ASTM B366B366M-17 Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings.pdf

《ASTM B366B366M-17 Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings.pdf》由会员分享，可在线阅读，更多相关《ASTM B366B366M-17 Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B366/B366M 17Standard Specification forFactory-Made Wrought Nickel and Nickel Alloy Fittings1This standard is issued under the fixed designation B366/B366M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of l

2、ast revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers wrought welding fittings forpressure piping, factory-made from nickel and nickel alloys.Thre

3、aded fittings as covered in ASME B16.11 are also coveredby this specification. The term welding applies to butt-weldingor socket-welding parts such as 45 and 90 elbows, 180 bends,caps, tees, reducers, lap-joint stub ends, and other types, ascovered by ASME B16.9, ASME B16.11, MSS SP-43, MSSSP-95, an

4、d MSS SP-97.1.1.1 Several grades of nickel and nickel alloys are includedin this specification. Grades are designated with a prefix, WPorCR, based on the applicable ASME or MSS dimensional andrating standards.1.1.2 Class WP fittings are those manufactured to therequirements of ASME B16.9, B16.11.1.1

5、.3 For each of the WP nickel and nickel alloy grades,several classes of fittings are covered to indicate whetherseamless or welded construction was utilized. Class designa-tions are also utilized to indicate the nondestructive test methodand extent of nondestructive examination (NDE). Table 1 isgene

6、ral summary of the fitting classes applicable to all WPgrades of nickel and nickel alloys covered by this specification.There are no classes for the CR grades. Specific requirementsare covered elsewhere.1.2 This specification does not apply to cast welding fit-tings.1.3 Optional supplementary requir

7、ements are provided forfittings where a greater degree of examination is desired. Thesesupplementary requirements call for additional tests. Whendesired, one or more of these may be specified in the order.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as st

8、andard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.5 This standard does not purport to address all of thesafety concerns, if any, a

9、ssociated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateSafety Data Sheet (SDS) for this product/material as providedby the manufacturer, to establish appropriate safety and healthpractices, and dete

10、rmine the applicability of regulatory limi-tations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendat

11、ions issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2B127 Specification for Nickel-Copper Alloy (UNS N04400)Plate, Sheet, and StripB160 Specification for Nickel Rod and BarB161 Specification for Nickel Seamless Pipe and Tub

12、eB162 Specification for Nickel Plate, Sheet, and StripB163 Specification for Seamless Nickel and Nickel AlloyCondenser and Heat-Exchanger TubesB164 Specification for Nickel-Copper Alloy Rod, Bar, andWireB165 Specification for Nickel-Copper Alloy (UNS N04400)Seamless Pipe and TubeB166 Specification f

13、or Nickel-Chromium-Iron Alloys (UNSN06600, N06601, N06603, N06690, N06693, N06025,N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Rod, Bar, andWireB167 Specification for Nickel-Chromium-Iron Alloys (UNSN06600, N06601, N0

14、6603, N06690, N06693, N06025,N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Seamless Pipeand Tube1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct respo

15、nsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved June 1, 2017. Published June 2017. Originallyapproved in 1961. Last previous edition approved in 2016 as B366/B366M 16.DOI: 10.1520/B0366_B366M-17.2For referenced ASTM standards, visit the ASTM web

16、site, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor

17、Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations

18、 issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1B168 Specification for Nickel-Chromium-Iron Alloys (UNSN06600, N06601, N06603, N06690, N06693, N06025,N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Allo

19、y (UNS N06674) Plate, Sheet,and StripB333 Specification for Nickel-Molybdenum Alloy Plate,Sheet, and StripB335 Specification for Nickel-Molybdenum Alloy RodB407 Specification for Nickel-Iron-Chromium Alloy Seam-less Pipe and TubeB408 Specification for Nickel-Iron-Chromium Alloy Rodand BarB409 Specif

20、ication for Nickel-Iron-Chromium Alloy Plate,Sheet, and StripB423 Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825, N08221, andN06845) Seamless Pipe and TubeB424 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNSN08825, UNS N08221, and UNS N06845) Plate, Sheet,and StripB425 Specif

21、ication for Ni-Fe-Cr-Mo-Cu Alloy (UNSN08825, UNS N08221, and UNS N06845) Rod and BarB434 Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, UNS N10242) Plate, Sheet,and StripB435 Specification for UNS N06002, UNS N06230, UNSN12160, and UNS R30556 Plate, Sheet, and StripB443 Specif

22、ication for Nickel-Chromium-Molybdenum-Columbium Alloy(UNS N06625) and Nickel-Chromium-Molybdenum-SiliconAlloy (UNS N06219) Plate, Sheet,and StripB444 Specification for Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625 and UNS N06852) andNickel-Chromium-Molybdenum-Silicon Alloy (UNSN06219) Pip

23、e and TubeB446 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-Chromium-Molybdenum-Tungsten Alloy (UNS N06650)Rod and BarB462 Specification for Forged or Rolled UNS N06030, UNSN06022, UNS N06035, UNS N06200,

24、 UNS N06059,UNS N10362, UNS N06686, UNS N08020, UNSN08367, UNS N10276, UNS N10665, UNS N10675,UNS N10629, UNS N08031, UNS N06045, UNSN06025, UNS R20033 Alloy Pipe Flanges, Forged Fit-tingsB463 Specification for UNS N08020 Alloy Plate, Sheet, andStripB464/B464M Specification for Welded UNS N08020 All

25、oyPipeB468 Specification for Welded UNS N08020 Alloy TubesB472 Specification for Nickel Alloy Billets and Bars forReforgingB473 Specification for UNS N08020, UNS N08024, andUNS N08026 Nickel Alloy Bar and WireB511 Specification for Nickel-Iron-Chromium-Silicon AlloyBars and ShapesB512 Specification

26、for Nickel-Chromium-Silicon Alloy(UNS N08330) Billets and BarsB514 Specification for Welded Nickel-Iron-ChromiumAlloyPipeB515 Specification for Welded UNS N08120, UNS N08800,UNS N08810, and UNS N08811 Alloy TubesB516 Specification for Welded Nickel-Chromium-IronAlloy(UNS N06600, UNS N06601, UNS N066

27、03, UNSN06025, UNS N06045, UNS N06690, and UNS N06693)TubesB517 Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, andUNS N06045) PipeB535 Specification for Nickel-Iron-Chromium-Silicon Al-loys (UNS N08330 and N08332) Seamless Pipe and TubeB536 Specification for

28、 Nickel-Iron-Chromium-Silicon Al-loys (UNS N08330 and N08332) Plate, Sheet, and StripB564 Specification for Nickel Alloy ForgingsB572 Specification for UNS N06002, UNS N06230, UNSN12160, and UNS R30556 RodB573 Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003, N10242) RodB574 Spec

29、ification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy RodB575 Specification for Low-Carbon Nickel-Chromium-Moly

30、bdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten, and Low-Carbon Nickel-Molybdenum-Chromium Alloy Plate, Sheet, and StripB581 Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy RodB582 Spe

31、cification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and StripB619/B619M Specification for Welded Nickel and Nickel-Cobalt Alloy PipeB622 Specification for Seamless Nickel and Nickel-CobaltAlloy Pipe and TubeB625 Specification for UNS N08925, UNS N08031, UNSN08932, UNS N08926, U

32、NS N08354, UNS N08830, andUNS R20033 Plate, Sheet, and StripB626 Specification for Welded Nickel and Nickel-CobaltAlloy TubeB649 Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Al-loys (UNS N08925, UNS N08031, UNS N08354, andTABLE 1 Fitting Classes for WP GradesClass Construction Nondestructive Examin

33、ationS Seamless NoneW Welded Radiography or UltrasonicWX Welded RadiographyWU Welded UltrasonicB366/B366M 172UNS N08926), and Cr-Ni-Fe-N Low-Carbon Alloy (UNSR20033) Bar and Wire, and Ni-Cr-Fe-Mo-N Alloy (UNSN08936) WireB673 Specification for UNS N08925, UNS N08354, andUNS N08926 Welded PipeB674 Spe

34、cification for UNS N08925, UNS N08354, andUNS N08926 Welded TubeB675 Specification for UNS N08367 Welded PipeB676 Specification for UNS N08367 Welded TubeB677 Specification for UNS N08925, UNS N08354, andUNS N08926 Seamless Pipe and TubeB688 Specification for Chromium-Nickel-Molybdenum-Iron (UNS N08

35、366 and UNS N08367) Plate, Sheet, andStripB690 Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367)Seamless Pipe and TubeB691 Specification for Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and UNS N08367)Rod, Bar, and WireB704 Specification for Welded UNS N06625

36、, UNS N06219and UNS N08825 Alloy TubesB705 Specification for Nickel-Alloy (UNS N06625, N06219and N08825) Welded PipeB710 Specification for Nickel-Iron-Chromium-SiliconAlloyWelded PipeB729 Specification for Seamless UNS N08020, UNSN08026, and UNS N08024 Nickel-Alloy Pipe and TubeB880 Specification fo

37、r General Requirements for ChemicalCheck Analysis Limits for Nickel, Nickel Alloys andCobalt AlloysB899 Terminology Relating to Non-ferrous Metals and Al-loysE165 Practice for Liquid Penetrant Examination for GeneralIndustryE1916 Guide for Identification of Mixed Lots of Metals2.2 ASME Standards:3B1

38、6.9 Wrought Steel Butt Welding FittingsB16.11 Forged Steel Fittings, Socket-Welding and Threaded2.3 Manufacturers Standardization Society of the Valve andFittings Industry Standards:MSS SP-25 Standard Marking Systems for Valves, Fittings,Flanges, and Unions4MSS SP-43 Standard Practice for Light Weig

39、ht StainlessSteel Butt Welding Fittings4MSS SP-95 Sewage (D) Nipples and Bull Plugs4MSS SP-97 Forged Carbon Steel Branch Outlet Fit-tingsSocket Welding, Threaded and Butt Welding Ends4Boiler and Pressure Vessel Code, Section VIII, Division1 Pressure Vessels and Section IX, Welding Qualifica-tions32.

40、4 AWS Standards:5A5.11 Specification for Nickel and Nickel Alloy CoveredWelding ElectrodesA5.14 Specification for Nickel and Nickel-Alloy Bare Weld-ing Rods and Electrodes2.5 ASNT:6SNT-TC-1A Recommended Practice for NondestructiveTesting Personnel Qualification and Certification3. Terminology3.1 Ter

41、ms defined in Terminology B899 shall apply unlessotherwise defined in this standard.4. Ordering Information4.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification. Examples of such requirements include, but arenot limit

42、ed to, the following:4.1.1 Quantity, number of fittings of each kind,4.1.2 Description of Fitting and Nominal Dimensions (stan-dard or special),4.1.3 Alloy Composition,4.1.4 Condition (temper) if applicable.4.1.5 If neither grade of N06625 is specified, Grade 1 willbe supplied.4.1.6 For each Grade o

43、f WP fittings ordered, a Class shouldalso be indicated.4.1.6.1 Grade CR fittings shall not be substituted for fittingsordered to Grade WP, but Grade WP may be substituted forGrade CR.4.1.6.2 For all Classes of WP fittings, unless S, W, WX, orWU is specified by the purchaser, any class may be furnish

44、edat the option of the supplier.4.1.7 Purchaser InspectionState which tests or inspec-tions are to be witnessed (Section 10),4.1.8 Samples for Product (Check Analysis)State whethersamples should be furnished (6.3),4.1.9 Test reports (Section 12), and4.1.10 Supplementary requirements, if any.5. Mater

45、ials and Manufacture5.1 MaterialThe material for wrought welding fittingsmay consist of forgings, rods, bars, plates, sheets, and seamlessor welded pipe that conform to all the requirements of theASTM specifications for the particular product and alloyreferred to in Table 2.5.2 Manufacture:5.2.1 For

46、ging or shaping operations may be performed byhammering, pressing, piercing, extruding, upsetting, rolling,bending, or fusion welding, or by a combination of two or moreof these operations. The forming procedure shall be so appliedthat it will not produce injurious defects in the fittings.3Available

47、 from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.4Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http:/www.mss-.5

48、Available from American Welding Society (AWS), 550 NW LeJeune Rd.,Miami, FL 33126, http:/www.aws.org.6Available fromAmerican Society for Nondestructive Testing (ASNT), P.O. Box28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http:/www.asnt.org.B366/B366M 173TABLE 2 Permissible Raw MaterialsMarkin

49、gAProduct and ASTM DesignationBCorrosion-ResistantFittingsASME PressureFittingsAlloyUNSDesignationPipe or TubePlate,Sheet,or StripBar Forgingand ForgingStockCRN WPN Ni N02200 B161 B162 B160, B564CRNL WPNL Ni, Low C N02201 B161 B162 B160CRNCCWPNCCNi-Cu N04400 B165 B127 B164, B564CR HX WPHX Ni-Cr-Mo-Fe N06002 B619/B619M, B622, B626 B435 B572CR HG WPHG Ni-Cr-Fe-Mo-Cu N06007 B619/B619M, B622, B626 B582 B581CR HC 22 WPHC22 Low C-Ni-Mo-Cr N06022 B619/B619M, B622, B626 B575 B574, B564, B462,B472CRV602 WPV602 Ni-Cr-Fe N06025 B163, B167 B168 B166, B462, B472CR HG 30 WPHG30