ANSI INCITS ISO IEC 25434-2008 Information technology - Data interchange on 120 mm and 80 mm optical disk using +R DL format - Capacity 8 55 Gbytes and 2 66 Gbytes per side (record.pdf

《ANSI INCITS ISO IEC 25434-2008 Information technology - Data interchange on 120 mm and 80 mm optical disk using +R DL format - Capacity 8 55 Gbytes and 2 66 Gbytes per side (record.pdf》由会员分享，可在线阅读，更多相关《ANSI INCITS ISO IEC 25434-2008 Information technology - Data interchange on 120 mm and 80 mm optical disk using +R DL format - Capacity 8 55 Gbytes and 2 66 Gbytes per side (record.pdf（188页珍藏版）》请在麦多课文档分享上搜索。

1、INCITS/ISO/IEC 25434:20082009 (ISO/IEC 25434:2008, IDT) Information technology Datainterchange on 120 mm and 80 mmoptical disk using +R DL format Capacity: 8,55 Gbytes and 2,66 Gbytesper side (recording speed up to 16X)INCITS/ISO/IEC 25434:20082009(ISO/IEC 25434:2008, IDT)INCITS/ISO/IEC 25434:200820

2、09 ii ITIC 2009 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the

3、 editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file ca

4、n be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretaria

5、t at the address given below. Adopted by INCITS (InterNational Committee for Information Technology Standards) as an American National Standard. Date of ANSI Approval: 3/4/2009Published by American National Standards Institute, 25 West 43rd Street, New York, New York 10036 Copyright 2009 by Informat

6、ion Technology Industry Council (ITI). All rights reserved. These materials are subject to copyright claims of International Standardization Organization (ISO), International Electrotechnical Commission (IEC), American National Standards Institute (ANSI), and Information Technology Industry Council

7、(ITI). Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ITI. All requests pertaining to this standard should be submitted to ITI, 1250 Eye Street NW, Washington, DC 20005. Printed in the Unite

8、d States of America INCITS/ISO/IEC 25434:20082009 ITIC 2009 All rights reserved iii Contents Page Foreword ix Introduction .x 1 Scope 1 2 Conformance 1 2.1 Optical Disk 1 2.2 Generating system .1 2.3 Receiving system .2 2.4 Compatibility statement .2 3 Normative references .2 4 Terms and definitions

9、 2 5 Conventions and notations 5 5.1 Representation of numbers .5 5.2 Names .5 6 Abbreviated terms 6 7 General description of the optical disk .6 8 General Requirements .7 8.1 Environments .7 8.1.1 Test environment7 8.1.2 Operating environment 8 8.1.3 Storage environment 8 8.1.4 Transportation 8 8.2

10、 Safety requirements .8 8.3 Flammability .8 8.4 Light fastness .8 9 Reference Drive 9 9.1 Optical system 9 9.2 Optical beam .9 9.3 Read channel 1 . 10 9.4 Disk clamping . 10 9.5 Rotation of the disk 11 9.6 Wobble channel (Read channel 2) . 11 9.7 Tracking channel (Read channel 2) . 11 9.8 Reference

11、servo systems . 11 9.8.1 Normalized servo transfer function . 11 9.8.2 Reference Servo for Axial Tracking . 12 9.8.3 Reference Servo for Radial Tracking . 13 10 Dimensional characteristics 14 10.1 Reference Planes 15 10.2 Overall dimensions 16 10.3 First transition area 16 10.4 Second transition are

12、a . 17 10.5 Clamping Zone . 17 10.6 Third transition area . 17 10.7 Information Zone 17 10.7.1 Sub-division of the Information Zone 18 10.7.2 Track mode . 19 10.8 Rim area 19 INCITS/ISO/IEC 25434:20082009 iv ISO/IEC 2008 All rights reserved 10.9 Remark on tolerances 19 11 Mechanical characteristics

13、19 11.1 Mass 19 11.2 Moment of inertia . 19 11.3 Dynamic imbalance 19 11.4 Axial runout 19 11.4.1 Tracking requirements at the Reference velocity (CLV) . 20 11.4.2 Tracking requirements at 3 000 RPM (CAV) 20 11.5 Radial runout 20 11.5.1 Tracking requirements at the Reference velocity (CLV) . 20 11.5

14、.2 Tracking requirements at 3 000 RPM (CAV) 21 12 Optical characteristics in the Information Zone . 21 12.1 Index of refraction 21 12.2 Thickness of the substrate 22 12.3 Reflectivity 22 12.4 Birefringence 22 12.5 Angular deviation . 22 13 Data format . 24 13.1 Data Frames . 24 13.1.1 Identification

15、 Data (ID) . 24 13.1.2 ID Error Detection Code (IED) 25 13.1.3 RSV . 26 13.1.4 Error Detection Code (EDC) . 26 13.2 Scrambled Frames . 26 13.3 ECC Blocks. 27 13.4 Recording Frames 28 13.5 Modulation and NRZI conversion 29 13.6 Physical Sectors 30 13.7 Layout of a Recording UNit (RUN) . 31 13.7.1 Rec

16、ording Unit position . 32 13.8 d.c. component suppression control 32 14 Track format . 33 14.1 Track shape 33 14.2 Track path . 34 14.3 Track pitch 34 14.4 Track layout 34 14.4.1 ADIP information 34 14.4.2 Physical format information in ADIP . 37 15 General description of the Information Zone 66 16

17、Layout of the Information Zone of a Single-session disk . 67 16.1 Usage of the Data Zone 68 16.1.1 Additional Testing Zone on Layer 1 (optional) 69 16.2 Physical Sector Numbers (PSNs) 70 17 Inner Drive Areas . 71 17.1 Initial Zone / Final Zone 71 17.2 Inner Disk Test Zones 72 17.3 Count Zone Run-in

18、/ Dummy Zone 72 17.4 Inner Disk Count Zones . 72 17.5 Inner Disk Administration Zone . 72 17.6 Table of Contents (TOC) Zone . 73 17.6.1 Table of Contents Blocks. 73 17.6.2 Recorded Area Indicators (optional) . 77 18 Lead-in Zone . 78 18.1 Guard Zone 1 79 18.2 Reserved Zone 1 79 18.3 Reserved Zone 2

19、79 INCITS/ISO/IEC 25434:20082009 ITIC 2009 All rights reserved v 18.4 Inner Disk Identification Zone 79 18.5 Reserved Zone 3 . 79 18.6 Reference Code Zone . 80 18.7 Buffer Zone 1 80 18.8 Control Data Zone 80 18.8.1 Physical format information. 80 18.8.2 Disk manufacturing information 83 18.8.3 Conte

20、nt provider information 83 18.9 Buffer Zone 2 83 19 Data Zone 83 20 Middle Zones 83 20.1 Buffer Zones 3 85 20.2 Reserved Zones 85 20.3 Guard Zones 2 85 21 Outer Drive Areas . 85 21.1 Outer Disk Administration Zones 85 21.2 Outer Disk Count Zones . 86 21.3 Dummy Zone / Count Zone Run-in 87 21.4 Outer

21、 Disk Test Zone 87 21.5 Guard Zones 3 87 22 Lead-out Zone. 87 22.1 Lead-out Zone at finalization . 87 22.2 Lead-out Zone at closing of first Session . 88 23 Multi-session Layout 89 23.1 Intro . 90 23.1.1 Buffer Zone A 90 23.1.2 Inner Session Identification Zone 90 23.1.3 Session Control Data Zone 90

22、 23.1.4 Buffer Zone B 90 23.2 Data Zone 90 23.3 Closure 90 23.3.1 Buffer Zone C 90 23.3.2 Outer Session Identification Zone . 90 24 Sequential recording in Fragments . 91 24.1 Opening a Session . 91 24.1.1 Incomplete Fragment . 91 24.1.2 Reserved Fragments 91 24.1.3 Recording User Data in Fragments

23、. 92 24.1.4 Closing a Fragment 92 24.2 Closing a Session. 93 24.2.1 Lead-in/Intro Zone 93 24.2.2 Closure Zone 94 24.3 Finalizing the disk 94 25 Assignment of Logical Sector Numbers (LSNs) . 94 26 Disk Control Blocks . 94 26.1 General format of Disk Control Blocks 94 26.2 Format of the Session DCB (S

24、DCB) 96 26.2.1 Session Items . 98 27 General 100 28 Method of testing 100 28.1 Environment . 100 28.2 Reference Drive 100 28.2.1 Optics and mechanics 100 28.2.2 Read power . 101 28.2.3 Read channels 101 INCITS/ISO/IEC 25434:20082009 vi ISO/IEC 2008 All rights reserved 28.2.4 Tracking 101 28.3 Defini

25、tion of signals . 101 29 Characteristics of the groove signals . 102 29.1 Phase depth 102 29.2 Push-pull signal . 102 29.3 Track Cross signal . 102 29.4 Normalized wobble signal 102 29.5 Characteristics of the wobble 103 30 Method of testing . 103 30.1 Environment . 103 30.2 Reference Drive 103 30.2

26、.1 Optics and mechanics . 103 30.2.2 Read power. 103 30.2.3 Read channels 104 30.2.4 Tracking 104 30.2.5 Scanning velocity . 104 30.3 Write conditions . 104 30.3.1 Write pulse waveform 104 30.3.2 Write power 105 30.3.3 Write power dependency on wavelength 105 30.3.4 Write power window . 106 30.3.5 W

27、rite power shift for layer L1 due to recording on layer L0 . 107 30.4 Measurement conditions . 107 31 Characteristics of the recorded signals 107 31.1 Channel bit length 107 31.2 Definition of signals . 107 31.2.1 High frequency signals (HF) 107 31.2.2 Modulated amplitude . 108 31.2.3 Signal asymmet

28、ry 108 31.2.4 Normalized Slicing Level jump 108 31.2.5 Jitter 109 31.2.6 Track Cross signal . 109 31.3 Read stability 109 32 Additional testing conditions 109 32.1 Test environment . 109 32.1.1 Optics . 109 32.2 Definition of signals . 110 32.2.1 Modulated amplitude . 110 32.2.2 Signal asymmetry 110

29、 32.2.3 Jitter 110 32.2.4 Track Cross signal . 110 32.2.5 Differential phase tracking error signal. 111 32.2.6 Tangential push-pull signal . 112 33 Quality of the recording layer 112 33.1 Defects 112 33.2 Data errors 112 34 Method of testing . 113 34.1 Environment . 113 34.2 Reference Drive 113 34.2

30、.1 Optics and mechanics . 113 34.2.2 Read power. 113 34.2.3 Read channels 113 34.2.4 Error correction 114 34.2.5 Tracking 114 35 Minimum quality of a Recording Unit 114 35.1 Tracking 114 INCITS/ISO/IEC 25434:20082009 ITIC 2009 All rights reserved vii 35.2 User-written data 114 Annex A (normative) 80

31、 mm +R DL disk 115 Annex B (normative) Structure for Extended format information in the Data Zone . 119 B.1 Extended format information . 119 B.1.1 EFI TOC . 119 Annex C (normative) Measurement of light reflectivity . 122 C.1 Calibration method . 122 C.2 Measuring method 123 Annex D (normative) Meas

32、urement of birefringence . 124 D.1 Principle of the measurement 124 D.2 Measurements conditions 125 D.3 Example of a measurement set-up 125 Annex E (normative) Measuring conditions for operation signals . 127 E.1 System diagram for jitter measurement and characterization of user data . 127 E.2 Open

33、loop transfer function for PLL 127 E.3 Slicer . 128 E.4 Conditions for measurement . 128 E.5 Measurement 129 Annex F (normative) Measurement of the differential phase tracking error . 130 F.1 Measuring method for the differential phase tracking error . 130 F.2 Measurement of t /T without time interv

34、al analyzer 130 F.3 Calibration of the circuit. 132 F.3.1 Saturation of comparators . 132 F.3.2 Correction for n and Vpc 132 Annex G (normative) The write pulse wave form for testing . 134 G.1 Pulsed write strategy 134 G.2 Castle write strategy. 136 G.3 Rise and fall times 138 Annex H (normative) 8-

35、to-16 Modulation 140 Annex I (normative) Optimum Power Control and Recording Conditions 148 I.1 Optimum writing power 148 I.1.1 Asymmetry and optimum writing power . 148 I.1.2 Measurement of asymmetry by means of 149 I.2 The OPC procedure 149 I.3 Write strategy parameters at other speeds . 150 I.4 M

36、edia margins at non-optimum write power . 150 Annex J (informative) Running OPC . 151 Annex K (informative) Wavelength dependency 152 K.1 Wavelength/Temperature behaviour of recorders 152 K.2 Write power / Wavelength dependency of the disk . 152 K.2.1 Measurement of the absorption of recording Layer

37、 0 / Layer 1 . 153 K.2.2 Measurement of the transmission of recording Layer 0 . 155 K.3 Determination of parameters for the Physical format information in ADIP . 155 INCITS/ISO/IEC 25434:20082009 viii ISO/IEC 2008 All rights reserved K.3.1 Determination of the start power for the OPC procedure in a

38、specific recorder . 156 Annex L (informative) Explanation about the usage of the reference servos 157 L.1 Approximation of servo behavior 157 L.1.1 Limitations of servo systems 157 L.2 Considerations for practical measurements and practical servo implementations . 158 L.2.1 Translation of characteri

39、stics to other speeds . 159 L.3 Example calculations for axial tracking 159 L.3.1 Basic requirements for all disks 159 L.3.2 Additional requirements for all disks able to be recorded at speeds above 2,4x . 160 L.3.3 Additional requirements for all disks able to be recorded at speeds above 8x 161 L.3

40、.4 Additional requirements for all disks able to be recorded at speeds above 12x 162 L.3.5 Stretching effect at highest rotational speed 163 L.4 Example calculations for radial tracking . 163 L.4.1 Basic requirements for all disks 163 L.4.2 Additional requirements for all disks able to be recorded a

41、t speeds above 2,4x . 164 L.4.3 Additional requirements for all disks able to be recorded at speeds above 8x 165 L.4.4 Additional requirements for all disks able to be recorded at speeds above 12x 166 Annex M (informative) Measurement of the groove wobble amplitude 167 M.1 Relation between normalize

42、d wobble signal and wobble amplitude . 167 M.2 Tolerances of the normalized wobble signal 167 Annex N (informative) Light fastness of the disk . 169 Annex O (informative) Transportation 170 O.1 General . 170 O.2 Packaging . 170 O.2.1 Temperature and humidity . 170 O.2.2 Impact loads and vibrations 1

43、70 Annex P (informative) Video Content Protection System 171 Annex Q (informative) How to use the Physical format information in ADIP . 172 Annex R (informative) Values to be Implemented in Existing and Future Specifications 174 Bibliography . 177 INCITS/ISO/IEC 25434:20082009 ITIC 2009 All rights r

44、eserved ix Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards thr

45、ough technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, als

46、o take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to pre

47、pare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility

48、that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 25434 was prepared by Ecma International (as ECMA-364) and was adopted, under a special “fast-track procedure”, by Joint Te

49、chnical Committee ISO/IEC JTC 1, Information technology, in parallel with its approval by national bodies of ISO and IEC. This third edition cancels and replaces the second edition (ISO/IEC 25434:2007), which has been technically revised. INCITS/ISO/IEC 25434:20082009 x ISO/IEC 2008 All rights reserved Introduction Ecma Technical Committee TC31 was established in 1984 for the standardization of Optical Disks and Optical Disk Cartridges (ODC). Since its establishment, the Committee has made major contributions to ISO/IEC toward t