ARMY MIL-W-53122-1992 WATER PURIFICATION UNIT REVERSE OSMOSIS 3 000 GPH《3000加仑每小时型反渗透水净化装置》.pdf

《ARMY MIL-W-53122-1992 WATER PURIFICATION UNIT REVERSE OSMOSIS 3 000 GPH《3000加仑每小时型反渗透水净化装置》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-W-53122-1992 WATER PURIFICATION UNIT REVERSE OSMOSIS 3 000 GPH《3000加仑每小时型反渗透水净化装置》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-W-53122 46 W 9997906 0508325 9 W I INCH-POUND I 31 January 1992 MIL-W-53122(ME) MILITARY SPECIFICATION WATER PURIFICATION UNIT REVERSE OSMOSIS, 3,000 GPH This specification is approved for use within the USA Belvoir Research, Development, and Engineering Center, Department of the Army, and is av

2、ailable for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 ScoDe. This specification defines a trailer mounted reverse osmosis water purification unit hereinafter referred to as “ROWPU“, having a water production rate (see 6.7.d). of 60,000 gallons per day (GPD) with

3、minimum average flow rate of 3,000 gallons per hour (GPH) when processing fresh/brackish water and 40,000 GPD with a minimum of 2,000 GPH when processing salt water (all water flow corrected to 77 OF by using appropriate RO element manufacturer normalization chart). 2. APPLICABLE DOCUMENTS 2.1 Gover

4、nment documents. 2.1.1 SPecifications and standards. The following specifications and standards form a part of this document to the extent specified herein. otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Stand

5、ards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Unless Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: USA Belvoir Research, Development, and Engineering Center, ATTN:

6、 STRBE-TSE, Fort Belvoir, VA 22060-5606 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 4610 DISTRIBUTION STATEMENT A. un1 imi ted. Approved for public release; distribution is Provided by IHSNot for ResaleNo

7、reproduction or networking permitted without license from IHS-,-,-MIL-W-53122 46 m 06 0508326 O m MI L-W-53122 (ME) SPECIFICATIONS FEDERAL ZZ-H-451 ZZ-H-561 PPP-B-601 PPP-B-636 PPP- B- 1055 PPP-P-40 PPP-T-76 MI LI TARY MI L-P- 116 MI L-B-121 MI L-V-173 MI L-P-514 MI L-T-704 MIL-L-2104 MI L-F-3541 MI

8、L-G-3859 MIL-W-6858 MIL-B-7883 MIL-P-10603 MIL-P-19834 MIL-L-21260 MIL-C-22750 MIL-G-23827 MIL-G-28554 MIL-L-46167 MIL-C-46168 MIL-P-53022 MI L-P-53030 - Hose, Fire, Woven-Jacketed Rubber or Latex or Rubber-Coated Fabric-Lined, with Couplings. - Hose, Rubber, and Hose Assemblies, Rubber, Smooth Bore

9、, Water Suction and Discharge. - Boxes, Wood, Cleated Plywood. - Boxes, Shipping, Fiberboard. - Barri er Materi al , Waterproofed, F1 exi bl e. - Packaging and Packing of Hand Tools. - Tape, Pressure-Sensi tive Adhesive Paper, (for Carton Seal i ng) . f c a - Preservation, Methods of. - Barrier Mate

10、ri al , Greaseproofed, Waterproofed, F1 exi bl e. - Varnish, Moisture and Fungus Resistant (for Treatment of Communi cat i on , El ectroni cy and Associated Equipment). - Plates, Identification, Instruction and Marking, B1 ank. - Treatment and Painting Materiel. - Lubricating Oil , Internal Combusti

11、on Engine, Tact i cal Servi ce. - Fittings, Lubrication. - Grease Guns, Hand-Operated, Lever, Push and Screw Type - Welding, Resistance, Spot and Seam. - Brazing of Steels, Copper, Copper Alloys, Nickel Al 1 oys , Al umi num and Al umi num Al 1 oys . - Pumps and Pumping Units, Centrifugal , Power-Dr

12、iven, for Water, Packaging of. - Plates, Identification, Metal Foil , Adhesive Backed. - Lubricating Oil Internal Combustion Engine Preservat i ve Break. - Coating, Epoxy Polyamide. - Grease, Aircraft and Instrument, Gear and Actuator Screw, NATO CODE 6-354, Metric. - Generator Sets, Mobile Electric

13、 Power, Packaging of. - Lubricating Oil Internal Combustion Engine Arctic. - Coating, Aliphatic Polyurethane, Chemical Agent - Primer Epoxy Coating Corrosion Inhibitive Lead and - Primer Coating Epoxy Water. Reducible Lead and Resi stant. Chromate Free. Chromate Free. 2 Provided by IHSNot for Resale

14、No reproduction or networking permitted without license from IHS-,-,-. MIL-W-53122 46 9999906 0508327 2 MIL-W-53122 (ME) MIL-C-53039 MIL-C-53072 MIL-P-53084 MIL-V-62038 STANDARDS FEDERAL FED-STD-313 FED-STD-595 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-130 MIL-STD-209 MIL-STD-454 MIL-STD-461 MIL-STD-

15、462 MIL-STD-810 MIL-STD-889 MIL-STD-1186 MIL-STD-1472 MIL-STD-1474 MIL-STD-1791 MIL-STD-6866 MIL-STD-11991 MS35844 MS49006 - Coating Aliphatic Polyurethane Single Component. - Chemical Agent Resistant Coating (CARC) System - Primer Cathodic Electrodeposition CARC. - Vehicles, Wheeled, Preparation fo

16、r Shipment and Appl i cati on Procedures and Qual i ty Control Inspection. Storage. - Material Safety Data Sheets. - Colors used in Government Procurement. - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage. - Identification Marking of U.S. Military Property. - Sli

17、ng and Tie-down Provisions for Lifting and Tying Down Military Equipment. - Standard General Requirements for Electronic Equipment. - Electromagnetic Emission and Susceptibility Requirements for the Control of Electromagnetic Interference. - Electromagnetic Interference Characteristics Measurement O

18、f. - Environmental Test Methods and Engineering Guidelines. - Di ssimi 1 ar Metal s. - Cushioning, Anchoring, Bracing, Blocking and Waterproofing; with Appropriate Test Methods. - Human Engineering Design Criteria for Military Systems, Equipment and Facilities. - Noise Limits for Military Materiel.

19、- Design for Internal Aerial Delivery in Fixed Wing Aircraft . - Inspection, Liquid Penetrant. - El ectri cal , Electronic and El ectro-Mechani cal Equipment, Guided Missile and Associated Weapon Systems, General Standard for the Design of. - Plug, Machine Thread, Magnetic (Drain). - Plug, Pipe, Mag

20、netic-Headless, Aluminum, Iron or Steel. Attributes. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-53122 46 9 9999906 0508328 4 9 MI L-W-53122 (ME) (Unless otherwise indicated, copies of federal and military specifications and standards are

21、 available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawincls. and Publications. The following other Government documents, drawings, and pub1 ications form a part of this document to the extent spe

22、cified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAW I NG TA13229E0000 - Water Purification Unit, Reverse Osmosis, Trailer- 13229E 13 78 Mounted, 3,000 GPH, - Overpack Assembly, 3000 GPH ROWPU. (Copies of drawings required by contractors in connection with.

23、specific acquisition functions should be obtained from the USA Belvoir Research. Development, and Engineering Center, ATTN: STRBE-FSQ, Fort Belvoir, VA 22060-5606.) INTER-GOVERNMENTAL MARTIME ORGANIZATION International Convention for Safe Containers (SCS) (Applicatioon for copies should be addressed

24、 to the Commandant, (G-MVI), US Coast Guard, 2100 Second Street, SW Washington, DC 20593.) CODE OF FEDERAL REGULATIONS Title 21, Food and Drug Additives, Parts 170 to 199. Title 29, Chapter XVII, Part 1910. Title 49, Parts 170 to 190. (Application for copies should be made to the Superintendent of D

25、ocuments, Government Printing Office, Washington, DC 20402,) DEPARTMENT OF ARMY TECHNICAL BULLETIN TB MED 577 - Sanitary Control and Surveillance of Field (Application for copies should be made to the Commander, US Army AG Installation Water Supplies. Pub1 ications Center, 2800 Eastern Boulevard, Ba

26、ltimore, MD 21220.) PUBLICATIONS (C) ABCA Agreement (QSTAG 244) (C) ABCA Agreement (QSTAG 747) - Nuclear Survivability Criteria for Military Equipment. (U) - Nucl ear Comtami nat i on Survi vabi 1 i ty Criteria for Military Equipment. (U) 4 Provided by IHSNot for ResaleNo reproduction or networking

27、permitted without license from IHS-,-,-MIL-U-53122 4b = 9999906 0508329 b S (Application for copies of the QSTAG should be addressed to the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government Publications. The following documents fo

28、rm a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. of documents not listed in the DODISS are the issues of the documents cited in the solicitat

29、ion (see 6.2). Unless otherwise specified, the issues AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI/IEEE 315 - Graphic Symbols for Electrical and Electronic Diagrams (Including Reference Designation Class Designation Letters). (Application for copies should be addressed to the American National

30、andards Institute, 1430 Broadway, New York, NY 10018.) AMERICAN SOCIETY FOR NON-DESTRUCTIVE TESTING (ASNT) ASNT-TC-1A Recommended Practice - Non-Destructive Testing Personnel Qualifications and Certification - Supplement Dy (Liquid Penetrant). (Application for copies should be addressed to the Ameri

31、can Society for Non- Destructive Testing, 4153 Arlingate Plaza, Columbus, OH 43228.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 1141 D 3951 D 3953 D 4675 - Substitute for Ocean Water. - Standard for Commercial Packaging. - Strapping, Flat Steel and Seals. - Selection and Use of Flat Strappi

32、ng Materials. (Application for copies should be addressed to the American Society for Testing and Materials, 1915 Race Street, Philadelphia, PA 19103.) AMERICAN SOCIETY OF MECHANICAL ENGINEERS (ASME) Boiler and Pressure Vessel Code, Section IX, Qualification Standard for We1 di ng and Brazi ng Proce

33、dures , We1 ders , Brazers , and We1 ding and Brazi ng Operators. (Application for copies should Mechanical Engineers, United Eng York, NY 10017.) be addressed to the American Society of neering Center, 354 East 47th Street, New 5 Provided by IHSNot for ResaleNo reproduction or networking permitted

34、without license from IHS-,-,-MIL-W-53122 i.16 M 9999906 0508330 2 MIL-W-53122(ME) AMERICAN WELDING SOCIETY (AWS) A5.1 - Covered Carbon Steel Arc Welding Electrodes. A5.9 - Corrosion Resisting Chromium and Chromium-Nickel Steel Bare and Composite Metal Cored and Stranded Welding Electrodes and Weldin

35、g Rods. A5.10 - Bare Aluminum and Aluminum-Alloy Electrodes and Rods. A5.18 - Steel , Carbon, Filler Metals for Gas Shielded Arc Welding. A5.28 - Low-Alloy Steel Filler Metals for Gas Shielded Arc Welding. D1.l - Structural Welding Code - Steel. D1.2 - Structural Welding Code - Aluminum. (Applicatio

36、n for copies should be addressed to the American Welding Society, ASSOCIATION OF AMERICAN RAILROADS (AAR) 550 North LeJeune Road, P.O. Box 351040, Miami, FL 33126.) Rules Governing Loading of Commodities on Open Top Cars. (Application for copies should be addressed to the Association of American INT

37、ERNATIONAL STANDARDS ORGANIZATION (ISO) Railroads, 59 East Van Buren Street, Chicago, IL 60605.) IS0 1496-1 - Series 1 Freight Containers - Specification and Testing - Part 1: General Cargo Containers for General Purposes. (Application for copies should be addressed to the American National NATIONAL

38、 FIRE PROTECTION AGENCY (NFPA) Standards Institute, Inc., 1430 Broadway, New York, NY 10018.) National Electrical Code - NFPA 70, Article 310. (Application for copies should be addressed to the National Fire Protection Agency, Batterymarch Park, Quincy, MA 02269.) SOCIETY OF AUTOMOTIVE ENGINEERS (SA

39、E) 5185 5429 - Mechanical and Material Requirements for Externally Threaded Fasteners. 5492 - Rivets and Riveting. - Access Systems for Off-Road Machines. (Application for copies should be addressed to the Society of Automotive Eng i neers , 400 Commonweal t h Dri ve , Warrendal e, PA 15096. ) 6 Pro

40、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-53L22 46 m 9999906 0508333 4 m MI L-W-53 122 (ME) SOUTH COAST AIR QUALITY MANAGEMENT DISTRICT (SCAQMD) Rule 442 - Usage of Solvents. (Application for copies should be addressed to the South Coast Air

41、 Quality (Non-Government standards and other publications are normally available from Management District, 9150 East Flair Drive, El Monte, CA 91731.) the organizations that prepare or distri bute the documents. also may be available in or through libraries or other informational services.) These do

42、cuments 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, (except for related associated detail specifications, specification sheets or MS standards), the text of this document takes precedence. Nothing in this document, however, s

43、upersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 DescriDtion. The 3,000 GPH ROWPU shall be in accordance with Top 3.1.1 Drawinqs. Assembly Drawing TA13229E0000 and as speci fi ed herein. product drawings. is permissible without prior approv

44、al of the contracting officer. tolerances could cumulatively result in incorrect fits, the contractor shall provide tolerances within those prescribed on the drawings to ensure correct fit, assembly, and operation of the ROWPU. Any data (e.g., shop drawings, 1 ayouts, flow sheets, processing procedu

45、res, etc.) prepared by the contractor or obtained from a vendor to support fabrication and manufacture of the production item shall be made available, upon request, for inspection bythe contracting officer or the designated representative. The drawings forming a part of this specification are end No

46、 deviations from the prescribed dimensions or tolerances Where 3.1.2 IS0 container desiqn reauirements. The units shall meet the IS0 3.1.2.1 Certification. Each container shall be certified as required by 1496-1 requirements. the International Convention of Safe Containers and bear evidence of such

47、certification (see 3.16.2 and 4.6.2). to first article inspection (see 6.4), in accordance with 4.3. 3.2 First article. When specified (see 6.2), a sample shall be subjected 3.3 Material. Material shall be as specified herein and on the applicable drawings. Materials not specified shall be selected

48、by the contractor and be subject to all provisions of this specification. adverse effect on the health of personnel when used for its intended purpose. The lines and all surfaces that come in contact with potable water shall conform to the Food, Drug, and Cosmetic, Food Additives (chapter 1, title 2

49、1, 7 The material shall have no Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_. MIL-W-53122 4b 999990b 0508332 b Code of Federal Regulations), for contact with food. sections 177.1020, 177.1040, 177.1050, and 177.1480 of the Food, Drug, and Cosmetic, Indirect Food Additives (chapter 1, title 21, Code of Federal Regulations) shall not be acceptable materials. Questions pertinent to this effo