ASTM A553 A553M-2010 Standard Specification for Pressure Vessel Plates Alloy Steel Quenched and Tempered 8 and 9 Percent Nickel《压力容器用经回火和淬火的含8%及9%镍合金钢板的标准规格》.pdf

《ASTM A553 A553M-2010 Standard Specification for Pressure Vessel Plates Alloy Steel Quenched and Tempered 8 and 9 Percent Nickel《压力容器用经回火和淬火的含8%及9%镍合金钢板的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A553 A553M-2010 Standard Specification for Pressure Vessel Plates Alloy Steel Quenched and Tempered 8 and 9 Percent Nickel《压力容器用经回火和淬火的含8%及9%镍合金钢板的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A553/A553M 10Standard Specification forPressure Vessel Plates, Alloy Steel, Quenched andTempered 8 and 9 % Nickel1This standard is issued under the fixed designation A553/A553M; the number immediately following the designation indicates the yearof original adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers 8 and 9 % nickel alloy steelplates for use in the water quenched and te

3、mpered conditionintended for the fabrication of welded pressure vessels.1.2 Material under this specification is available in twotypes having different chemical composition as follows:Type Nominal Nickel Content, %I9II 81.3 Plates produced under this specification are subject toimpact testing at 320

4、F 195C for Type I, and 275F170C for Type II or at such other temperatures as areagreed upon.1.4 The maximum thickness of plates is limited only by thecapacity of the material to meet the specified mechanicalproperty requirements; however, current mill practice normallylimits this material to 2 in. 5

5、0 mm max.1.5 This material is susceptible to magnetization. Use ofmagnets in handling after heat treatment should be avoided ifresidual magnetism would be detrimental to subsequent fabri-cation or service.1.6 The values stated in either inch-pound units or SI unitsare to be regarded separately as st

6、andard. Within the text, theSI units are shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation.1.7 This standard does not p

7、urport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3

8、A20/A20M Specification for General Requirements forSteel Plates for Pressure VesselsA435/A435M Specification for Straight-Beam UltrasonicExamination of Steel PlatesA577/A577M Specification for Ultrasonic Angle-Beam Ex-amination of Steel PlatesA578/A578M Specification for Straight-Beam UltrasonicExam

9、ination of Rolled Steel Plates for Special Applica-tions3. General Requirements and Ordering Information3.1 Material supplied to this material specification shallconform to Specification A20/A20M. These requirements out-line the testing and retesting methods and procedures, permit-ted variations in

10、dimensions, and mass, quality and repair ofdefects, marking, loading, and ordering information.3.2 In addition to the basic requirements of this specifica-tion, certain supplementary requirements are available whenadditional control, testing, or examination is required to meetend use requirements. T

11、he purchaser is referred to the listedsupplementary requirements in this specification and to thedetailed requirements in Specification A20/A20M.3.3 If the requirements of this specification are in conflictwith the requirements of SpecificationA20/A20M, the require-ments of this specification shall

12、prevail.4. Manufacture4.1 Steelmaking PracticeThe steel shall be killed andshall conform to the fine austenitic grain size requirement ofSpecification A20/A20M.5. Heat Treatment5.1 All plates shall be heat treated in accordance with 5.2.Shell plates and other parts, including heads and reinforcingpa

13、ds, which are heated for forming, shall be heat treated afterforming in accordance with 5.2.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and Pressure

14、Vessels.Current edition approved Oct. 1, 2010. Published November 2010. Originallyapproved in 1965. Last previous edition approved in 2006 as A553/A553M 06.DOI: 10.1520/A0553_A0553M-10.2For ASME Boiler and Pressure Vessel Code applications, see related Specifi-cation SA-553/SA-553M in Section II of

15、that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end o

16、f this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 Heat Treatment ProcedureHeat treat all plates byheating to a suitable temperature within the range from 1475 to1700F 800 to 925C, holding for a sufficient time to obt

17、ainuniform temperature throughout the plate thickness and thenquenching in water. Subsequently, temper the plates within therange from 1050 to 1175F 565 to 635C, holding at thistemperature for a minimum of 30 min/in. 1.2 min/mm ofthickness but not less than 15 min, and cool in air or waterquench at

18、a rate not less than 300F/h 165C/h.5.2.1 Hardening The plates shall be heated to a tempera-ture within the range from 1475 to 1700F 800 to 925C, heldat that temperature for a sufficient time to obtain uniformtemperature throughout the plate thickness, and then quenchedin a liquid media.5.2.2 Temperi

19、ng The plates shall be tempered at a tem-perature within the range from 1050 to 1175F 565 to 635C,being held at that temperature for a minimum of 30 min/in. 1.2min/mm of thickness, but in no case less than 15 min, and thencooled in air or liquid-quenched at a rate not less than 300F/h165C/h.5.2.2.1

20、Prior to the tempering treatment, the plates may besubjected to an intermediate heat treatment consisting ofheating to a temperature in the range from 1165 to 1290F 630to 700C for Type I, or 1185 to 1310F 640 to 710C forType II, holding at that temperature for a minimum of 1 h/in.2.4 min/mm of thick

21、ness, but in no case less than 15 min, andthen water-quenching to below 300F 150C in the case ofplate thicknesses of more than58 in. 16 mm or cooling in airor water-quenching to below 300F 150C in the case of platethicknesses of58 in. 16 mm and under.NOTE 1The intermediate heat treatment is for the

22、purpose of enhanc-ing elongation and notch-toughness and for reducing susceptibility tostrain-aging embrittlement and temper embrittlement. It may be per-formed at the option of the material manufacturer or may be specified bythe purchaser.6. Chemical Requirements6.1 The steel shall conform to the c

23、hemical requirementsshown in Table 1 unless otherwise modified in accordance withSupplementary Requirement S17, Vacuum Carbon-DeoxidizedSteel, in Specification A20/A20M.7. Mechanical Requirements7.1 Tension Test RequirementsThe material as representedby tension-test specimens shall conform to the re

24、quirementsspecified in Table 2.7.1.1 Upon agreement between the purchaser and the manu-facturer, yield strength may be determined by the extensionunder load method, using 0.005 in./in. mm/mm total exten-sion.7.1.2 For nominal plate thicknesses of34 in. 20 mm andunder, the 112 in. 40 mm wide rectangu

25、lar specimen may beused for the tension test and the elongation may be determinedin a 2 in. 50 mm gage length that includes the fracture andshows the greatest elongation.7.2 Impact Test Requirements:7.2.1 Charpy V-notch impact tests shall be made in accor-dance with Specification A20/A20M.7.2.2 The

26、longitudinal axis of the test specimens shall betransverse to the final rolling direction of the plate.7.2.3 Unless otherwise agreed, tests shall be conducted at320F 195C for Type I and at 275F 170C for TypeII.7.2.4 Each test specimen shall have a lateral expansionopposite the notch of not less than

27、 0.015 in. 0.381 mm.8. Finish8.1 Because retained scale may mask surface imperfections,as well as mar the plate surface, plates shall be descaled by theproducer after heat treatment. In the case of material to beheat-treated by the purchaser, the plates shall be descaled bythe producer prior to ship

28、ment.9. Marking9.1 In addition to the marking required in SpecificationA20/A20M, each plate shall be legibly stamped or stenciled,depending upon the ordered thickness, with the letters QT,except as otherwise specified in 9.1.1.9.1.1 When the optional heat treatment in 5.2.2.1 is per-formed, the plat

29、es shall be marked with the letters QTT insteadof QT.10. Keywords10.1 alloy steel; alloy steel plate; pressure containing parts;pressure vessel steels; steel plates; steel plates for pressurevessel applicationsTABLE 1 Chemical RequirementsElement Composition, %Type I Type IICarbon, maxA0.13 0.13Mang

30、anese, max:Heat analysis 0.90 0.90Product analysis 0.98 0.98Phosphorus, maxA0.015 0.015Sulfur, maxA0.015 0.015Silicon:Heat analysisB0.150.40 0.150.40Product analysisC0.130.45 0.130.45Nickel:Heat analysis 8.509.50 7.508.50Product analysis 8.409.60 7.408.60AApplies to both heat and product analyses.BS

31、ilicon may be less than 0.15 %, provided total aluminum is 0.030 % or over,or provided acid soluble aluminum is 0.025 % or over.CSilicon may be less than 0.13 %, provided total aluminum is 0.030 % or over,or provided acid soluble aluminum is 0.025 % or over.TABLE 2 Tensile RequirementsTensile streng

32、th, ksi MPa 100 to 120 690825Yield strength (0.2 % offset), min, ksi MPa 85 585Elongation in 2 in. 50 mm, min, %A20.0ASee Specification A20/A20M for elongation adjustment.A553/A553M 102SUPPLEMENTARY REQUIREMENTSSupplementary requirements shall not apply unless specified in the order.A list of standa

33、rd supplementary requirements for use at the option of the purchaser are includedin Specification A20/A20M. Several of those considered suitable for use with this specification arelisted below by title. Other tests may be performed by agreement between the supplier and thepurchaser.S1. Vacuum Treatm

34、ent,S2. Product Analysis,S3. Simulated Post-Weld Heat Treatment of MechanicalTest Coupons,S6. Drop Weight Test (for Material 0.625 in. 16 mm andover in Thickness),S8. Ultrasonic Examination in accordance with Specifica-tion A435/A435M,S9. Magnetic Particle Examination,S11. Ultrasonic Examination in

35、accordance with Specifica-tion A577/A577M,S12. Ultrasonic Examination in accordance with Specifica-tion A578/A578M, andS17. Vacuum Carbon-Deoxidized Steel.ADDITIONAL SUPPLEMENTARY REQUIREMENTSAlso listed below are additional optional Supplementary Requirements S55 and S56, which aresuitable for this

36、 specification.S55. Longitudinal Charpy Impact Energy AbsorptionRequirementS55.1 The longitudinal Charpy V-notch impact propertiesshall not be less than 25 ftlbf 34 J at the specified tempera-ture.S55.2 Each impact test value shall constitute the averagevalue of three specimens, with not more than o

37、ne value belowthe specified minimum value of 25 ftlbf 34 J but in no casebelow 20 ftlbf 27 J for full size specimens.S56. Transverse Charpy Impact Energy AbsorptionRequirementS56.1 The transverse Charpy V-notch impact propertiesshall not be less than 20 ftlbf 27 J at the specified tempera-ture.S56.2

38、 Each impact test value shall constitute the averagevalue of three specimens, with not more than one value belowthe specified minimum value of 20 ftlbf 27 J but in no casebelow 15 ftlbf 20 J for full size specimens.SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to th

39、is standard since the last issue(A553/A553M 06) that may impact the use of this standard.(1) Deleted paragraph 3.5.(2) Deleted paragraph 3.2 and renumbered subsequent para-graphs.(3) Revised paragraphs 3.1 and 3.2ASTM International takes no position respecting the validity of any patent rights asser

40、ted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by

41、the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receiv

42、e careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Intern

43、ational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A553/A553M 103