 Material of types other than XM-9 shall be furnished in the solution-annealed condition, or in the equalized andover-tempered condition, as noted

21、in Table 2, unless otherwise specified by the purchaser.5.6.1 Types 630, XM-16, and XM-25 may be furnished in the solution-annealed or age-hardened condition.6. Chemical Composition6.1 The steel shall conform to the chemical composition limits specified in Table 1.6.2 Methods and practices relating

22、to chemical analysis required by this specification shall be in accordance with Test Methods,Practices, and Terminology A751.7. Mechanical Properties7.1 The material, as represented by mechanical test specimens, shall conform to the mechanical property requirements specifiedin Table 2 and shall be c

23、apable of developing the properties in Table 3 when heat treated as specified in Table 3.7.2 The yield strength shall be determined by the offset method as described in the current edition of Test Methods andDefinitions A370. The limiting permanent offset shall be 0.2 % of the gage length of the spe

24、cimen.7.3 The impact strength shall be determined at 70 to 80F 20 to 25C, by Charpy V-notch specimen Type A as described inTest Methods and Definitions A370.TABLE 1 Chemical RequirementsAComposition, %UNSDesignationBType Carbon Manganese Phospho-rusSul-furSili-conChromium Nickel Alumi-numMolyb-denum

25、Tita-niumCopper OtherElementsS17400 630 0.07 1.00 0.040 0.030 1.00 15.0017.50 3.005.00 . . . 3.005.00 CS17700 631 0.09 1.00 0.040 0.030 1.00 16.0018.00 6.507.75 0.751.50 . . . .S15700 632 0.09 1.00 0.040 0.030 1.00 14.0016.00 6.507.75 0.751.50 2.003.00 . . .S35500 634 0.100.15 0.501.25 0.040 0.030 0

26、.50 15.0016.00 4.005.00 . 2.503.25 . . DS17600 635 0.08 1.00 0.040 0.030 1.00 16.0017.50 6.007.50 0.40 . 0.401.20 . .S15500 XM-12 0.07 1.00 0.040 0.030 1.00 14.0015.50 3.505.50 . . . 2.504.50 CS13800 XM-13 0.05 0.20 0.010 0.008 0.10 12.2513.25 7.508.50 0.901.35 2.002.50 . . ES45500 XM-16 0.03 0.50 0

27、.015 0.015 0.50 11.0012.50 7.509.50 . 0.50 0.901.40 1.502.50 FS45503 . 0.010 0.50 0.010 0.010 0.20 11.0012.50 7.509.50 . 0.50 1.001.35 1.502.50 FS45000 XM-25 0.05 1.00 0.030 0.030 1.00 14.0016.00 5.007.00 . 0.501.00 . 1.251.75 GS10120 0.02 0.25 0.015 0.010 0.25 11.0012.50 9.0010.50 0.801.10 1.752.25

28、 0.200.50 . ES11100 0.02 0.25 0.015 0.010 0.25 11.0012.50 10.2511.25 1.351.75 1.752.25 0.200.50 . EA Limits are in percent maximum unless shown as a range or stated otherwise.B New designation established in accordance with Practice E527 and SAEJ1086, Recommended Practice for Numbering Metals and al

29、loys (UNS).C Columbium plus tantalum 0.150.45.D Nitrogen 0.070.13.E Nitrogen 0.01.F Columbium plus tantalum 0.100.50.G Columbium 8 times carbon minimum.A705/A705M 1727.4 Material tensile tested and, when specified, impact tested in the transverse direction (perpendicular to the forging flow lines)an

30、d meeting the requirements shown in Table 3Table 3 need not be tested in the longitudinal direction.7.5 Samples cut from forging shall conform to the mechanical properties of Table 3 when heat treated as specified in Tables 2and 3 and tested in accordance with Test Methods and Definitions A370.8. Pr

31、olongations for Tests8.1 Subject to Section 7, the forgings shall be produced with prolongations for testing, unless otherwise specified. The producermay elect to submit an extra forging to represent each test lot instead of prolongations, or the test specimens can be taken fromthe forgings themselv

32、es.9. Number of Tests9.1 For all classes of forgings weighing from 5000 to 7000 lb 2300 to 3200 kg each, at least one tension test shall be madefrom each forging.TABLE 2 Solution Heat TreatmentType Condi-tion Solution TreatmentMechanical Test Requirements in Solution Treated ConditionATensile Streng

33、th, min Yield Strength, min Elongationin 2 in. 50mm or 4D,min. %Reductionof Area,minute %HardnessBksi MPa ksi MPa Rockwell C,maxBrinell,max630 A 1900 25F 1040 15C(cool as required to below 90F 32C). . . . . . . . . . . . . . . . . . 38 363631 A 1900 25F 1040 15C (water quench) . . . . . . . . . . .

34、. . . . . . . Rb89 229632 A 1900 25F 1040 15C (water quench) . . . . . . . . . . . . . . . . . . Rb100 269C634D A 1900 25F 1040 15C quench, holdnot less than 3 h at minus 100F or lower. . . . . . . . . . . . . . . . . . . . . 363D635 A 1900 25F 1040 15C (air cool) 120 825 75 515 10 45 32 302XM-12 A

35、1900 25F 1040 15C(cool as required to below 90F 32C). . . . . . . . . . . . . . . . . . 38 363XM-13 A 1700 25F 925 15C(cool as required to below 60F 16C). . . . . . . . . . . . . . . . . . 38 363XM-16 A 1525 25F 830 15C (cool rapidly) . . . . . . . . . . . . . . . . . . 36 331S45503 A 1525 25F 830 1

36、5C (cool rapidly) . . . . . . . . . . . . . . . . . . 36 331XM-25 A 1900 25F 1040 15C (cool rapidly) 125E 860 95 655 10 40 33 311S10120 A 1545 25F 840 14C(cool rapidly below 90F 32C). . . . . . . . . . . . . . . . . . 36 331S11100 A 1545 25F 840 14C(oil or water quench), hold for min. 8 h atminus 10

37、0F -73C,F air warm. . . . . . . . . . . . . . . . . . 36 331TABLE 2 Solution Heat TreatmentType Condition Solution TreatmentMechanical Test Requirements in Solution Treated ConditionATensile Strength, min Yield Strength, min Elongationin 2 in.50 mm or4D, min. %Reductionof Area,minute %HardnessBksi M

38、Pa ksi MPa Rockwell C,max Brinell,max630 A 1900 25F 1040 15C(cool as required to below 90F 32C). . . . . . . . . . . . . . . . . . 38 363631 A 1900 25F 1040 15C (water quench) . . . . . . . . . . . . . . . . . . Rb89 229632 A 1900 25F 1040 15C (water quench) . . . . . . . . . . . . . . . . . . Rb100

39、 269C634D A 1900 25F 1040 15C quench, holdnot less than 3 h at minus 100F or lower. . . . . . . . . . . . . . . . . . . . . 363D635 A 1900 25F 1040 15C (air cool) 120 825 75 515 10 45 32 302XM-12 A 1900 25F 1040 15C(cool as required to below 90F 32C). . . . . . . . . . . . . . . . . . 38 363XM-13 A

40、1700 25F 925 15C(cool as required to below 60F 16C). . . . . . . . . . . . . . . . . . 38 363XM-16 A 1525 25F 830 15C (cool rapidly) . . . . . . . . . . . . . . . . . . 36 331S45503 A 1525 25F 830 15C (cool rapidly) . . . . . . . . . . . . . . . . . . 36 331XM-25 A 1900 25F 1040 15C (cool rapidly) 1

41、25E 860 95 655 10 40 33 311S10120 A 1545 25F 840 14C(cool rapidly below 90F 32C). . . . . . . . . . . . . . . . . . 36 331S11100 A 1545 25F 840 14C(oil or water quench), hold for min. 8 h atminus 100F -73C,F air warm. . . . . . . . . . . . . . . . . . 36 331A See 6.1.B Either Rockwell C hardness or

42、Brinell is permissible. On sizes of 12 in. (12.70 mm) and smaller, Rockwell C is preferred.C 321 BHN for rounds cold drawn after solution treating.D Equalization and over-tempering treatment 1425 50F 775 30C for not less than 3 h, cool to room temperature, heat to 1075 25F 580 15C for not less than3

43、 h.E 125 165 ksi 860 1140 MPa for sizes up to 12 in. 13 mm.F Required hold time at minus 100F -73C is not mandatory if product is under 2 in. 51 mm thickness.A705/A705M 173TABLE 3 Mechanical Test Requirements After Age Hardening Heat TreatmentAType Condi-tionSuggested Hardening or Aging Treatment,or

44、 bothBCD ApplicableThickness, in.and TestDirectionETensileStrength,minYieldStrength,minFElon-gationin 2 in.50mm or4D,min. %Reduc-tion ofarea,min,%HardnessGImpactCharpy-V,minTem-perature,F CTime,h Quench ksi MPa ksi MPaRock-wellC,minBrinell,min ftlbf J630 H900 900 480 1.0 air cool Up to 3 in. incl75

45、mm (L)190 1310 170 1170 10 40 40 388 . . . . . .Over 3 in. 75 mmto 8 in. incl200 mm (L)35H925 925 495 4.0 air cool Up to 3 min. incl75 mm (L)170 1170 155 1070 10 44 38 375 5 6.8Over 3 in. 75 mmto 8 in. incl200 mm (L)38H1025 1025 550 4.0 air cool 155 1070 145 1000 12 45 35 331 15 20H1075 1075 580 4.0

46、 air cool 145 1000 125 860 13 45 32 311 20 27H1100 1100 595 4.0 air cool Up to 8 in. incl200 mm (L)140 965 115 795 14 45 31 302 25 34H1150 1150 620 4.0 air cool 135 930 105 725 16 50 28 277 30 41H1150D 1150 620 for 4 h, air cool plus1150 620 for 4 h, air cool125 860 105 725 16 50 2433 max255311 max3

47、0 41H1150M 1400 760 for 2 h, air cool plus1150 620 for 4 h, air cool.115 795 75 520 18 55 24 255 55 75631 RH950 1750F 955C for not less than 10 min,but not more than 1 h, cool rapidly to roomtemperature. Cool within 24 h to minus 100 10F 75C, hold not less than 8 h.Warm in air to room temperature. H

48、eat to950F 510C, hold 1 h, air cool.Up to 4 in. incl.100 mm (L)185 1280 150 1030 6 10 41 388 . . . . . .TH1050 Alternative treatment: 1400F 760C hold90 min, cool to 55 5F 15 3C within 1h. Hold not less than 30 min, heat to1050F 565C hold for 90 min, air cool.Up to 6 in. incl150 mm (L) 170 1170 140 965 6 25 38 352 . . . . . .632 RH950 Up to 4 in. incl100 mm (L) 2001380 175 1210 7 25 . . . 415 . . . . . .