AECMA PREN 7000-1-2002 (CANCELLED) Aerospace Series Non-Metallic Materials Rules for the Drafting and Presentation of Material Standards Part 1 General Rules Edition P 2 [Replaced .pdf

《AECMA PREN 7000-1-2002 (CANCELLED) Aerospace Series Non-Metallic Materials Rules for the Drafting and Presentation of Material Standards Part 1 General Rules Edition P 2 [Replaced .pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 7000-1-2002 (CANCELLED) Aerospace Series Non-Metallic Materials Rules for the Drafting and Presentation of Material Standards Part 1 General Rules Edition P 2 [Replaced .pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA STANDARD prEN 7000-1 NORME AECMA Edition P 2 AECMA NORM June 2002 PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTRIES - STANDARDIZATION k Gulledelle 94 - B-1200 Brussels -Tel. + 32 2 775 8110 - Fax. i 32 2 775 81 11 - www.aecma-stan.org Comments should be sent within six months after

2、 the date of publication to Gulledelle 94 AECMA-STAN 8-1200 BRUXELLES ICs: Descriptors: Material Domain ENGLISH VERSION Aerospace series Non-metallic materials Rules for the drafting and presentation of ma te rial standards Part 1 : General rules Supersedes edition P 1 September 1998 Srie arospatial

3、e Luft- und Raumfahrt Matriaux non-mtalliques Nichtmetallische Werkstoffe Rgles pour la rdaction et la prsentation des normes de matriaux Partie 1: Rgles gnrales Regeln fr die Erstellung und die Gestaltung von Werkstoffnormen Teil 1: Allgemeine Regeln This “Aerospace Series Prestandard has been draw

4、n up under the res European Association of Aerospace Industries - Standa needs of the European Aerospace Industry. It has b concerned Domain following member comments. After examinati agreement of AECMA-STAN it will be submitted as a ittee for Standardization) for formal vote. Replace page 1 of the

5、previous edition by this page - Nota - Extra copies can be supplied by B.N.A.E. - Technopolis 54 - 199. rue Jean-Jacaues Rousseau - 921 38 ISSY-LES-MOULINEAUX CEDEX Withdrawal approved 28 June 2002 STDOAECMA PREN 7000-L-ENGL 1998 m LOL23LL OOL5008 770 m Page 3 prEN 7000-1 : 1998 O Introduction This

6、standard is a level 2 document as defined in EN 4385. I Scope This standard specifies the general rules for the drafting and presentation of EN aerospace series non- metallic material standards. This standard is supported by EN 7000-2 onwards. 2 Normative references This European Standard incorporat

7、es by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European S

8、tandard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. IS0 31-0 IS0 31-1 IS0 31-3 IS0 31-4 IS0 31-9 IS0 31-1 1 IS0 1000 EN 4385 General principles concerning quantities, units and symbols Quantities and units o

9、f space and time Quantities and units of mechanics Quantities and units of heat Quantities and units of atomic and nuclear physics Mathematical signs and symbols for use in the physical sciences and technology SI units and recommendations for use in their multiples and of certain other units Aerospa

10、ce series - Non-metallic materials - General organisation of standardisation - Links between types of standards 1) 3 Definitions For the purposes of this standard, the following definitions apply: 3.1 Material standard A standard specifying a series of requirements relating to a non-metallic materia

11、l, which may be a semi- finished product, such as: - one or more delivery conditions; - one reference set of processing conditions for acceptance test and qualification purposes which may differ from the use condition intended by the user; - series of technical requirements for these different condi

12、tions. NOTE: A material standard may also specify one or more than one use condition, providing that the variants are not interconvertable. Such cases shall be clearly identified by the designation system given in the material standard. 1) Published as AECMA Prestandard at the date of publication of

13、 this standard Previous page is blank 3.2 Family of non-metallic material A group of non-metallic materials characterised by basic descriptions generally in semi-finished product forms such as but not exclusively: - rubbers; - sealants; - transparent plastics; - glass; - adhesives; - anaerobic polym

14、erizable compounds; - honeycombs; - paints; - reinforcement fibre; - preimpregnates; - textiles. 3.3 Semi-finished products A generic term used to indicate that the material as delivered is in an intermediate form to that occuring in the final component. This term may refer to the following: - adhes

15、ives where one delivered condition may be a two-part mix and the final use condition is the cured adhesive; - preimpregnates, which are subsequently shaped to produce a part with specified characteristics; - honeycomb which may be shaped and formed. 3.4 Type of semi-finished products Semi-finished p

16、roduct forms (sheets, rolls, tube, cloths, liquids, paste etc.) associated with the relevant family of non-metallic materials. 3.5 Final condition of use The condition of the material in which no further processing (except machining or shaping) is required before use. 3.6 Abbreviations Abbreviations

17、 shall be taken from IS0 31. The following are typical abbreviations used: - “a“ for thickness; - “b“ for width; - “I“ for length; - “Dl for outside diameter; - “d“ for inside diameter; - “0 for temperature; - “Y for time. NOTE 1: The abbreviation “min.“, for minimum shall not be used. When it is ne

18、cessary to state a minimum or maximum value this shall be done using the symbols I, , alternatively the word shall be written in full. The exception to this in when “min.“ and “max.“ are defined for other uses within abbreviations, e.g. Rmax. or Rmin NOTE 2: Values shall be preceded by a sign depend

19、ing on whether they are minimum or maximum values, (I, ); Symbols for sizes and units: see IS0 31-1, IS0 31-3, IS0 31-4, IS0 31-11 and IS0 1000. STD-AECMA PREN 7000-II-ENGL II778 LOL231L OOL5OLO b27 H Page 5 prEN 7000-1 : 1998 4 Rules for the drafting and presentation Standard sentences, placed in a

20、 frame, are listed below for the different clauses of the material standard and are mandatory. When necessary, information in the frame, indicated in italics, shall be completed or reworded. 4.1 Page 1: Title of the material standard The title shall give sufficient information to unambiguously ident

21、ify the finished or semi-finished product, in the delivery condition or use condition where applicable. Consequently: 1 The same title shall not be used for different material standards 2 Overlapping of material physical or mechanical characteristics for otherwise identical material standards shall

22、not normally be permitted. Each part of the title shall form one or several different lines: - Aerospace series; - the family of the non-metallic material; - form or forms, written in singular or plural, in conformity with the language used and, if appropriate, the method of production and/or final

23、use; - dimensions if appropriate; - relevant mechanical or physical limits if appropriate. 4.2 Page 2 Blank in principle: foreword or contents list if necessary. 4.3 Page 3, onwards 4.3.1 Clause O: Introduction When required this clause shall read: O Introduction This standard is a level 3 document

24、as defined in EN 4385. It has been prepared in accordance with (insert the relevant EN 7000 dash number). 4.3.2 Clause 1: Scope This clause shall read: 1 Scope This standard specifies the requirements relating to . (repeat all the information in the title in a grammatical sequence that satisfies the

25、 language used) . for aerospace applications. If necessary further information shall be added to clarify the field of application. STD-AECMA PREN 7000-II-ENGL 1998 M LOL2311 00150LL 565 Page 6 prEN 7000-1 : 1998 Subcase number - 1 2 3 4.3.3 Clause 2: References This clause shall read: Definitions Te

26、chnical specification Test method Frequency of testing Sample type 2 Refe re n ces 2.1 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publica

27、tions are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. I This subclau

28、se shall contain a list of documents, with their complete titles to which reference is made in the text and where applicable, the date of the reference. Bibliography I 2.2 This subclause contains a list of documents, with their complete titles, which have been used in the preparation of the text, an

29、d where applicable, the date of the reference. 4.3.4 Clause 3: ConventionslDefinitionslAbbreviations - Clause 3.1: Conventions This clause shall read: 3.1 Conventions For the purposes of this standard, the following conventions apply: 3.1.1 Subcase numbering In the column requirement at the left sid

30、e a subcase number is given. The definition of these subcase numbers is as follows: I- 4 1 Test piece definition I I 5 I Conditioning of test piece I I 6 I Testing condition I 7 Acceptance criteria The absence of a subcase indicates that the necessary information is given in Table 1 of this standard

31、, e.g. in the reference to the technical standard (characteristic number 1.004). STD-AECMA PREN 7000-%-ENGL 1998 10123LL OOL5OL2 4TL D Page 7 prEN 7000-1 : 1998 All the necessary information which does not appear is to be found in the referenced technical specification or the relevant test method. 3

32、.1.2 Batch acceptance testing identification In this material standard, batch acceptance test titles and subcases 7 acceptance criteria are highlighted in the form of bold frame and bold characters to show they are mandatory for routine release of the material. - Clause 3.2: Definitions If definitio

33、ns are required, this clause shall read: 3.2 Definitions For the purposes of this standard, the following definitions apply: Followed by a list of definitions. - Clause 3.3: Abbreviations If abbreviations are required, this clause shall read: 3.3 Abbreviations For the purposes of this standard, the

34、following abbreviations apply: Followed by a list of abbreviations. 4.3.5 Clause 4: Requirements This clause shall read: 4 Requirements The required characteristics are given in: Table 1 : General requirements Table 2: Requirements in the delivery condition Table 3: Requirements as processed to char

35、acteristic number 1 .O13 Table 4: Environmental testing requirements as processed to characteristic number 1 .O1 3. 4.4 Format of tables 4.4.1 This form is mandatory irrespective of the family of non-metallic material. The actual format is dependent on the family of non-metallic material. Table 1: s

36、ee annex A. This form describes the general characteristics of the product, and is applicable to all non-metallic material standards. STD-AECIA PREN 7000-L-ENGL 1994 LOL23LL OOL50L3 338 W Page 8 prEN 7000-1: 1998 4.4.2 This form shall be used for each of the following three tables for which it is re

37、quired to specify requirements. Tables 2 to 4: see annex B. When required optional characteristic selected from annex C shall be completed as follows: - table 2, requirements in the delivery condition (column 0 optional (see figure 1): add line or case number). table 3, requirements as processed to

38、characteristic number 1.013 (column 0 optional: add line or case number). table 4, environmental testing requirements as processed to characteristic number 1 .O13 (column 0 optional: add line or case number). - the characteristic numbers, (see annex C) shall be written in column 0 (see figure l), an

39、d shall be pre-fixed with the table number. When more than one characteristic number applies for a particular requirement, both characteristic numbers shall be shown in column 0. - the characteristic titles shall be written in column (see figure I), including any information to clarify the requireme

40、nts. - column (see figure 1) shall be completed with a subcase number corresponding to the information to be given in column (see figure 1) and selected from the following: 0 Characteristic number II 0 Characteristic I Subcase number Re uirements P Technical specification Test method Frequency of te

41、sting Sample type Test piece definition Conditioning of test piece Testing condition Acceptance criteria Figure 1 - a subcase shall be omitted, if the necessary information is given in the technical specification referenced in 1.004. - if all the necessary information is contained in the technical s

42、pecification, the subcase is opened by stating “see EN xxxx“. In this case a hyphen is inserted in the third column. No other subcase number will be given. STD-AECHA PREN 7000-1-ENGL 1998 LOL23LL OOL5OL4 274 Page 9 prEN 7000-1 : 1998 - - if the technical specification or the test method: - does not

43、give any information - only gives partial information - or gives a choice, or if the requirements differ from those given in the technical specification or test method, then subcases 1 to 7 shall be completed as required with the necessary information. - column 0 is completed, in accordance with the

44、 specific instructions given in the relevant dash numbered part of this standard. Values which will be agreed during qualification shall be expressed as a range in the material standard, e: No “X values to be specified in material standards. Supplied in final condition of use It is only necessary to

45、 complete those subcases for which information is required to be specified. 4.5 General instructions for completion of the tables 4.5.1 General The column 0 (see figure 1) is optional. If used, the case number shall be consecutive. Alternatively, it can be replaced by a consecutive line numbering as

46、 indicated in the dash number part. If there is insufficient width in a column then the information shall be repeated below and marked “continued“. See examples in EN 7000-2 onwards. 4.5.3 Tables 2 to 4 This form shall be filled in accordance with the relevant part of this standard (see EN 7000-2 on

47、wards). If all the characteristics covered by that particular table are not required, keep the table heading and write: - I NO requirements I If the characteristics covered by table 2 are the same as table 3 (.e. delivery condition is final condition of use) then keep the table 2 heading and write:

48、- I No requirements: see table 3. I NOTE: Test requirements shown in the technical specification are only mandatory when referenced in the material standards. STD-AECMA PREN 7000-1-ENGL 1998 m 1012311 0015015 100 m Page 10 prEN 7000-1 : 1998 Where one or more of the test requirements defined as foll

49、ows: - test method: - frequency of testing; - sample type; - test piece definition; - condition of test piece; - testing condition; - acceptance criteria are not specified or differ from the requirements of the technical specification or test method, they shall be included by means of one or more subcase numbers in accordance with the instructions given in 4.4.2. 4.6 Batch release testing In the material standards, batch release test titles and subcase 7 acceptance criteria shall be in a bold frame with bold characters to show they are manda