ANSI IEEE C57 19 03-1996 Standard Requirements Terminology and Test Code for Bushings for DC Applications《直流装置用套管的标准要求、术语和试验规程》.pdf

《ANSI IEEE C57 19 03-1996 Standard Requirements Terminology and Test Code for Bushings for DC Applications《直流装置用套管的标准要求、术语和试验规程》.pdf》由会员分享，可在线阅读，更多相关《ANSI IEEE C57 19 03-1996 Standard Requirements Terminology and Test Code for Bushings for DC Applications《直流装置用套管的标准要求、术语和试验规程》.pdf（29页珍藏版）》请在麦多课文档分享上搜索。

1、 Recognized as anAmerican National Standard (ANSI)The Institute of Electrical and Electronics Engineers, Inc.345 East 47th Street, New York, NY 10017-2394, USACopyright 1997 by the Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 1997. Printed in the United State

2、s of AmericaISBN 1-55937-830-1No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher.IEEE Std C57.19.03-1996IEEE Standard Requirements, Terminology, and Test Code for Bushings for DC Application

3、sSponsorIEEE Transformers Committeeof thePower Engineering SocietyApproved 20 June 1996IEEE Standards BoardApproved January 1997IEEE Standards BoardAbstract:This standard applies to outdoor and indoor power apparatus dc bushings of condensertype that have basic impulse insulation levels of 110 kV an

4、d above for use as components of oil-lled converter transformers and smoothing reactors, as well as air-to-air dc bushings. This stan-dard denes the special terms used, service conditions, rating, general requirements, electricalinsulation characteristics, and test procedure for the bushings for dc

5、application.Keywords:bushings, dc applicationIEEE Standardsdocuments are developed within the IEEE Societies and the Standards Coordinat-ing Committees of the IEEE Standards Board. Members of the committees serve voluntarily andwithout compensation. They are not necessarily members of the Institute.

6、 The standards developedwithin IEEE represent a consensus of the broad expertise on the subject within the Institute as wellas those activities outside of IEEE that have expressed an interest in participating in the develop-ment of the standard.Use of an IEEE Standard is wholly voluntary. The existe

7、nce of an IEEE Standard does not implythat there are no other ways to produce, test, measure, purchase, market, or provide other goods andservices related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at thetime a standard is approved and issued is subject to change brought

8、 about through developments inthe state of the art and comments received from users of the standard. Every IEEE Standard is sub-jected to review at least every ve years for revision or reafrmation. When a document is morethan ve years old and has not been reafrmed, it is reasonable to conclude that

9、its contents,although still of some value, do not wholly reect the present state of the art. Users are cautioned tocheck to determine that they have the latest edition of any IEEE Standard.Comments for revision of IEEE Standards are welcome from any interested party, regardless ofmembership afliatio

10、n with IEEE. Suggestions for changes in documents should be in the form of aproposed change of text, together with appropriate supporting comments.Interpretations: Occasionally questions may arise regarding the meaning of portions of standards asthey relate to specic applications. When the need for

11、interpretations is brought to the attention ofIEEE, the Institute will initiate action to prepare appropriate responses. Since IEEE Standards rep-resent a consensus of all concerned interests, it is important to ensure that any interpretation hasalso received the concurrence of a balance of interest

12、s. For this reason, IEEE and the members of itssocieties and Standards Coordinating Committees are not able to provide an instant response tointerpretation requests except in those cases where the matter has previously received formalconsideration. Comments on standards and requests for interpretati

13、ons should be addressed to:Secretary, IEEE Standards Board445 Hoes LaneP.O. Box 1331Piscataway, NJ 08855-1331USAAuthorization to photocopy portions of any individual standard for internal or personal use isgranted by the Institute of Electrical and Electronics Engineers, Inc., provided that the appr

14、opriatefee is paid to Copyright Clearance Center. To arrange for payment of licensing fee, please contactCopyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA;(508) 750-8400. Permission to photocopy portions of any individual standard for educational class-room use

15、can also be obtained through the Copyright Clearance Center.Note: Attention is called to the possibility that implementation of this standard mayrequire use of subject matter covered by patent rights. By publication of this standard,no position is taken with respect to the existence or validity of a

16、ny patent rights inconnection therewith. The IEEE shall not be responsible for identifying all patents forwhich a license may be required by an IEEE standard or for conducting inquiries intothe legal validity or scope of those patents that are brought to its attention.iiiIntroduction(This introducti

17、on is not part of IEEE Std C57.19.03-1996, IEEE Standard Requirements, Terminology, and Test Codefor Bushings for DC Applications.)This document is based on the standard practices for bushings applied to indoor and outdoor, oil-lled,dc power apparatus, and air-to-air, wall, and roof dc bushings. It

18、is the result of joint efforts of professionalengineers, manufacturers, and users working together under the auspices of the Institute of Electrical andElectronics Engineers (IEEE). Work on this standard was started in 1988 within the Working Group onBushings for DC Applications of the Bushing Subco

19、mmittee of the IEEE Transformers Committee. Theworking group decided to address requirements for these bushings in a self-standing document becausemany problems specic to this type of the bushing were being experienced within the industry and otheravailable standards on bushings were inadequate for

20、this purpose. The main reference for the resulting docu-ment was its counterpart for ac bushings, IEEE Std C57.19.00-1991, IEEE Standard General Requirementsand Test Procedures for Outdoor Power Apparatus Bushings, with portions adapted from the 1984 issue ofIEC Publication 137, Insulating Bushings

21、for Alternating Voltages Above 1000 V. Requirements were alsocoordinated with the CIGRE Joint Working Group 12/14.10 as well as with the HVDC Converter Trans-former and Smoothing Reactor Subcommittee of the IEEE Transformers Committee, which developed stan-dards for these HVDC apparatus during the s

22、ame time frame.The Accredited Standards Committee on Transformers, Regulators, and Reactors, C57, that reviewed andapproved this document, had the following membership at the time of approval:P. E. Orehek, Chairvacant,Vice ChairJohn A. Gauthier, SecretaryOrganization Represented Name of Representati

23、veElectric Light and Power Group E. A. BertoliniT. DiamantisK. HanusM. C. Mingoia (Alt.)P. OrehekG. PaivaJ. SullivanInstitute of Electrical and Electronics EngineersW. B. BinderJ. D. BorstJ. H. HarlowJ. W. MatthewsL. SavioH. D. Smith (Alt.)G. H. VaillancourtNational Electrical Manufacturers Associat

24、ion .G. D. CoulterP. Dewever (Alt.)J. Douglas S. EndersbeA. GhafourianP. HopkinsonK. R. LinsleyR. L. Plaster (Alt.)H. Robin Tennessee Valley AuthorityF. LewisUnderwriters Laboratories, Inc . M. SchackerUS Department of Agriculture, REA J. BohlkUS Department of Energy, Western Area Power Administrati

25、on Kenneth C. WolohonUS Department of Interior, Bureau of Reclamation .R. ChadwickUS Department of the Navy, Civil Engineering CorpsH. P. StickleyivThe Working Group on Bushings for DC Applications had the following membership at the time that thisstandard was developed and approved:Olof Heyman,Chai

26、r Devki N. Sharma,SecretaryThe following persons were on the balloting committee:P. BertolottoF. CostaV. DahindenF. ElliottJ. FoldiJ. FrostD. A. GilliesA. J. JonnattiS. LindgrenJ. C. RiboudF. RichensH. RuevekampP. SinghW. W. SteinL. WagenaarW. A. YoungEdward J. AdolphsonD. J. AllanRaymond Allustiart

27、iMichael S. AltmanGlenn AndersenJ. C. ArnoldJ. ArteagaJ. AubinDonald E. AyersRoy A. BancroftRon L. BarkerDavid A. BarnardE. BertoliniWallace B. BinderJ. H. BishopW. E. BoettgerJ. V. BonucchiJohn D. BorstC. V. BrownM. CambreD. J. CashD. ChuThomas F. ClarkJ. L. CorkranDan W. CroftsJohn C. CrouseV. Dah

28、indenJohn N. DavisR. C. DegeneffT. DiamantisLarry E. DixR. F. DudleyJohn A. EbertK. EdwardsFred E. ElliottD. J. FallonP. T. FeghaliJeffrey A. FleemanMichael A. FranchekJerry M. FrankDudley L. GallowayA. A. GhafourianDonald A. GilliesR. S. GirgisR. D. GrahamRobert L. GrubbR. L. GrunertF. J. Gryszkiew

29、iczMichael E. HaasGeoff H. HallE. HaniqueN. Wayne HansenKenneth S. HanusJames H. HarlowFrank W. HeinrichsWilliam R. HenningK. R. HightonPeter J. HoeerPhilip J. HopkinsonJ .W. HowardEdgar HowellsJ. HuntY. Peter IijimaC. W. JohnsonAnthony J. JonnattiR. D. JordanE. KallaurJ. J. KellySheldon P. KennedyW

30、illiam N. KennedyJames P. KinneyAlexander D. KlineJ. G. LackeyMichael Y. LauJ. P. LazarFrank A. LewisHarold F. LightS. R. LindgrenLarry A. LowdermilkDonald L. LoweRichard I. LoweDavid S. LyonJoseph MaWilliam A. MaguireK.T. MassoudaJohn W. MatthewsA. D. McCainJack W. McGillCharles J. McMillenW. J. Mc

31、NuttCharles P. McShaneRoss McTaggartSam P. MehtaC. Kent MillerMatthew C. MingoiaRussell E. MinkwitzMichael I. MitelmanHarold R. MooreW. E. MorehartD. H. MulkeyC. R. MurrayR. J. MusilWilliam H. MutschlerCarl G. NiemannE. T. NortonPaul E. OrehekGerald A. PaivaKlaus PappBipin K. PatelWesley F. Patterso

32、n, Jr.J. M. PattonPaulette A. PayneLarry C. PearsonThomas J. PekarekDan D. PercoMark D. PerkinsV. Q. PhamLinden W. PierceR. L. PlasterDonald W. PlattsBertrand PoulinJeewan L. PuriVadim RaffJ. D. RambozCharles T. RaymondPierre RiffonPeter G. RisseS. M. A. RizviChris A. RobbinsR. B. RobertsonA. L. Rob

33、insonJ. R. RossettiG. W. RoweMahesh P. SampatLeo J. SavioWilliam E. SaxonRobert W. ScheuDevki N. SharmaV. ShenoyHyeong J. SimJ. W. SmithvWhen the IEEE Standards Board approved this standard on 20 June 1996, it had the following membership:Donald C. Loughry,ChairRichard J. Holleman,Vice ChairAndrew G

34、. Salem,Secretary*Member EmeritusAlso included are the following nonvoting IEEE Standards Board liaisons:Satish K. AggarwalAlan H. CooksonChester C. TaylorRochelle L. SternIEEE Standards Project EditorJ. E. SmithJ. E. SmithStephen D. SmithRonald J. StaharaW. W. SteinRon W. SonerJohn C. SullivanDavid

35、 SundinLouis A. TauberJames B. TempletonV. ThenappanJames A. ThompsonR. W. ThompsonThomas P. TraubE. R. TrummerGeorges H. VaillancourtRobert A .VeitchLoren B.WagenaarBarry H. WardR. J. WheartyD. W. WhitleyA. L. WilksCharles W. WilliamsGilles A. BarilClyde R. CampJoseph A. CannatelliStephen L. Diamon

36、dHarold E. EpsteinDonald C. FleckensteinJay Forster*Donald N. HeirmanBen C. JohnsonE. G. Al KienerJoseph L. Koepnger*Stephen R. LambertLawrence V. McCallL. Bruce McClungMarco W. MigliaroMary Lou PadgettJohn W. PopeJose R. RamosArthur K. ReillyRonald H. ReimerGary S. RobinsonIngo RschJohn S. RyanChee

37、 Kiow TanLeonard L. TrippHoward L. WolfmanviContentsCLAUSE PAGE1. Overview 11.1 Scope 11.2 Purpose. 12. References 13. Definitions 24. Service conditions 64.1 Usual service conditions 64.2 Unusual service conditions 65. Rating. 75.1 Rated maximum line-to-ground voltage 75.2 Rated frequency . 85.3 Ra

38、ted dielectric strength 85.4 Rated current 96. General requirements. 106.1 Electrical requirements 106.2 Mechanical requirements. 116.3 Nameplate markings 126.4 Specific creepage distance . 127. Test procedure 127.1 Test conditions. 127.2 Design tests 137.3 Routine tests. 217.4 Special tests 231IEEE

39、 Standard Requirements, Terminology, and Test Code Bushings for DC Applications1. Overview1.1 ScopeThis standard applies to outdoor and indoor power apparatus dc bushings of condenser type that have basicimpulse insulation levels of 110 kV and above for use as components of oil-lled converter transf

40、ormers andsmoothing reactors, as well as air-to-air dc bushings. This standard does not apply to the following:a) High-voltage cable terminations (potheads)b) Bushings for instrument transformersc) Bushings for test transformersd) Bushings in which the internal insulation is provided by a gase) Bush

41、ings applied with gaseous insulation (other than air at atmospheric pressure) external to thebushingf) Bushings for distribution class transformers1.2 PurposeThis standard denes the special terms used, service conditions, rating, general requirements, electrical insu-lation characteristics, and test

42、 procedure for the bushings for dc application.2. ReferencesThis standard shall be used in conjunction with the following publications. When the following standards aresuperseded by a revision, the revision shall notapply.ANSI C84.1-1982, Electric Power Systems and EquipmentVoltage Ratings (60 Hz).1

43、1ANSI publications are available from the Sales Department, American National Standards Institute, 11 West 42nd Street, 13th Floor,New York, NY 10036, USA.IEEEStd C57.19.03-1996 IEEE STANDARD REQUIREMENTS, TERMINOLOGY, AND TEST CODE2ANSI C92.2-1981, Power SystemsPreferred Voltage Ratings for Alterna

44、ting-Current Electrical Systemsand Equipment Operating at Voltages above 230 kV Nominal (revision and redesignation of ANSI C92.2-1987).IEC 137 (1984), Insulating bushings for alternating voltages above 1000 V.2IEC 270 (1981), Partial discharge measurements.IEC 60-1 (1989), High-voltage test techniq

45、ues. Part 1: General denitions and test requirements.IEEE Std 4-1995, IEEE Standard Techniques for High-Voltage Testing (ANSI).3IEEE Std 100-1992, IEEE Dictionary of Electrical and Electronics Terms (ANSI).IEEE Std 1313-1993, IEEE Standard for Power SystemsInsulation Coordination (formerly C92.1)(AN

46、SI).IEEE Std C57.19.100-1995, IEEE Guide for Application of Power Apparatus Bushings (ANSI).IEEE Std C57.19.00-1991, IEEE General Requirements and Test Procedures for Outdoor Apparatus Bush-ings (ANSI).IEEE Std C57.19.01-1991, IEEE Standard Performance Characteristics and Dimensions for Outdoor Appa

47、-ratus Bushings (ANSI).IEEE Std C57.113-1991, IEEE Guide for Partial Discharge Measurement in Liquid-Filled Power Trans-formers and Shunt Reactors (ANSI).3. DenitionsFor terms not specically dened in this standard, see IEEE Std 100-1992.43.1 ambient temperature: The temperature of the surrounding ai

48、r that comes in contact with the bushingand device or equipment in which the bushing is mounted.3.2 arcing distance: The shortest external tight-string distance measured over the insulating envelopebetween the metal parts at line potential and ground. Formerly referred to as striking distanceor flas

49、hoverdistance.3.3 absorption current: Current resulting from charge absorbed in the dielectric as a result of polarization.3.4 bushing: An insulating structure, including a through conductor or providing a central passage for sucha conductor, with provision for mounting on a barrier, conducting or otherwise, for the purpose of insulatingthe conductor from the barrier and conducting current from one side of the barrier to the other.2IEC publications are available from IEC Sales Department, Case Postale 131, 3, rue de Varemb, CH-1211, Genve 20, Switzerland/Suisse