BS PD ISO IEC TS 24748-6-2016 Systems and software engineering Life cycle management System integration engineering《系统和软件工程 生命周期管理 系统集成工程》.pdf

《BS PD ISO IEC TS 24748-6-2016 Systems and software engineering Life cycle management System integration engineering《系统和软件工程 生命周期管理 系统集成工程》.pdf》由会员分享，可在线阅读，更多相关《BS PD ISO IEC TS 24748-6-2016 Systems and software engineering Life cycle management System integration engineering《系统和软件工程 生命周期管理 系统集成工程》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、Systems and software engineering Life cycle management Part 6: System integration engineering PD ISO/IEC TS 24748-6:2016 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National foreword This Published Document is the UK implementation of ISO/IEC TS 24748- 6:2016. T

2、he UK participation in its preparation was entrusted to Technical Committee IST/15, Software and systems engineering. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a cont

3、ract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 88220 3 ICS 35.080 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the

4、 authority of the Standards Policy and Strategy Committee on 31 December 2016. Amendments/corrigenda issued since publication Date Text affected PUBLISHED DOCUMENT PD ISO/IEC TS 24748-6:2016Systems and software engineering Life cycle management Part 6: System integration engineering Ingnierie des sy

5、stmes et du logiciel Gestion du cycle de vie Partie 6: Ingnierie de lintgration du systme ISO/IEC TS 24748-6 First edition 2016-12-01 Reference number ISO/IEC TS 24748-6:2016(E) TECHNICAL SPECIFICATION ISO/IEC 2016 PD ISO/IEC TS 24748-6:2016 ii ISO/IEC 2016 All rights reserved COPYRIGHT PROTECTED DO

6、CUMENT ISO/IEC 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior w

7、ritten permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO/IE

8、C TS 24748-6:2016(E) PD ISO/IEC TS 24748-6:2016 ISO/IEC TS 24748-6:2016(E)Foreword v Introduction vi 1 Scope . 1 2 Normative references 1 3 T erms, definitions and abbr e viat ed t erms 2 3.1 Terms and definitions . 2 3.2 Abbreviatied terms 4 4 Conformance . 4 4.1 Intended usage 4 4.2 Conformance to

9、 processes 4 4.3 Conformance to information item content . 4 4.4 Full conformance. 5 4.5 Tailored conformance . 5 4.5.1 Processes 5 4.5.2 Information items . 5 5 Concepts and principles 5 5.1 General . 5 5.2 Integration fundamentals 5 5.2.1 Terms and approaches 5 5.2.2 Notions of aggregate and of in

10、terface 7 5.2.3 Integration based on architecture and design . 8 5.2.4 Integration by layers of systems . 9 5.2.5 Environmental context 10 5.2.6 Integration strategy 11 5.2.7 Verification principles related to integration engineering .17 5.2.8 Validation principles related to integration engineering

11、 .18 5.2.9 Efficiency of the integration strategy 18 5.3 Practical considerations .19 5.3.1 Iteration and recursion of processes .19 5.3.2 Integration Enabling System 19 6 Processes .22 6.1 Integration engineering activities .22 6.2 Integration Process 22 6.2.1 Purpose .22 6.2.2 Outcomes .23 6.2.3 A

12、ctivities and tasks .24 6.3 Other technical processes related to integration engineering 28 6.3.1 Business or mission analysis process .28 6.3.2 Stakeholder needs and requirements definition process 28 6.3.3 System requirements definition process .28 6.3.4 Architecture definition process .29 6.3.5 D

13、esign definition process 29 6.3.6 System analysis process30 6.3.7 Verification process 30 6.3.8 Validation process 30 6.4 Integration management .30 6.4.1 Management overview 30 6.4.2 Composition of integration teams and skills 30 6.4.3 Integration planning, assessment and control 31 6.4.4 Relations

14、hip to Project assessment and control .31 6.4.5 Relationship to Configuration management .31 6.4.6 Relationship to Agreement processes 32 ISO/IEC 2016 All rights reserved iii Contents Page PD ISO/IEC TS 24748-6:2016 ISO/IEC TS 24748-6:2016(E)7 Information items outlines .32 7.1 Integration Plan .32

15、7.2 System Integration Aggregate Definition Information 33 7.3 System Integration Procedure and Report 33 Bibliogr aph y .35 iv ISO/IEC 2016 All rights reserved PD ISO/IEC TS 24748-6:2016 ISO/IEC TS 24748-6:2016(E) Foreword ISO (the International Organization for Standardization) and IEC (the Intern

16、ational Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fie

17、lds of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a

18、joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of document should be noted. This docume

19、nt was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or

20、 all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users

21、 and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementar

22、y information The committee responsible for this document is ISO/IEC JTC 1, Information technology, Subcommittee SC 7, Systems and software engineering. A list of all parts of the ISO/IEC 24748 series can be found on the ISO website. ISO/IEC 2016 All rights reserved v PD ISO/IEC TS 24748-6:2016 ISO/

23、IEC TS 24748-6:2016(E) Introduction This document was developed in response to a need for consistent terminology, definitions and guidance that elaborates the area of system integration, taking into account the context of use and the proven practices for the development of systems. ISO/IEC/IEEE 1528

24、8 includes an integration process that focuses on physically assembling the implemented system elements composing a system to obtain an “integrated system”. This process interfaces directly to other technical processes and indirectly to activities and tasks of other technical processes, in particula

25、r, the processes that define the system requirements, architecture and design. The purpose of this document is to facilitate the usage of the integration process of the latest revision of ISO/IEC/IEEE 15288 by providing guidance on system integration. This document describes the integration engineer

26、ing activities dealing with planning, performing and managing the integration of a system, including the related activities of other technical processes, in particular, verification and validation processes. These are real practices in industry, i.e. the integration of a system is technically engine

27、ered and managed as a project (included in the system development project). Although these practices are performed, they were not formalized in a standard or a guide when this document was written.vi ISO/IEC 2016 All rights reserved PD ISO/IEC TS 24748-6:2016 Systems and software engineering Life cy

28、cle management Part 6: System integration engineering 1 Scope This document specifies activities and processes to be implemented for engineering the integration of systems-of- interest throughout the life cycle (systems made of products and/or services; see Note 1), provides guidance for the integra

29、tion process and its relationships to other system life cycle processes as described in ISO/IEC/IEEE 15288, specifies the information items to be produced through the implementation of the integration engineering (integration process and its relationships to other system life cycle processes), speci

30、fies the contents of the information items, and provides guidelines for the format of the information items. This document can be applied to those who use or plan to use ISO/IEC/IEEE 15288 on projects dealing with man-made systems, software-intensive systems, products and services related to those s

31、ystems, regardless of project scope, methodology, size or complexity, and anyone performing integration engineering activities to aid in ensuring that the application of the integration process and its relationships to other system life cycle processes conform to ISO/IEC/ IEEE 15288. NOTE 1 Systems

32、concerned within this document are those as defined in ISO/IEC/IEEE 15288, i.e. systems that are man-made and can be configured with one or more of the following: hardware, software, data, humans, processes (e.g. processes for providing service to users), procedures (e.g. operator instructions), fac

33、ilities, materials and naturally occurring entities. NOTE 2 This document is intended to be consistent with the other parts of ISO/IEC 24748. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this do

34、cument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC/IEEE 15288:2015, Systems and software engineering System life cycle processes TECHNICAL SPECIFICATION ISO/IEC TS 24748-6:201

35、6(E) ISO/IEC 2016 All rights reserved 1 PD ISO/IEC TS 24748-6:2016 ISO/IEC TS 24748-6:2016(E) 3 T erms, d efinitions and abbr e viat ed t erms 3.1 T erms and definiti ons For the purposes of this document, the terms and definitions given in ISO/IEC/IEEE 15288 and the following apply. ISO and IEC mai

36、ntain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/ /www.electropedia.org/ ISO Online browsing platform: available at https:/ /www.iso.org/obp/ 3.1.1 acquirer stakeholder that acquires or procures a product or service from a sup

37、plier (3.1.9) SOURCE: ISO/IEC/IEEE 15288:2015, 4.1.1 3.1.2 aggregate composition of several implemented system elements (3.1.11) that are assembled (3.1.3), on which a set of verification actions (3.1.17) and/or validation actions (3.1.15) is applied 3.1.3 a s s emble activities for combining and co

38、nnecting implemented system elements (3.1.11) or aggregates (3.1.2) to support specific goals, i.e. integration (3.1.5), verification (3.1.16), validation (3.1.14), manufacturing and production. 3.1.4 e na b ling s ys te m system (3.1.10) that supports a system-of-interest (3.1.12) during its life c

39、ycle stages, but does not necessarily contribute directly to its function during operation EXAMPLE When a system-of-interest enters the production stage, a production enabling system is required. Note 1 to entry: Each enabling system has a life cycle of its own. ISO/IEC/IEEE 15288 is applicable to e

40、ach enabling system when, in its own right, it is treated as a system-of-interest. SOURCE: ISO/IEC/IEEE 15288:2015, 4.1.18 3.1.5 integration activities of combining several implemented system elements (3.1.11) and activating the interfaces (3.1.8) to form a realized system (product or service) that

41、enables interoperation between the system elements and with other systems (3.1.10) to satisfy system requirements, architecture characteristics and design properties Note 1 to entry: In this document, the term “integration” is limited to the integration of the implemented system elements which compo

42、se a system and the necessary life cycle related activities. Integration may occur to connect a system-of-interest (3.1.12) with external interoperating systems and/or enabling systems (3.1.4). Note 2 to entry: The process of combining software components, hardware components or both into an overall

43、 system (ISO/IEC/IEEE 24765).2 ISO/IEC 2016 All rights reserved PD ISO/IEC TS 24748-6:2016 ISO/IEC TS 24748-6:2016(E) 3.1.6 integration engineering set of activities that defines, analyzes and executes integration (3.1.5) across the life cycle, including interactions with other life cycle processes

44、Note 1 to entry: The application of the system life cycle processes and knowledge of the system-of-interest (3.1.12) are necessary in order to integrate a set of system elements (3.1.11) into a system (3.1.10). 3.1.7 integration management set of activities that plans, assesses and controls the inte

45、gration activities and all related activities Note 1 to entry: It helps ensure that the process outcomes are achieved and that the integration related information items are identified, documented, maintained, communicated and traced throughout the life cycle of the concerned system (3.1.10). 3.1.8 i

46、nterface set of logical and/or physical characteristics required to exist at a common boundary or connection between system elements (3.1.11) Note 1 to entry: As examples of interface definition, refer to ISO/IEC/IEEE 24765. 3.1.9 supplier organization or individual that enters into an agreement wit

47、h the acquirer (3.1.1) for the supply of a product or service SOURCE: ISO/IEC/IEEE 15288:2015, 4.1.45 3.1.10 system combination of interacting elements organized to achieve one or more stated purposes Note 1 to entry: A system may be considered as a product or as the services it provides. SOURCE: IS

48、O/IEC/IEEE 15288:2015, 4.1.46 3.1.11 system element member of a set of elements that constitute a system (3.1.10) SOURCE: ISO/IEC/IEEE 15288:2015, 4.1.47 3.1.12 system-of-interest system (3.1.10) whose life cycle is under consideration in the context of this document SOURCE: ISO/IEC/IEEE 15288:2015,

49、 4.1.48 3.1.13 user individual or a group that benefits from a system (3.1.10) during its utilization SOURCE: ISO/IEC/IEEE 15288:2015, 4.1.52, modified 3.1.14 validation confirmation, through the provision of objective evidence, that the requirements for a specific intended use or application have been fulfilled Note 1 to entry: A system (3.1.10) is able to accomplish its intended use, goals and objectives (i.e. meet stakeholder requirements) in the intended operational environment. The right syste