BS PD CEN TS 1852-2-2015 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) Guidance for the assessment of conformity《地下非承压排水和排污.pdf

《BS PD CEN TS 1852-2-2015 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) Guidance for the assessment of conformity《地下非承压排水和排污.pdf》由会员分享，可在线阅读，更多相关《BS PD CEN TS 1852-2-2015 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) Guidance for the assessment of conformity《地下非承压排水和排污.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication PD CEN/TS 1852-2:2015 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) Part 2: Guidance for the assessment of conformityPD CEN/TS 1852-2:2015 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation o

2、f CEN/ TS 1852-2:2015. It supersedes DD CEN/TS 1852-2:2009 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for non-pressure applications. A list of organizations represented on this committee can be obtained on request to its

3、 secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 90348 9 ICS 23.040.01; 93.030 Compliance with a Briti

4、sh Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 December 2015. Amendments issued since publication Date Text affectedPD CEN/TS 1852-2:2015TECHNICAL SPECIFICATION SPCIFICATION TEC

5、HNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 1852-2 December 2015 ICS 93.030; 23.040.01 Supersedes CEN/TS 1852-2:2009 English Version Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity Systmes de canalisations

6、 en plastiques pour les branchements et les collecteurs dassainissement sans pression enterrs - Polypropylne (PP) - Partie 2: Guide dvaluation de la conformit Kunststoff-Rohrleitungssysteme fr erdverlegte drucklose Abwasserkanle und -leitungen - Polypropylen (PP) - Teil 2: Empfehlungen fr die Beurte

7、ilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 13 November 2015 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on th

8、e question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national s

9、tandards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic

10、of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISAT

11、ION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 1852-2:2015 EPD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 2 Contents Page

12、European foreword . 3 Introduction 4 1 Scope 6 2 Normative references 6 3 Terms and definitions . 6 4 Abbreviated terms . 10 5 General . 10 6 Testing and inspection . 10 6.1 Material specification . 10 6.2 Grouping 10 6.2.1 General . 10 6.2.2 Size groups 10 6.2.3 Fitting groups 11 6.3 Type testing (

13、TT) 11 6.4 Batch release tests . 15 6.5 Process verification tests 16 6.6 Audit tests . 18 6.7 Indirect tests 19 6.8 Test records . 20 Annex A (informative) Basic test matrix . 21 Bibliography . 22 PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 3 European foreword This document (CEN/TS 1852-2:2015) ha

14、s been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. This document supersedes CEN/TS 1852-2:2009. The main change compared to the previous version concerns the compliance with the latest version of the template for

15、assessment of conformity. EN 1852 consists of the following parts, under the general title Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP) Part 1: Specifications for pipes, fittings and the system Part 2: Guidance for the assessment of conformity (the pr

16、esent TS) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards or

17、ganisations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe

18、mbourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 4 Introduction Figures 1 and 2 are intended to provide general information on the concept of testing and organisa

19、tion of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this document details the applicable characteristics to be assessed as well as the frequency and sa

20、mpling of testing. A typical scheme for the assessment of conformity of materials, pipes, fittings, joints or assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment of conformity of materials, p

21、ipes, fittings, joints or assemblies by manufacturers, including certification, is given in Figure 2. PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 5 Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including certification PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 6 1 Sc

22、ope This Technical Specification gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1852 intended to be included in the manufacturers quality plan as part of the quality management system and for the establish

23、ment of certification procedures. NOTE In order to help the reader, a basic test matrix is given in Annex A. In conjunction with EN 1852-1 this document is applicable to solid wall piping systems made of polypropylene (PP) intended to be used for: non-pressure underground drainage and sewerage outsi

24、de the building structure (application area code “U“), and non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D“) and outside the building structure. This is reflected in the marking of products by “U“ and “UD“. 2 Normative

25、references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

26、es. EN 1852-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system 3 Terms and definitions For the purposes of this document, the following terms and definitions given in EN 1852-1 and the fo

27、llowing apply. 3.1 certification body impartial body, governmental or non-governmental, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certification body is preferably compliant w

28、ith EN ISO/IEC 17021-1 1. 3.2 inspection body body, that performs inspection Note 1 to entry: A body can be an organization or part of an organization. Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 2. PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 7 3.3 testing labo

29、ratory laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products Note 1 to entry: In the context of this part of EN 1852, the materials and products can be subjected to type testing, batch release testing, process verificati

30、on testing, audit testing, and witness testing, as applicable. Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 3 . 3.4 quality management system management system to direct and control an organization with regard to quality Note 1 to entry: Requirements for qualit

31、y management systems are given in EN ISO 9001 4 . 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing performed to prove that the material, product, joint or assem

32、bly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are done regularly. 3.7 batch release test BRT test performe

33、d by or on behalf of the manufacturer on a batch of materials or products, which has to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer on materials, products or joints at specific intervals to confirm

34、that the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of materials or products and are carried out as a measure of process control. 3.9 audit test AT test perform

35、ed by a test laboratory on behalf of an inspection body or certification body to confirm that the material, product, joint or assembly continues to conform to the requirements given in the relevant standard and to provide information to assess the effectiveness of the quality management system PD CE

36、N/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 8 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characteristic, having previously verified its correlation with the specified test 3.11 witness test WT test accepted by an inspe

37、ction or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or certification body, qualified in testing 3.12 material generic term for compositions of compounds/formulations grouped

38、 by families, expressed by generic names, e.g. polypropylene, stainless steel, brass or EPDM Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and Industry, Sub- group on Product Testing Procedures (EC, DG ENT and IND, SG PTP). 3.13 compound/formulation clearly

39、 defined homogenous mixture of base polymer with additives, i.e. antioxidants, pigments, stabilizers and others, at a dosage level necessary for the processing and the intended use of the final product 3.14 material batch clearly identified quantity of a given homogeneous compound/formulation manufa

40、ctured under uniform conditions and defined and identified by the compound/formulation manufacturer 3.15 product pipe, fitting, or valve of a clearly identified type intended to be a part of a piping system which the manufacturer puts on the market 3.16 product batch clearly identified collection of

41、 products, manufactured consecutively or continuously under the same conditions, using the same compound/formulation conforming to the same specification Note 1 to entry: The production batch is defined and identified by the product manufacturer. 3.17 lot clearly identifiable sub-division of a batch

42、 for inspection purposes 3.18 sample one or more products drawn from the same production batch or lot, selected at random without regard to their quality Note 1 to entry: The number of products in the sample is the sample size. PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 9 3.19 group collection of

43、similar products from which samples are selected for testing purposes 3.20 component product manufactured out of a specific composition compound/formulation, brought to the market as part of another product or as a spare part 3.21 joint connection between two products 3.22 assembled product assemble

44、d final product using two or more single parts 3.23 thermoplastics fabricated fitting fitting produced from pipe and/or from injection-moulded fittings by thermoforming, solvent- cementing or welding 3.24 assembly product that can be dismantled into a set of components EXAMPLE A test piece consistin

45、g of various products. 3.25 sampling plan specification of the type of sampling to be used combined with the operational specification of the entities or increments to be taken, the samples to be constituted and the measurements or tests to be made EXAMPLE A specific plan which indicates the number

46、of units of products or assemblies to be inspected. 3.26 product type generic description of a product EXAMPLE A pipe or fitting or valve or their main parts, of the same design, from a particular compound. 3.27 cavity (moulding) space within a mould to be filled to form the moulded product EXAMPLE

47、That part of an injection mould which gives the form to the injection-moulded product. PD CEN/TS 1852-2:2015 CEN/TS 1852-2:2015 (E) 10 4 Abbreviated terms To avoid misunderstanding, the abbreviations in this clause are defined as being the same in each language. For the same reason, the terms are gi

48、ven in the three languages, English, French and German. EN FR DE AT audit test essai daudit berwachungsprfung BRT batch release test essai de libration de campagne de fabrication Freigabeprfung einer Charge IT indirect test essai indirect indirekte Prfung PVT process verification test essai de vrifi

49、cation du procd de fabrication Prozessberprfung TT type test essai de type Typprfung WT witness testing essai tmoin Prfung unter Aufsicht 5 General Materials, products, joints and assemblies shall conform to the requirements given in EN 1852-1. Products and assemblies shall be produced by the manufacturer under a quality management system which includes a quality plan. NOTE It is advised that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 4. 6 Testing and inspection 6