IEC 62080 AMD 1-2008 Sound signalling devices for household and similar purposes《家用和类似用途的声音信号发送装置 修改件1》.pdf

《IEC 62080 AMD 1-2008 Sound signalling devices for household and similar purposes《家用和类似用途的声音信号发送装置 修改件1》.pdf》由会员分享，可在线阅读，更多相关《IEC 62080 AMD 1-2008 Sound signalling devices for household and similar purposes《家用和类似用途的声音信号发送装置 修改件1》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62080Edition 1.0 2008-10INTERNATIONAL STANDARD NORME INTERNATIONALESound signalling devices for household and similar purposes Dispositifs de signalisation sonore pour usage domestique et analogue IEC62080:2001/A1:2008 AMENDMENT 1 AMENDEMENT 1 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2

2、008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National C

3、ommittee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf

4、indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous a

5、vez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmaili

6、ec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is

7、kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, tech

8、nical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Elec

9、tropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer

10、Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechniqu

11、e Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez v

12、ous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte

13、, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponib

14、le en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appe

15、l Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22

16、 919 02 11 Fax: +41 22 919 03 00 IEC 62080Edition 1.0 2008-10INTERNATIONAL STANDARD NORME INTERNATIONALESound signalling devices for household and similar purposes Dispositifs de signalisation sonore pour usage domestique et analogue INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNI

17、QUE INTERNATIONALE HICS 29.120.99 PRICE CODECODE PRIXISBN 2-8318-1002-8AMENDMENT 1 AMENDEMENT 1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 62080 Amend. 1 IEC:2008 FOREWORD This amendment has been prepared by I

18、EC technical committee 23: Electrical accessories. The text of this amendment is based on the following documents: FDIS Report on voting 23/450/FDIS 23/457/RVD Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. The com

19、mittee has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, with

20、drawn, replaced by a revised edition, or amended. _ Page 11 1 Scope Replace the first paragraph by the following new text: This International Standard applies to sound signalling devices with integral enclosures or to sound signalling devices intended to be fitted into or supplied with enclosures ac

21、cording to IEC 60670 intended for household and similar purposes with rated voltages not exceeding 250 V a.c. or 250 V d.c. and with rated power inputs not exceeding 100 VA. In these sound signalling devices an indicating light having a rated input power not exceeding 10 VA may also be incorporated.

22、 Page 15 3 Definitions Replace, on page 23, the existing definitions 3.35 and 3.37 by the following new definitions (including the notes): 3.35 earth protected device device in which protection against electric shock does not rely on basic insulation only but which includes an additional safety prec

23、aution such as exposed conductive parts connected to the protective earthing conductor in the fixed wiring of the installation in such a way that exposed conductive parts cannot become live in the event of a failure of the basic insulation NOTE This provision includes a protective conductor in the s

24、upply cable. 62080 Amend. 1 IEC:2008 3 3.37 installation protected device device in which the protection against electric shock does not rely on basic insulation only, but in which additional safety precautions are provided during the installation according to the installation rules NOTE This defini

25、tion is in accordance with 7.2.3 of IEC 61140. Page 29 7 Marking Replace, on page 31, the existing subclause 7.3 by the following new subclause: 7.3 When symbols are used, they shall be as follows: Ampere A Volt . V Volt-ampere, watt VA; W Alternating current (no. 5032 of IEC 60417) . Hertz . Hz Hou

26、rs .h Minutes . min Seconds s Direct current (no. 5031 of IEC 60417) Neutral . N Protective earth (no. 5019 of IEC 60417) Degree of protection according to IEC 60529 .IPXX Ambient temperature limits if outside the range from 0 C to 35 C. Y T Z If a symbol for nature of supply is used, it shall be pl

27、aced next to the marking for rated voltage. NOTE 1 The letter “X“ should be replaced by the relevant number. An additional letter can be used according to IEC 60529. NOTE 2 The letter “Y“ before the “T“ is replaced by the lowest ambient temperature. The letter “Z“ after the “T“ is replaced by the hi

28、ghest ambient temperature. Examples: 10 T 55: means from 10 C up to +55 C 10 T 35: means from 10 C up to +35 C 10 T 55: means from +10 C up to +55 C 0 T 55: means from 0 C up to +55 C 4 62080 Amend. 1 IEC:2008 Page 33 8 Protection against electric shock Replace, on page 35, the text of the eighth pa

29、ragraph by the following new paragraph: In addition, openings in insulating material or unearthed conductive parts are tested by applying the test pin shown in Figure 11 without appreciable force in every possible position. Page 45 10 Normal operation Replace the last paragraph of this Clause by the

30、 following: After the test, the device shall show no damage in the sense of this standard and shall continue to function correctly. Page 47 11 Temperature rise Replace, on page 49, the existing text of subclause 11.6 by the following: 11.6 Plug-in devices shall be inserted into the relevant socket-o

31、utlet in accordance with the relevant national standard. Replace, on page 51, the first paragraph of subclause 11.8 by the following: 11.8 The devices are operated under normal use as specified in clause 10 but while maintaining the ON/OFF ratio as specified by the manufacturer until steady state co

32、nditions are established for continuously rated and intermittent type D devices and until completion of the normal use duty cycles for other devices. Page 51 Subclause 11.9 Add, after the existing text of subclause 11.9, before Table 3, the following new paragraphs: Heat resisting sleeves shall be s

33、o designed that they are reliably retained in position when the device has been mounted. Insulating sleeves shall have adequate mechanical, electrical and thermal strength. The heat resisting sleeve shall be resistant to a temperature of 120 C or withstand the following test: a) Three test specimens

34、 of the sleeve, about 15 cm in length, are subjected to humidity test of 13.4 and subsequently to the insulating resistance and electric strength tests according to clause 14. A suitable un-insulated copper conductor or metal rod is passed through the specimens, and the outside is covered by a metal

35、 foil in such a way that no flashover at the ends of the sample can occur. The measurement of the insulation resistance and the electrical strength test is made between the copper conductors/metal rod and metal foil. b) After the copper conductors/metal rod and metal foil have been removed, the spec

36、imens are placed in a cabinet for 240 h at the temperature of 140 C. c) The specimens are allowed to cool to room temperature and are then prepared as indicated under item a) above. 62080 Amend. 1 IEC:2008 5 Measurement of the insulating resistance and electric strength is then made between the copp

37、er conductors/metal rod and metal foil. Compliance is checked by the insulation resistance values and test voltages specified in Tables 5, 6, 7a, 7b and 8. Page 53 Table 3 Values of maximum temperature rise Add, in the row for “Rubber or PVC insulation of internal and external wiring including suppl

38、y cords”, an additional line, so as to align with IEC 60598: K Rubber or PVC insulation of internal and external wiring including supply cords: without T marking with T marking with protection by a heat resisting sleeve supplied with the device 50 T 25 95 Page 55 Table 4a Temperature limits of windi

39、ngs Replace the table header “Temperature limit C” by the following new table header: Temperature limit (t + 25 K) Page 57 Table 4b Temperature limits of enclosures, supply cable and wiring Replace the table header “Temperature limit C” by the following new table header: Temperature limit (t + 25 K)

40、 Page 57 13.1 Resistance to ageing Convert the second paragraph into a note: NOTE In general, it is only necessary to test devices having or being supplied with enclosures or parts of PVC or similar thermoplastic material and parts of rubber, such as sealing rings and gaskets. Page 59 13.3.1 Replace

41、, on page 61, the penultimate paragraph by the following new text: Parts which can be removed without the aid of a tool are removed except for parts of luminaires and indicating devices. 6 62080 Amend. 1 IEC:2008 Page 73 Subclause 15.3 Replace the existing first paragraph by the following: 15.3 The

42、bases of ordinary surface-type devices are first fixed to a cylinder of rigid steel sheet, with a radius equal to 4,5 times the horizontal distance between fixing holes, but in any case not less than 20 cm. Page 77 15.8 Verification of the outline of covers, cover-plates or actuating members Replace

43、 the existing title by the following new title: 15.8 Verification of the outline of covers, cover-plates or actuating members for flush-mounted products Page 79 15.9 Verification of grooves, holes and reverse tapers Delete the title, text and note of this subclause. Page 83 18 Components Replace the

44、 existing text of subclauses 18.2, 18.3 and 18.4 by the following: 18.2 Plugs and sockets for ELV shall not be interchangeable with the national requirements for plugs and socket outlets of the country where the product is placed on the market or with connectors and device inlets complying with the

45、standard sheets of IEC 60320. 18.3 Plugs and socket-outlets and other connecting devices of interconnecting flexible cables shall not be interchangeable with the national requirements for plugs and socket outlets of the country where the product is placed on the market or with connectors and applian

46、ce inlets complying with the standard sheets of IEC 60320 if direct supply to these parts from the supply mains could give rise to a hazard. 18.4 Plug-in devices shall be fitted with plug portions for insertion into socket-outlets according to the national requirements for plugs and socket outlets o

47、f the country where the product is placed on the market. 19 Terminals Replace the entire text of this clause by the following: Terminals shall meet the requirements of the appropriate tests of IEC 60998 and shall allow the proper connection of supply conductors having cross-sectional areas from 0,5

48、mm2up to and including 1,5 mm2. NOTE Each supply terminal may allow the connection of two or more conductors. Compliance is checked by the appropriate tests according to the IEC 60998 series. 62080 Amend. 1 IEC:2008 7 Page 105 24.2 Glow-wire test Add, after item b) of the first paragraph, the follow

49、ing two paragraphs: A current carrying part or a part of the earthing circuit retained by a mechanical means is considered to be retained in position. The use of grease or the like is not considered to be mechanical means. In case of doubt, to determine whether an insulating material is necessary to retain current carrying parts and parts of the earthing circuit