ANSI American Society of Sanitary Engineering 1061-2015 Performance Requirements for Push-Fit Fittings.pdf

《ANSI American Society of Sanitary Engineering 1061-2015 Performance Requirements for Push-Fit Fittings.pdf》由会员分享，可在线阅读，更多相关《ANSI American Society of Sanitary Engineering 1061-2015 Performance Requirements for Push-Fit Fittings.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、Performance Requirements for Push-Fit Fittings ASSE InternationalASSE Standard #1061-2015ASSE Board Approved: May 2015ANSI Approved: June 2015An American National StandardPush-Fit Fittings iASSE Standard #1061-2015ASSE InternationalMokena, IllinoisCopyright 2015, 2011, 2006All rights reserved.Neithe

2、r this standard, nor any portion thereof, may be reproduced without the written consent of ASSE International.No product may be said to be listed by ASSE unless the manufacturer has applied to ASSE International, has had its product tested according to the applicable standards and, when the product

3、has passed the test, displays the ASSE Seal on the product.Instructions for receiving the authorization to display the seal are available from the ASSE International office. Organizations wishing to adopt or list any ASSE standard should print the ASSE standard number on the cover page first and in

4、equal or larger type to that of the adopting or listing organization.General Informationii Push-Fit Fittings ASSE Standard #1061-2015Push-Fit Fittings iiiASSE Standard #1061-2015This foreword shall not be considered a part of the standard. However, it is offered to provide background information.ASS

5、E standards are developed in the interest of consumer safety. This standard was developed to establish minimum performance requirements for push-fit fittings; an alternative method of connecting fittings with valves and tubing on potable water distribution systems and hydronic heat systems. There ar

6、e other applications for push-fit fittings, including compressed air systems and gas piping systems. However, the performance requirements and tests in ASSE Standard #1061 were developed for fittings installed in potable water distribution systems and hydronic heat systems only. Pressurized (compres

7、sed) air, which is used for laboratory testing, contains large amounts of stored energy that could present serious safety hazards should a system fail for any reason. It is the responsibility of the user of this standard to establish appropriate safety requirements prior to performing any of the tes

8、ts contained in this standard.Recognition is made of the time and support of those who participated in the development of this standard.This standard does not imply ASSEs endorsement of a product that conforms to these requirements.Compliance with this standard does not imply acceptance by any code

9、body.It is recommended that these devices be installed consistent with local codes.This standard was promulgated in accordance with procedures developed by ASSE International and approved by the American National Standards Institute (ANSI).Forewordiv Push-Fit Fittings ASSE Standard #1061-2015Edward

10、J. Lyczko, ChairpersonCleveland Clinic Retiree Cleveland, OHWilliam Briggs Jr.MGJ AssociatesNew York, NYTerry BurgerNSF InternationalYpsilanti, MIWilliam ChapinProfessional Code Consulting, LLCCullman, ALRon GeorgePlumb-Tech Design orb) A change in durometer greater than six (6) on the Shore A hardn

11、ess scale4.1.4.2 Sulfur-cured elastomeric materials are not compatible with copper alloys and are therefore not permitted.4.2 Adapter/Transition Fitting Connections4.2.1 Taper pipe threads, except dryseal, shall be in compliance with ANSI/ASME B1.20.1 or ASTM F1498.4.2.2 Dryseal threads shall be in

12、compliance with ANSI/ASME B1.20.3.Push-Fit Fittings 11ASSE Standard #1061-20154.2.3 CPVC solvent weld connections shall comply with ASTM D2846/D2846M or CSA B137.6.4.2.4 Cast copper alloy, wrought copper alloy and copper alloy solder joint connections shall comply with the dimensional requirements o

13、f ASME B16.18 or B16.22.4.2.5 Other types of connections shall comply with the applicable ANSI or CSA standards.4.3 Marking Instructions4.3.1 Marking of FittingsEach fitting shall have the following information marked on it where it will be visible after it has been installed:(a) Name of manufacture

14、r or trademark(b) When a fitting is not suitable for all four (4) materials, it shall be marked as follows for the materials for which they are suitable: Copper (Cu) CPVC PEX PE-RTWhen push-fit connectors are used on plumbing devices, the markings are permitted to be on the plumbing device.4.3.2 Fit

15、tings ” CTS or smaller are permitted to use a permanent label complying with the requirements of UL 969 or CSA C22.2 No. 0.15 to display the required markings.4.3.3 The markings shall be permanent.4.4 Installation InstructionsThe products installation instructions, packaging or specification sheets

16、shall include the following information:(a) Instruction to ensure that the tubing ends are cut square and are free of burrs on both the inside and outside of the tubing.(b) Instruction ensuring that there are no scratches, gouges or any form of damage on the circumference of the tubing within 1 inch

17、 (25.4 mm) of the cut end, as damage in this area may cause leakage.(c) Instruction ensuring that the tubing is pushed into the fitting fully and is engaged properly.(d) Whether or not the use of tube liners is required.(e) Any prohibitions for the products installation.(f) Maximum pressure-temperat

18、ure rating of the fitting.12 Push-Fit Fittings ASSE Standard #1061-2015Section V5.0 DefinitionsDefinitions not found in this section are located in the Plumbing Dictionary, Sixth Edition, published by ASSE International.Adapter FittingA fitting that has different types of connections on each outlet.

19、ConfigurationFitting configurations include, but are not limited to, straight connections, tees, elbows, 45 ells, end-stops and plugs.CTSAcronym for “Copper Tube Size.” The actual outside diameter is 1/8 inch larger than nominal tube size (i.e. ” CTS has an outside diameter of 0.625 inch).Push-Fit C

20、onnectorA push-fit connection (see definition of push-fit fitting) that is integral to a plumbing device.Push-Fit FittingA mechanical fitting that joins pipes or tubes and achieves a seal by pushing the mating pipe or tube into the fitting by hand.Note: The fitting can be removable or non-removable.

21、Transition FittingA fitting that connects different types of tubing.Tube LinerA cylindrical device having one flanged end that is inserted into the end of PEX tubing to accommodate the assembly within a fitting. Also referred to as a “tube stiffener.”ASSE International Chapter of IAPMO, LLC18927 Hickory Creek Drive, Suite 220 Mokena, Illinois 60448Phone: 708.995.3019 Fax: 708.479.6139 http:/www.asse-plumbing.org