AECMA PREN 6131-2006 Aerospace series Composite clip nut self-locking Edition P 3《航空航天系列.混合物架子自动锁螺母 P3版》.pdf
《AECMA PREN 6131-2006 Aerospace series Composite clip nut self-locking Edition P 3《航空航天系列.混合物架子自动锁螺母 P3版》.pdf》由会员分享,可在线阅读,更多相关《AECMA PREN 6131-2006 Aerospace series Composite clip nut self-locking Edition P 3《航空航天系列.混合物架子自动锁螺母 P3版》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、ASD STANDARD NORME ASD ASD NORM prEN 6131 Edition P 2 February 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: See foreword for superseded version Descr
2、iptors: ENGLISH VERSION Aerospace series Composite clip nut, self-locking Srie arospatiale crou pincer en composite, freinage interne Luft- und Raumfahrt Clipmutter aus Verbundwerkstoff, selbstsichernd This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (AeroSp
3、ace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this pre-standard, the technical
4、content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Comm
5、ittee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approve
6、d for publication 28 February 2006 Comments should be sent within six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo repr
7、oduction or networking permitted without license from IHS-,-,-prEN 6131:20062 Foreword Due to a communication problem between the sponsor/responsible project team and ASD-STAN there was a confusion regarding the edition numbering of the recent version of this standard. In order to solve the situatio
8、n the ASD-STAN Board agreed to publish this version as Edition P2 and it is superseding the P1 version of prEN 6131. Contents Page 1 Scope 3 2 Normative references 3 3 Requirements.3 3.1 Configuration, dimensions, tolerances and mass .3 3.2 Material .4 3.3 Nut surface treatment4 3.4 Temperature rang
9、e 4 4 Designation 8 5 Marking .9 6 Technical specification .9 7 Required installation dimensions 9 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prE
10、N 6131:20063 1 Scope This standard specifies the configuration, dimensions, tolerances and mass of composite clip nuts for structural applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition
11、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. AMS 2700, Passivation of corrosion resistant steels. 1)AMS 5085, Steel sheet, strip and plate 0.47 - 0.55C (SAE 1050) ann
12、ealed. 1)AMS 5525, Steel, corrosion and heat resistant, sheet, strip and plate - 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1 800 F (982 C ) Solution heat treated. 1)AMS-QQ-P-416, Plating, cadmium (electrodeposited).1)AS 5272, Lubricant, solid film, heat cured, corrosion inhibiting procurement s
13、pecification. 1)AS 8879, Screw threads Controlled radius root, with increase minor diameter general specification. 1)ASTM D5204, Standard classification system for polyamide-imide (PAI) molding and extrusion materials. 2)NASM 25027, Nut, self-locking, 250 F, 450 F and 800 F. 3)3 Requirements 3.1 Con
14、figuration, dimensions, tolerances and mass The configuration, dimensions, tolerances and mass shall conform to Figures 1, 2 and 3 and Tables 1 and 2. Dimensions and tolerances are expressed in millimetres (inches). 1) Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive
15、, Warrendale, PA 15096-0001, USA.2) Published by: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA, 19428-2959 USA. 3) Published by: Aerospace Industries Association of America. Inc. (AIA), 1250 Eye Street, N.W., Washington D.C. 20005-3924,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AECMAPREN61312006AEROSPACESERIESCOMPOSITECLIPNUTSELFLOCKINGEDITIONP3 航空航天 系列 混合物 架子 自动 螺母 P3 PDF

链接地址:http://www.mydoc123.com/p-421732.html