ASTM A601-2005(2010) Standard Specification for Electrolytic Manganese Metal《电解锰金属的标准规范》.pdf
《ASTM A601-2005(2010) Standard Specification for Electrolytic Manganese Metal《电解锰金属的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM A601-2005(2010) Standard Specification for Electrolytic Manganese Metal《电解锰金属的标准规范》.pdf(2页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A601 05 (Reapproved 2010)Standard Specification forElectrolytic Manganese Metal1This standard is issued under the fixed designation A601; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num
2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers several grades of electrolyticmanganese designated as follows:GradeRegular AIntermediate Hydrogen BLow Hydrogen
3、C4.5 % Nitrogen Bearing D6 % Nitrogen Bearing EWeld Grade Powder F2. Referenced Documents2.1 ASTM Standards:2A1025 Specification for Ferroalloys and Other AlloyingMaterials, General RequirementsE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3. General Conditions for Delivery3.1 Mate
4、rials furnished to this specification shall conform tothe requirements of SpecificationA1025, including any supple-mentary requirements that are indicated in the purchase order.Failure to comply with the general requirements of Specifica-tion A1025 constitutes nonconformance with this specification.
5、In case of conflict between the requirements of this specifica-tion and Specification A1025, this specification shall prevail.4. Chemical Requirements4.1 The various grades shall conform to the requirements asto chemical composition specified in Table 1 and Table 2.4.2 The manufacturer shall furnish
6、 an analysis of eachshipment showing the percentage of each element specified inthe applicable table.5. Size5.1 The various grades are available in the sizes listed inTable 3.5.2 The sizes listed in Table 3 are typical as shipped fromthe manufacturers plant. These alloys exhibit varying degreesof fr
7、iability; therefore, some attrition may be expected intransit, storage, and handling (see 5.3 and SpecificationA1025).5.3 Friability Ratings:Grades A, B, CGrades D, ENo. 6No. 56. Chemical Analysis6.1 Chemical analysis methods are subject to agreementbetween the purchaser and the supplier.7. Packagin
8、g7.1 Color coding shall be used when shipment is made incontainers. The color coding may be used in lieu of gradedesignation, if agreed upon between the purchaser and themanufacturer. The following colors shall be used to designatethe grades:Color Designation GradeBlue Regular APurple Intermediate H
9、ydrogen BWhite Low Hydrogen CRed 4.5 % Nitrogen Bearing DYellow 6 % Nitrogen Bearing ENo color Weld Grade Powder F8. Keywords8.1 electrolytic manganese; electrolytic manganese powder;intermediate hydrogen electrolytic manganese; low hydrogenelectrolytic manganese; manganese metal; nitrogen bearingma
10、nganese; weld grade electrolytic manganese powder; weldgrade powdered electrolytic manganese1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition approved Apri
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA60120052010STANDARDSPECIFICATIONFORELECTROLYTICMANGANESEMETAL 电解锰 金属 标准规范 PDF

链接地址:http://www.mydoc123.com/p-458918.html