ISO 10294-1 AMD 1-2014 Fire resistance tests - Fire dampers for air distribution systems - Part 1 Test method Amendment 1《耐火试验 用于空气调节系统的防火阀 第1部分 试验方法 修改件1》.pdf

《ISO 10294-1 AMD 1-2014 Fire resistance tests - Fire dampers for air distribution systems - Part 1 Test method Amendment 1《耐火试验 用于空气调节系统的防火阀 第1部分 试验方法 修改件1》.pdf》由会员分享，可在线阅读，更多相关《ISO 10294-1 AMD 1-2014 Fire resistance tests - Fire dampers for air distribution systems - Part 1 Test method Amendment 1《耐火试验 用于空气调节系统的防火阀 第1部分 试验方法 修改件1》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2014 Fire resistance tests Fire dampers for air distribution systems Part 1: Test method AMENDMENT 1 Essais de rsistance au feu Clapets rsistant au feu pour des systmes de distribution dair Partie 1: Mthode dessai AMENDEMENT 1 INTERNATIONAL STANDARD ISO 10294-1 First edition 1996-12-15 Referenc

2、e number ISO 10294-1:1996/Amd.1:2014(E) AMENDMENT 1 2014-12-15 ISO 10294-1:1996/Amd.1:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by an

3、y means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 G

4、eneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 10294-1:1996/Amd.1:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

5、 of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmen

6、tal, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the

7、 ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possi

8、bility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of

9、 patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as

10、 information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 92, Fire safety, Subcommittee SC 2, Fire containment. ISO 2014 All rights reserved iii Fi

11、re resistance tests Fire dampers for air distribution systems Part 1: Test method AMENDMENT 1 Page 14, 6.3 The amendment adds reference to new Annex A at the end of the first paragraph. 6.3 Thermal release mechanism The thermal release mechanism shall be included in the specimen construction. If the

12、re are alternative release mechanisms where these are in series with the basic thermal release and can be shown to not inhibit the basic release, then only the one thermal release mechanism is required to be tested (see Annex A). New Annex A The amendment adds new informative Annex A. Annex A (infor

13、mative) Alternative thermal mechanism A.1 The following procedure may be adopted by the sponsor with the consent of the testing laboratory to evaluate alternative thermal release mechanisms. A.1.1 Alternative thermal release mechanism(s) can be installed in series with the basic thermal release and

14、tested in accordance with this International Standard. It must be shown that the alternate release mechanism does not inhibit the basic release. A.1.2 The thermal release that is installed with the damper is randomly selected from five identical units. Three of the remaining release mechanisms shall

15、 be evaluated to the requirements in ISO 10294-4 to determine a threshold response time. The threshold shall be the average response time of the three links when tested to the requirements of ISO 10294-4. The response time is used to evaluate the comparative performance of other alternative thermal release mechanisms that are evaluated to the requirements of ISO 10294-4. ISO 10294-1:1996/Amd.1:2014(E) ISO 2014 All rights reserved 1 ISO 10294-1:1996/Amd.1:2014(E) ISO 2014 All rights reserved ICS 13.220.50; 91.140.30 Price based on 1 pages