ASTM A36 A36M-2012 Standard Specification for Carbon Structural Steel《碳素结构钢的标准规格》.pdf

《ASTM A36 A36M-2012 Standard Specification for Carbon Structural Steel《碳素结构钢的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A36 A36M-2012 Standard Specification for Carbon Structural Steel《碳素结构钢的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A36/A36M 08A36/A36M 12Standard Specification forCarbon Structural Steel1This standard is issued under the fixed designation A36/A36M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number

2、in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification2 covers carbon steel shapes, plates, and

3、bars of structural quality for use in riveted, bolted, or weldedconstruction of bridges and buildings, and for general structural purposes.1.2 Supplementary requirements are provided for use where additional testing or additional restrictions are required by thepurchaser. Such requirements apply onl

4、y when specified in the purchase order.1.3 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to beutilized. See Appendix X3 of Specification A6/A6M for information on weldability.1.4 The values stated in either inch-pound units or SI u

5、nits are to be regarded separately as standard. Within the text, the SI unitsare shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be usedindependently of the other, without combining values in any way.1.5 The text of this specification conta

6、ins notes or footnotes, or both, that provide explanatory material. Such notes andfootnotes, excluding those in tables and figures, do not contain any mandatory requirements.1.6 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additio

7、nalrequirements, including additional testing requirements and the reporting of additional test results, of A6/A6M apply.2. Referenced Documents2.1 ASTM Standards:3A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet PilingA27/A27M Specification f

8、or Steel Castings, Carbon, for General ApplicationA307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile StrengthA325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile StrengthA325M Specification for Structural Bolts, Steel, Heat Trea

9、ted 830 MPa Minimum Tensile Strength (Metric)A500 Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and ShapesA501 Specification for Hot-Formed Welded and Seamless Carbon Steel Structural TubingA502 Specification for Rivets, Steel, StructuralA563 Specificatio

10、n for Carbon and Alloy Steel NutsA563M Specification for Carbon and Alloy Steel Nuts (Metric)A668/A668M Specification for Steel Forgings, Carbon and Alloy, for General Industrial UseA1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-S

11、trength Low-Alloy with Improved Formability, and Ultra-High StrengthA1018/A1018M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing,Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High StrengthF56

12、8M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric) (Withdrawn 2012)4F1554 Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys an

13、d is the direct responsibility of Subcommittee A01.02on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.Current edition approved May 15, 2008Nov. 1, 2012. Published June 2008 December 2012. Originally approved in 1960. Last previous edition approved in 20052008 asA36/A36M 05.A36/A36

14、M 08. DOI: 10.1520/A0036_A0036M-08.10.1520/A0036_A0036M-12.2 For ASME Boiler and Pressure Vessel Code Applications, see related Specifications SA-36 in Section II of that Code.3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For

15、 Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.4 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard

16、an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is

17、to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13. Appurtenant Materials3.1 When components of a steel structure are identified wi

18、th this ASTM designation but the product form is not listed in thescope of this specification, the material shall conform to one of the standards listed in Table 1 unless otherwise specified by thepurchaser.4. General Requirements for Delivery4.1 Structural products furnished under this specificatio

19、n shall conform to the requirements of the current edition ofSpecification A6/A6M, for the specific structural product ordered, unless a conflict exists in which case this specification shallprevail.4.2 Coils are excluded from qualification to this specification until they are processed into a finis

20、hed structural product.Structural products produced from coil means structural products that have been cut to individual lengths from a coil. Theprocessor directly controls, or is responsible for, the operations involved in the processing of a coil into a finished structuralproduct. Such operations

21、include decoiling, leveling or straightening, hot-forming or cold-forming (if applicable), cutting to length,testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.NOTE 1For structural products produced from coil and furnished w

22、ithout heat treatment or with stress relieving only, two test results are to be reportedfor each qualifying coil. Additional requirements regarding structural products produced from coil are described in Specification A6/A6M.5. Bearing Plates5.1 Unless otherwise specified, plates used as bearing pla

23、tes for bridges shall be subjected to mechanical tests and shall conformto the tensile requirements of Section 8.5.2 Unless otherwise specified, mechanical tests shall not be required for plates over 112 in. 40 mm in thickness used asbearing plates in structures other than bridges, subject to the re

24、quirement that they shall contain 0.20 to 0.33 % carbon by heatanalysis, that the chemical composition shall conform to the requirements ofTable 3 in phosphorus and sulfur content, and that aTABLE 1 Appurtenant Material SpecificationsNOTE 1The specifier should be satisfied of the suitability of thes

25、ematerials for the intended application. Chemical composition or mechani-cal properties, or both, may be different than specified in A36/A36M.Material ASTM DesignationSteel rivets A502, Grade 1Bolts A307, Grade A or F568M, Class 4.6High-strength bolts A325 or A325MSteel nuts A563 or A563MCast steel

26、A27/A27M, Grade 6535 450240Forgings (carbon steel) A668/A668M, Class DHot-rolled sheets and strip A1011/A1011M, SS Grade 36 250 Type1 or Type 2 or A1018/A1018M, SS Grade36 250Cold-formed tubing A500, Grade BHot-formed tubing A501Anchor bolts F1554, Grade 36TABLE 2 Tensile RequirementsAPlates, Shapes

27、,B and Bars:Tensile strength, ksi MPa 5880 400550Yield point, min, ksi MPa 36 250CPlates and Bars:D,EElongation in 8 in. 200 mm, min, % 20Elongation in 2 in. 50 mm, min, % 23Shapes:Elongation in 8 in. 200 mm, min, % 20Elongation in 2 in. 50 mm, min, % 21BA See the Orientation subsection in the Tensi

28、on Tests section of SpecificationA6/A6M.B For wide flange shapes with flange thickness over 3 in. 75 mm, the 80 ksi 550MPa maximum tensile strength does not apply and a minimum elongation in 2 in.50 mm of 19 % applies.C Yield point 32 ksi 220 MPa for plates over 8 in. 200 mm in thickness.D Elongatio

29、n not required to be determined for floor plate.E For plates wider than 24 in. 600 mm, the elongation requirement is reduced twopercentage points. See the Elongation Requirement Adjustments subsectionunder the Tension Tests section of Specification A6/A6M.A36/A36M 122sufficient discard shall be made

30、 to secure sound plates.6. Materials and Manufacture6.1 The steel for plates and bars over 12 in. 12.5 mm in thickness and shapes with flange or leg thicknesses over 1 in. 25 mmshall be semi-killed or killed.shall be killed7. Chemical Composition7.1 The heat analysis shall conform to the requirement

31、s prescribed in Table 3, except as specified in 5.2.7.2 The steel shall conform on product analysis to the requirements prescribed in Table 3, subject to the product analysistolerances in Specification A6/A6M.8. Tension Test8.1 The material as represented by the test specimen, except as specified in

32、 5.2 and 8.2, shall conform to the requirements asto the tensile properties prescribed in Table 2.8.2 Shapes less than 1 in.2 645 mm2 in cross section and bars, other than flats, less than 12 in. 12.5 mm in thickness ordiameter need not be subjected to tension tests by the manufacturer, provided tha

33、t the chemical composition used is appropriatefor obtaining the tensile properties in Table 2.9. Keywords9.1 bars; bolted construction; bridges; buildings; carbon; plates; riveted construction; shapes; steel; structural steel; weldedconstructionSUPPLEMENTARY REQUIREMENTSThese requirements shall not

34、apply unless specified in the order.Standardized supplementary requirements for use at the option of the purchaser are listed inSpecification A6/A6M. Those that are considered suitable for use with this specification are listed bytitle:TABLE 3 Chemical RequirementsNOTE 1Where “. . .” appears in this

35、 table, there is no requirement. The heat analysis for manganese shall be determined and reported as describedin the heat analysis section of Specification A6/A6M.Product ShapesA PlatesB BarsBThickness, in. mm AllTo 3420,inclOver 34to 11220 to 40,inclOver 112to 21240 to 65,inclOver 212to 465 to 100,

36、inclOver 4100To 3420,inclOver 34to 11220 to 40,inclOver 112to 4100,inclOver 4100Carbon, max, % 0.26 0.25 0.25 0.26 0.27 0.29 0.26 0.27 0.28 0.29Manganese, % . . 0.801.20 0.801.20 0.851.20 0.851.20 . 0.600.90 0.600.90 0.600.90Phosphorus, max, % 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04 0.04Sulfur,

37、 max, % 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05Silicon, % 0.40 max 0.40 max 0.40 max 0.150.40 0.150.40 0.150.40 0.40 max 0.40 max 0.40 max 0.40 maxCopper, min, % whencop per steel is specified0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20A Manganese content of 0.851.35 % and silicon con

38、tent of 0.150.40 % is required for shapes with flange thickness over 3 in. 75 mm.B For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese above the specified maximum willbe permitted, up to the maximum of 1.35 %.A36/A36M 123S5.

39、Charpy V-Notch Impact Test.S30. Charpy V-Notch Impact Test for Structural Shapes: Alternate Core LocationS32. Single Heat BundlesS32.1 Bundles containing shapes or bars shall be from a single heat of steel.In addition, the following optional supplementary requirement is also suitable for use with th

40、is specification:S97. Limitation on Rimmed or Capped SteelS97.1 The steel shall be other than rimmed or capped.SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue(A36/A36M 05A36/A36M 08) that may impact the use of this standard. (Appr

41、oved May 15, 2008Nov. 1,2012.)(1) Added informationModified 6.1 to Table 1 on forgings (carbon steel) and anchor bolts.allow killed steel only.(2) Removed S97 and S97.1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin

42、this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must

43、 be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of there

44、sponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700,

45、West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A36/A36M 124