ARMY MIL-I-51466-1980 IGNITER《引爆装置》.pdf

《ARMY MIL-I-51466-1980 IGNITER《引爆装置》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-I-51466-1980 IGNITER《引爆装置》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-I-53Ybh 13 m 9999906 0334233 O =- MILITARY SPECIFICATION TS-37-/? MIL-1-51466 (EA) 14 April 1980 * IGNITER This specification is approved for use by US Army Armament Research and Development Command, Department of the Amy and is available for use by all Depart- ments and Agencies of the Departme

2、nt of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of igniter. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents of the issue in ef- fect on date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein

3、: STANDARDS FEDEML FED-STD-123 - Marking for Shipment (Civil Agencies). MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection bv Attributes. MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-147 - Palletized and Containerized Unit Loads 40“ bv 48“ MIL-STD-1167 - Ammunition Data

4、Cards. MIL-STD-1168 - Lot Numbering of Ammunition. Pallets, Skids, Runners OP Pallet-Type Base. FSC 1365 : Beneficial comments (recommendations, additions, deletions) and any : pertinent data which may be of use in improving this document should be : : addressed to: Commander, US Army Armament Resea

5、rch and DeveloDment : Command, ATTN: DRDAR-TSC-S, Aberdeen Proving Ground, MD 21010 by us- : : ing the self-addressed Standardization Document Imgrovement Proposal : : (DD Form 1426) appearing at the end of this document or by letter. I THIS DOCUMENT CONTAINS (p PAGES. , Provided by IHSNot for Resal

6、eNo reproduction or networking permitted without license from IHS-,-,- MIL-I-51466(EA) MIL-I-514bb 13 M 7777706 0334212 2 DRAWINGS AND TECHNICAL DATA PACKAGE (TDPL) US ARMY ARMAMENT RESEARCH AND DEVELOPMENT COMMAND CHEMICAL SYSTEMS LABORATORY TDPL 36-2-104 - Igniter. (Copies of specifications, stand

7、ards, drawings and publications re- quired by contractors in connection with snecific procurement functions should be obtained from the procuring activity or as directed by the. contracting officer.) 3. REQUIREMENTS -. 3.1 Materials and components. 3.1.1 Materials. All materials cited on TDPL 36-2-1

8、04 or on the sub- sidiary drawings shall conform to the specifications listed thereon or to the specific characteristics set forth on the drawings. 3.1.2 Components. All components of the igniter shall conform to the specifications and drawings listed on TDPL 32-3-104 and on the subsidiary drawings.

9、 3.2 Assembly. The igniter shall be assembled as shown on C36-2-104. 3.3 Filling. 3.3.1 Delay mixture, The delay mixture shall conform to C143-2-5. 3.3.2 First fire mixture. The first fire mixture shall conform to B143-9-2. 3.4 Loading. The igniter shall be.loaded with a delay mixture with a first f

10、ire pellet placed at each end in such a manner as to insure a hard adhesive plug (see 6.3). 3.5 Functioning. The igniter shall ignite and burn to completion for not less than 10 nor more than 20 seconds when tested in accordance with 4.4.4. 3.6 Preproduction. Prior to the start of regular production

11、, a prepro- duction lot of igniters shall be produced for examination and tests in accordance with this specification. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-use. 4. QUALITY ASSURANCE PROVSTnNS I (a) Preproduction inspection (4.3). (b) Quali

12、tv ConformanFe inQnno+rr+ ii I, , .-“, yulllGLA auu processes as will be used during regular production. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-I-534bbL3 = 779990b 0334234 b 4.4 Quality conformance inspection. 4.4.1 Lotting. A lot of i

13、gniters shall be identified and controlled in accordance with MIL-STD-1167 and with MIL-STD-1168, produced by one manufacturer from the same materials and under essentially the same manu- facturing conditions. 4.4.2 Sampling, 4.4.2.1 For examination. Sampling shall be conducted in accordance with MI

14、L-STD-105. 4.4.2.2 For destructive test. Sampling shall be conducted on the S-4 level of MIL-STD-105. 4.4.3 Inspection procedure. 4.4.3.1 For examination. The igniter shall be examined in accordance with the classification of defects and with MIL-STD-105. 4.4.3.2 For destructive test. Each sample ig

15、niter shall be tested in accordance with 4.4.4, using an AQL of 1% in MIL-STD-105. 4.4.3.3 Classification of defects. (a) Igniter (Drawing C36-2-104). Categories Defects Critical : None defined Major: AQL 0,65 percent defective 101 Filling missing, separated or 102 Thread missing or incorrect 103 Fi

16、rst fire mixture missing cavitated (Dwg C36-2-106) or inadequate . AQL 1.0 percent defective 104 Inside diameter incorrect 105 Chamfer missing 106 Length incorrect 107 Outside diameter incorrect 108 Workmanship ( 3.7 1 -_r . 4 Provided by IHSNot for ResaleNo reproduction or networking permitted with

17、out license from IHS-,-,- t MIL-I-SLVbb 13 = 97799Ob 0334235 MIL-I-S1466(EA) 4.4.4 Functioning test. The igniter shall be assembled to a fuze adapter (see 6.4) in an upright position with the threaded end down inside a fuze adapter so that the upper surface of the tube is not less than 1/2 inch from

18、 the bottom of the fuze. from the spit of the fuze to the ejection of the lower plug ofthe igniter checked by means of a stop watch. observed to be the result of the fuze, a second fuze may be utilized A fuze shall be fired and the burning time If failure of the igniter to fire is 5, PACKAGING 5.1 I

19、nterplant shipment. A designated quantity of igniters shall be packaged and packed to prevent damage in shipment from the supply source to the first receiving activity ox immediate use or further processing. Shipping containers shall be in compliance with the rules and regulations applicable to the

20、mode of transportation. 5.2 Palletization. When specified in the contract or order, igniters shall be palletized in accordance with MIL-STD-147. 5.3 Marking. tract or order, shipping containers shall be marked in accordance with FED-STD-123 and shall include the contract or purchase order number and

21、 name and address of the prime contractor. marked in accordance with MIL-STD-129. In addition to any special marking required by the con- Palletized loads shall be 6, NOTES 6.1 Intended use. The item covered by this specification is intended for use in assembling the M4A2 floating smoke pot. 6.2 Ord

22、ering data. Procurement documents should specify the following: (a) (b) Preproduction. Title, number and date of this specification. (i) Government test and evaluation after award of contract. (2) tions when testing is performed by the Government. (3) tor whether to proceed with production. Time all

23、owed for contractor submission of samples for Name and address of test facility and shipping instruc- Time required for the Government.to notify the contrac- 6.3 Loading. A minimum of 18 grams of delay mixture is required to 1.00 f .O15 grams of first fire mix obtain a satisfactory delay time. can b

24、e placed in each end of the tube. should be pelletized prior to assembly and reconsolidated in the tube in a manner to provide a hard adhesive plug with no separating between pellets. Both first fire mix and delay Provided by IHSNot for ResaleNo reproduction or networking permitted without license f

25、rom IHS-,-,-MIL-I-51466(EA) 6.4 Test accessories. The 207A1 floating smoke pot fuze conforming to MIL-F-51466 and the fuze adapter conforming to Drawing D36-2-67 may be obtained from the contracting officer on request. 6.5 Precaution, This specification covers sampling and testing of chemical toxic

26、or explosive materials which are potentially hazardous to personnel, Aocordingly, it is emphasized that all applicable safety rules, regulations and procedures must be followed in handling and processing these materials, Custodian: Army - EA Preparing activity: Army - EA Project No. 1365-A068 c 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-