AIR FORCE MIL-T-8606 C (2)-1979 TUBING STEEL CORROSION-RESISTANT (18-8 STABILIZED AND EXTRA LOW CARBON)《(18-8极低碳稳定)防腐钢制油管》.pdf

《AIR FORCE MIL-T-8606 C (2)-1979 TUBING STEEL CORROSION-RESISTANT (18-8 STABILIZED AND EXTRA LOW CARBON)《(18-8极低碳稳定)防腐钢制油管》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-T-8606 C (2)-1979 TUBING STEEL CORROSION-RESISTANT (18-8 STABILIZED AND EXTRA LOW CARBON)《(18-8极低碳稳定)防腐钢制油管》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-T-8606CLAMENDMSNT 212 July 1979SUPERSEDINGAMENDMENT 119 April 1974MILITARY SPECIFICATIONTuRING, STREL, CORROSION-RESISTANT(18-8 STABILIZED AND EXTW LOW CAREON)This amendment forms a part of Military SpecificationMIL-T-8606C, dated 18 June 1973, and is approved foruse by all Departments and Agenc

2、ies of the Department. of Defense.PAGE 22.1, under heading “Military Standards” add:I “MS33531 Tolerance, WeldedSceel TubingCorrosion-ResistantMS33533 Tolerance - Seamless Corrosion-ResistantSteel Tubing Round”Under heading ANADesign Standard” delete “Seamless” fromb the title of AND 10102.“PACE.3Ta

3、ble 1, check analysis tolerance“+0.20” and substitute “+0.20”.Check analysis tolerance“+0.15” and substituteTable 11, nominal wall“.041 through .050”.(percent) column, line 5: Delete(percent) cnlumn, line 6: Delete“+0.15”.PAGE 4thickness column, line 4: Delete and substituteAdd last line:“.051 and o

4、ver 10 percent of nnrmal wall thickness”.FSC 4710Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-KIL-C-8606CAmNm4Em 2uca,.4Page 2 “of 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IMIL-C-8606CAMEND

5、KENT 2bPAGE 63.10, lines 5, 6, 7 and 8, last two sentences: Delete and substitute:“Centerless grinding of the O.D. surface or grit blasting of outer andinner surfaces are not acceptable. When tubing is fabricated by welding,it shall be so processed as to eliminate the bead reinforcement or anydimens

6、ional indication whatever of che presence or location of the weld. ”add new paragraph to Section 3:“3.11 Tolerances /“3.11.1 Rnund tubing. Tolerances shall conform to MS 33531 orMS33533 aa applicable. ”I PAGE 8II 4.6.2, line 1: Delete “pieces” and substitute “piece”.PAGE 94.8,1, add.new sentence to

7、end of paragraph:“A slight discoloration of the cloth ofshall not be a cause for reject ion.”wfibrous materialPAGE 106.2, line (c): Delete “(see 3.8 and 3.9)” and substitute “(see 3.7and 3.8)”.Custodians:Army - MSNavy - ASI Air Force - 11Review Activities:Army - MI, MS, ARAir Force - 13, 19, 99DSA-CS User Activities:Army - ATNavy - OS, YDPreparing Activity:Air Force - 11Project No. 4710-0356Page 3 of 3uIProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-