ASTM A523-1996(2005) Standard Specification for Plain End Seamless and Electric-Resistance-Welded Steel Pipe for High-Pressure Pipe-Type Cable Circuits《高压管型电缆线路用平端无缝与电阻焊钢管的标准规范》.pdf

《ASTM A523-1996(2005) Standard Specification for Plain End Seamless and Electric-Resistance-Welded Steel Pipe for High-Pressure Pipe-Type Cable Circuits《高压管型电缆线路用平端无缝与电阻焊钢管的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A523-1996(2005) Standard Specification for Plain End Seamless and Electric-Resistance-Welded Steel Pipe for High-Pressure Pipe-Type Cable Circuits《高压管型电缆线路用平端无缝与电阻焊钢管的标准规范》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 523 96 (Reapproved 2005)Standard Specification forPlain End Seamless and Electric-Resistance-Welded SteelPipe for High-Pressure Pipe-Type Cable Circuits1This standard is issued under the fixed designation A 523; the number immediately following the designation indicates the year ofori

2、ginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers seamless and electric-resistance-we

3、lded steel pipe used as conduit for the installationof high-pressure pipe-type electrical cables in NPS 4 to NPS12, inclusive, with nominal (average) wall thicknesses 0.219 to0.562 in., depending on size. Pipe having other dimensions(Note 2) may be furnished, provided such pipe complies withall othe

4、r requirements of this specification.NOTE 1The dimensionless designator NPS (nominal pipe size) hasbeen substituted in this standard for such traditional terms as “nominaldiameter,” “size,” and “nominal size.”NOTE 2A comprehensive listing of standardized pipe dimensions iscontained in ANSI B36.10.1.

5、2 Pipe ordered under this specification is suitable forwelding and for forming operations involving flaring, belling,and bending.1.3 Pipe for this purpose shall be furnished in Grade A orGrade B as specified in the purchase order. Grade A is moresuitable for forming operations involving bending, fla

6、ring, orbelling and this grade is normally preferred. This provision isnot intended to prohibit the cold bending, flaring, or belling ofGrade B pipe.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that a

7、re provided for information onlyand are not considered standard.1.5 The following hazard caveat applies to the test methodportion, Section 20, of this specification: This standard doesnot purport to address all of the safety concerns, if any,associated with its use. It is the responsibility of the u

8、ser of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:2A 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 751 Test Methods, Practices, and Termin

9、ology forChemical Analysis of Steel ProductsE59 Practice for Sampling Steel and Iron for Determinationof Chemical Composition32.2 ANSI Standard:B36.10 Welded and Seamless Wrought Steel Pipe43. Ordering Information3.1 Orders for material under this specification shouldinclude the following, as requir

10、ed, to describe the desiredmaterial adequately:3.1.1 Quantity (feet or number of lengths),3.1.2 Name of material (steel pipe),3.1.3 Method of manufacture (seamless or electric-resistance-welded),3.1.4 Grade (Table 1),3.1.5 Size (outside diameter and nominal wall thickness orweight per foot),3.1.6 Le

11、ngth when other than specified in Section 13,3.1.7 End finish (Section 16),3.1.8 Skelp for tension tests, if permitted 20.2,3.1.9 When mill applied coating is required (Section 10),and3.1.10 ASTM specification number.4. Process4.1 The steel shall be made by one or more of the followingprocesses: ope

12、n-hearth, basic-oxygen, or electric-furnace.4.2 Steel may be cast in ingots or may be strand cast. Whensteels of different grades are sequentially strand cast, identifi-cation of the resultant transition material is required. The1This specification is under the jurisdiction of ASTM Committee A01 on

13、Steel,Stainless Steel, and RelatedAlloys, and is the direct responsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved Oct. 1, 2005. Published November 2005. Originallyapproved in 1964. Last previous edition approved in 2001 as A 523 96 (2001).This specification w

14、as initiated by the IEEE Insulated Conductors Committee inrecognition of the need for a specification embodying the special requirements ofpipe for high-voltage electrical circuits. It was prepared for acceptance as anASTMspecification by a task group of Subcommittee A01.09 of ASTM Committee A01.2Fo

15、r referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from American National Standards Institute

16、, 11 West 42nd St., 13thFloor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.producer shall remove the transition material by any estab-lished procedure that positively separates the grades.5. Chemical Compositio

17、n5.1 The steel shall conform to the requirements as tochemical composition prescribed in Table 2 and the chemicalanalysis shall be in accordance with Test Methods, Practices,and Terminology A 751.6. Heat Analysis6.1 When specified in the purchase order, the manufacturershall report the heat analysis

18、 of each heat of steel used in themanufacture of pipe to this specification. The analysis shallconform to the requirements specified in Section 5 for thegrade of pipe ordered.7. Product Analysis7.1 When specified in the purchase order, a product analysisreport shall be furnished by the manufacturer

19、on two pipesfrom each lot of 400 lengths, or fraction thereof, of 412-in.outside diameter and 5916-in. outside diameter sizes and fromeach lot of 200 lengths, or fraction thereof, of each size 658-in.outside diameter through 1234-in. outside diameter pipe.Samples for chemical analysis, except for sp

20、ectrographicanalysis, shall be taken in accordance with Practice E59. Thechemical composition thus determined shall conform to therequirements specified in Section 5.7.2 Product Analysis RetestsIf both lengths of pipe rep-resenting the lot fail the specified product analysis, the lot shallbe rejecte

21、d, or at the option of the manufacturer, all of theremaining lengths of the lot shall be tested individually forconformance to the specified requirements. If only one of thelengths of pipe representing the lot fails the specified checkanalysis, the lot shall be rejected or, at the option of themanuf

22、acturer, two retest analyses shall be made on twoadditional lengths selected from the same lot. If both of theseretest analyses conform to the specified requirements, the lotshall be accepted except for the length which failed on theinitial analysis. If one or both of the retest analyses fail thespe

23、cified requirements, the entire lot shall be rejected, or, at theoption of the manufacturer, each of the remaining lengths shallbe tested individually. Only analysis of the rejecting element orelements is necessary in checking the remaining lengths.8. Tensile Requirements8.1 The material shall confo

24、rm to the requirements as totensile properties prescribed in Table 1.8.2 The yield point shall be determined by the drop of thebeam or by the halt in the gauge of the testing machine, by theuse of dividers, or by other approved methods. When a definiteyield point is not exhibited, the yield strength

25、 corresponding toa permanent offset of 0.2 % of the gauge length of thespecimen or to a total extension of 0.5 % of the gauge lengthof the specimen under load shall be determined.8.3 The test specimen taken across the weld shall show atensile strength not less than the minimum tensile strengthspecif

26、ied for the grade of pipe ordered. This test will not berequired for pipe under NPS 8.9. Flattening Test Requirements9.1 Seamless PipeFor seamless pipe, a section not lessthan 212 in. (63.5 mm) in length shall be flattened cold betweenparallel plates in two steps. During the first step, which is a t

27、estfor ductility, no cracks or breaks on the inside or outside or endsurfaces, except as provided for in 9.5, shall occur until thedistance between the plates is less than the value of Hcalculated by the following equation:TABLE 1 Tensile RequirementsGrade A Grade BTensile strength, min, ksi (MPa) 4

28、8 (330) 60 (415)Yield strength, min, ksi (MPa) 30 (205) 35 (240)Elongation in 2 in. or 50 mm, %:Basic minimum elongation for walls516 in. (7.94mm) and over in thickness, longitudinal striptests, and for small sizes tested in full section.35 30When standard round 2-in. or 50-mm gage lengthtest specim

29、en is used28 22For longitudinal strip tests, the width of the gagesection shall be 112 in. (38.1 mm) and adeduction for each132 in. (0.79 mm) decrease inwall thickness below516 in. (7.94 mm) from thebasic minimum elongation of the followingpercentage points1.75A1.50AAThe following tableBgives the mi

30、nimum computed values:Wall Thickness Elongation in 2 in. or 50mm, min, %in. mm Grade A Grade B516 (0.312) 7.94 35.0 30.0932 (0.281) 7.14 33.2 28.514 (0.250) 6.35 31.5 27.0732 (0.219) 5.56 29.8 25.5316 (0.188) 4.76 28.0 24.0532 (0.156) 3.97 26.2 22.518 (0.125) 3.18 24.5 21.0332 (0.094) 2.38 22.8 19.5

31、116 (0.062) 1.59 21.0 18.0BThis table gives the computed minimum elongation values for each132 in.(0.79 mm) decrease in wall thickness. Where the wall thickness lies between twovalues shown above, the minimum elongation value shall be determined by thefollowing equation:Grade EquationABE =56t + 17.5

32、0E =48t + 15.00where:E = elongation in 2 in. or 50 mm, %, andt = actual thickness of specimen, in.TABLE 2 Chemical RequirementsComposition, %Carbon,maxManganese,maxPhosphorus,maxSulfur,maxHeat Product Heat Product Heat Product Heat ProductGrade ASeamless 0.22 0.25 0.90 0.95 0.035 0.045 0.050 0.060E.

33、R.W.A0.21 0.25 0.90 0.95 0.035 0.045 0.050 0.060Grade BSeamless 0.27 0.30 1.15 1.20 0.035 0.045 0.050 0.060E.R.W.A0.26 0.30 1.15 1.20 0.035 0.045 0.050 0.060AElectric-Resistance-Welded pipe.A 523 96 (2005)2H 511e!te1tD(1)where:H = distance between flattening plates, in. (mm),e = deformation per unit

34、 length (constant for a givengrade of steel, 0.09 for GradeAand 0.07 for Grade B),t = specified wall thickness, in. (mm), andD = specified outside diameter, in. (mm).During the second step, which is a test for soundness, theflattening shall be continued until the specimen breaks or theopposite walls

35、 of the pipe meet. Evidence of laminated orunsound material that is revealed during the entire flatteningtest shall be cause for rejection.9.2 Electric-Resistance-Welded PipeAspecimen at least 4in. (101.6 mm) in length shall be flattened cold betweenparallel plates in three steps with the weld locat

36、ed either 0 or90 from the line of direction of force as required in 9.2.1during the first step, which is a test for ductility of the weld, nocracks or breaks on the inside or outside surfaces shall occuruntil the distance between the plates is less than two thirds ofthe original outside diameter of

37、the pipe. As a second step, theflattening shall be continued. During the second step, which istest for ductility exclusive of the weld, no cracks or breaks onthe inside or outside surfaces, except as provided for in 9.5,shall occur until the distance between the plates is less than onethird of the o

38、riginal outside diameter of the pipe but is not lessthan five times the wall thickness of the pipe. During the thirdstep, which is a test for soundness, the flattening shall becontinued until the specimen breaks or the opposite walls of thepipe meet. Evidence of laminated or unsound material or ofin

39、complete weld that is revealed during the entire flattening testshall be cause for rejection.9.2.1 For pipe produced in single lengths, the flattening testspecified in 9.2 shall be made on both crop ends cut from eachlength of pipe. The tests from each end shall be madealternately with the weld at 0

40、 and at 90 from the line ofdirection of force. For pipe produced in multiple lengths, theflattening test shall be made on crop ends representing the frontand back of each coil with the weld at 90 from the line ofdirection of force, and on two intermediate rings representingeach coil with the weld 0

41、from the line of direction of force.9.3 Surface imperfections in the test specimen before flat-tening, but revealed during the first step of the flattening test,shall be judged in accordance with the finish requirements inSection 15.9.4 Superficial ruptures as a result of surface imperfectionsshall

42、not be cause for rejection.9.5 When low D-to-t ratio tubulars are tested, because thestrain imposed due to geometry is unreasonably high on theinside surface at the 6 and 12 oclock locations, cracks at theselocations shall not be cause for rejection if the D-to-t ratio isless than ten.10. Coatings10

43、.1 Unless otherwise specified, the pipe shall not be givena mill coating of paint, oil, or any other material either insideor outside.11. Dimensions and Weight11.1 Dimensions and weight of pipe included in this speci-fication are listed in Table 3.12. Dimensions, Weight, and Permissible Variations12

44、.1 WeightThe weight of the pipe as specified in Table 3shall not vary by more than the following amounts:Extra-strong and lighter wall thickness 65%Minimum permissible length 610 %12.2 DiameterThe outside diameter shall not vary morethan 61 % from the diameter specified. Pipe NPS 10 andsmaller shall

45、 not be more than164 in. (0.4 mm) smaller andNPS 12 pipe shall not be more than132-in. (0.8-mm) smallerthan the tabulated outside diameter for a distance of 4 in.(101.6 mm) from the end. The pipe shall permit passage overthe ends for a distance of 4 in. of a ring gauge having a bore116-in. larger th

46、an the tabulated diameter of NPS 10 andsmaller pipe, and a bore332 in. (2.4 mm) larger for NPS 12pipe.TABLE 3 Dimensions, Weight, and Test PressuresNPSDesig-natorOutsideDi-ameter,in.WallThicknessNominalWeightTest PressureGrade A Grade Bin. mm lb/ft kg/m psi MPa psi MPa4412 0.237 6.02 10.79 16.1 1900

47、 13.10 2200 15.170.250 6.35 11.35 16.9 2000 13.79 2300 15.860.281 7.14 12.66 18.8 2200 15.17 2500 17.240.312 7.92 13.96 20.7 2500 17.24 2500 17.2455916 0.219 5.56 12.50 18.6 1400 9.65 1700 11.720.258 6.55 14.62 21.8 1700 11.72 1900 13.100.281 7.14 15.85 23.6 1800 12.41 2100 14.480.312 7.92 17.50 26.

48、0 2000 13.79 2400 16.550.344 8.74 19.17 28.6 2200 15.17 2500 17.246658 0.250 6.35 17.02 25.3 1400 9.65 1600 11.030.280 7.11 18.97 28.2 1500 10.34 1800 12.410.312 7.92 21.04 31.3 1700 11.72 2000 13.790.344 8.74 23.08 34.3 1900 13.10 2200 15.170.375 9.52 25.03 37.2 2000 13.79 2400 16.550.500A12.70A32.

49、71A48.7A2500 17.24 2500 17.248858 0.250 6.35 22.36 33.3 1000 6.89 1200 8.270.277 7.04 24.70 36.8 1200 8.27 1300 8.960.312 7.92 27.70 41.2 1300 8.96 1500 10.340.322 8.18 28.55 42.6 1300 8.96 1600 11.030.344 8.74 30.42 45.3 1400 9.65 1700 11.720.375 9.52 33.04 49.2 1600 11.03 1800 12.410.438 11.13 38.30 57.0 1800 12.41 2100 14.480.500 12.70 43.39 64.6 2100 14.48 2400 16.5510 1034 0.250 6.35 28.04 41.7 850 5.86 1000 6.890.279 7.09 31.20 46.4 1000 6.89 1200 8.270.307 7.80 34.24 50.9 1000 6.89 1200 8.270.344 8.74 38.23 56.9 1100 7.58 1300 8.960.36