IEC TS 62344-2013 Design of earth electrode stations for high-voltage direct current (HVDC) links - General guidelines《高压直流(HVDC)连接用接地电极站的设计.通用导则》.pdf

《IEC TS 62344-2013 Design of earth electrode stations for high-voltage direct current (HVDC) links - General guidelines《高压直流(HVDC)连接用接地电极站的设计.通用导则》.pdf》由会员分享，可在线阅读，更多相关《IEC TS 62344-2013 Design of earth electrode stations for high-voltage direct current (HVDC) links - General guidelines《高压直流(HVDC)连接用接地电极站的设计.通用导则》.pdf（94页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC/TS 62344 Edition 1.0 2013-01 TECHNICAL SPECIFICATION Design of earth electrode stations for high-voltage direct current (HVDC) links General guidelines IEC/TS 62344:2013(E) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless

2、otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any

3、 questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Gene

4、va 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IE

5、C publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of cr

6、iteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line a

7、nd also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrote

8、chnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC/TS 62344 Edition 1.0 2013-01 TECHNICAL SPECIFICATION Design of earth electro

9、de stations for high-voltage direct current (HVDC) links General guidelines INTERNATIONAL ELECTROTECHNICAL COMMISSION XC ICS 29.240.99 PRICE CODE ISBN 978-2-83220-575-4 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an

10、 authorized distributor. colour inside 2 TS 62344 IEC:2013(E) CONTENTS FOREWORD . 7 INTRODUCTION . 9 1 Scope . 10 2 Normative references . 10 3 Terms and definitions . 10 3.22 current-releasing density . 13 4 System conditions 14 4.1 General principles . 14 4.2 System parameters related to earth ele

11、ctrode design 14 4.2.1 Amplitude and duration of the current 14 4.2.2 Polarity 14 4.2.3 Designed lifespan 15 4.2.4 Common earth electrodes 15 5 Design of land electrode stations 15 5.1 Main technical parameters . 15 5.1.1 General principles . 15 5.1.2 Temperature rise . 16 5.1.3 Earthing resistance

12、16 5.1.4 Step voltage 17 5.1.5 Touch voltage 17 5.1.6 Current density 17 5.1.7 Field intensity in fish ponds . 18 5.2 Electrode site selection and parameter measurement 18 5.2.1 General principles . 18 5.2.2 Data collection survey . 18 5.2.3 Distance from converter station (substation) 18 5.2.4 Envi

13、ronment conditions . 19 5.2.5 Terrain and landform . 19 5.2.6 Measurement of soil parameters 19 5.2.7 Geological exploration . 19 5.2.8 Topographical map 19 5.2.9 Values selected during design . 19 5.3 Earth electrode and associated components 20 5.3.1 General principles for material selection 20 5.

14、3.2 Selection of feeding rods and characteristics . 20 5.3.3 Chemical and physical properties of petroleum coke 21 5.3.4 Current-guiding system 21 5.3.5 Bus 22 5.3.6 Electrode line monitoring device 22 5.4 Electrode arrangement 22 5.4.1 General principles . 22 5.4.2 Filling coke 22 5.4.3 Selection o

15、f earth electrode shape. 22 5.4.4 Earth electrode corridor (right of way) 23 5.4.5 Distance between sub-electrodes in the arrangement 23 5.4.6 Burial depth of the earth electrodes . 23 TS 62344 IEC:2013(E) 3 5.4.7 Segmentation of earth electrodes 24 5.5 Minimum size of earth electrode 24 5.5.1 Gener

16、al principles . 24 5.5.2 Total earth electrode length . 24 5.5.3 Side length of coke section 24 5.5.4 Diameter of feeding rods . 25 5.6 Current guiding system 26 5.6.1 General principles . 26 5.6.2 Placement of the current-guiding wire 26 5.6.3 Connection of current-guiding wire 26 5.6.4 Selection o

17、f current-guiding wire cross-section 27 5.6.5 Insulation of the current-guiding wire . 27 5.6.6 Disconnecting switch . 27 5.6.7 Connection of the feeding cable. 27 5.6.8 Connection of jumper cables . 28 5.6.9 Selection of cable structure . 28 5.6.10 Selection of cable cross-section 28 5.6.11 Selecti

18、on of cable insulation 28 5.6.12 Cable welding position . 29 5.6.13 Welding . 29 5.6.14 Mechanical protection for cable . 29 5.7 Auxiliary facilities 29 5.7.1 Online monitoring 29 5.7.2 Soil treatment 29 5.7.3 Exhaust equipment 30 5.7.4 Fence 30 5.7.5 Marker . 30 6 Design of sea electrode station an

19、d shore electrode station . 30 6.1 Main technical parameters . 30 6.1.1 Temperature rise . 30 6.1.2 Earthing resistance 30 6.1.3 Step voltage 31 6.1.4 Touch voltage 32 6.1.5 Voltage gradient in water . 32 6.1.6 Current density 32 6.2 Electrode site selection and parameter measurement 32 6.2.1 Genera

20、l principles . 32 6.2.2 Data collection survey . 32 6.2.3 Distance from converter station (substation) 32 6.2.4 Environment conditions . 33 6.2.5 Measurement of soil parameters 33 6.3 Earth electrode and associated components 33 6.3.1 General principles for material selection 33 6.3.2 Common feeding

21、 rods and characteristics . 33 6.3.3 Chemical properties of petroleum coke 34 6.3.4 Current-guiding system 34 6.3.5 Bus 34 6.3.6 Electrode line monitoring device 34 6.4 Electrode arrangement 34 4 TS 62344 IEC:2013(E) 6.4.1 General principles . 34 6.4.2 Filling coke 34 6.4.3 Selection of earth electr

22、ode shape. 34 6.4.4 Segmentation of earth electrodes 35 6.5 Current-guiding system . 35 6.5.1 Placement of the current-guiding wire 35 6.5.2 Connection of current-guiding system 35 6.5.3 Selection of cable cross-section 36 6.5.4 Insulation of the current-guiding system 36 6.5.5 Selection of cable st

23、ructure . 36 6.5.6 Mechanical protection for cable . 36 6.6 Auxiliary facilities 36 7 Impact on surrounding facilities and mitigation measures . 37 7.1 Impact on insulated metallic structures and mitigation measures . 37 7.1.1 General principles . 37 7.1.2 Relevant limits . 37 7.1.3 Mitigation measu

24、res 37 7.2 Impact on bare metallic structures . 37 7.2.1 General principles . 37 7.2.2 Relevant limits . 37 7.2.3 Mitigation measures 37 7.3 Impact on the power system (power transformer, grounding network, and surrounding towers) . 38 7.3.1 General principles . 38 7.3.2 Relevant limits . 38 7.3.3 M

25、itigation measures 38 7.4 Impact on electrified railway 38 7.5 Other facilities (such as greenhouses and water pipes) . 39 Annex A (informative) Basic concepts of earth electrodes 40 Annex B (informative) Soil parameter measurement method 52 Annex C (informative) Electrode line design . 60 Annex D (

26、informative) Assessment of measurement method 63 Annex E (informative) Earth electrode electrical parameter calculation method 67 Annex F (informative) Thermal time constant . 78 Annex G (informative) Schematic diagram of online monitoring system 80 Annex H (informative) Calculation method for corro

27、sion of nearby metal structures caused by earth electrodes . 81 Annex I (informative) Calculation method for d.c. current flowing through a.c. transformer neutral near earth electrodes . 83 Annex J (informative) Chemical aspects 86 Annex K (informative) Simple introduction of shore electrodes . 87 B

28、ibliography 89 Figure 1 Electrode cross-section 22 Figure 2 Vertical arrangement 23 Figure 3 Placement of the current-guiding wire 26 Figure 4 Feeding cable 28 TS 62344 IEC:2013(E) 5 Figure 5 Resistivity layers with sea or shore electrodes . 31 Figure 6 Sea electrode . 34 Figure 7 Sea bottom electro

29、de with titanium nets . 35 Figure 8 Titanium net . 36 Figure 9 Impact of earth electrodes on a.c. systems (transformer, grounding network, tower) . 38 Figure A.1 HVDC power transmission system structure 40 Figure A.2 Schematic diagram of the structure of a monopolar earth (sea water) return system 4

30、1 Figure A.3 Schematic diagram of the structure of monopolar metallic return system 41 Figure A.4 Schematic diagram of the structure of bipolar neutral grounded at both ends . 42 Figure A.5 Schematic diagram of the structure of bipolar neutral grounded at one end 42 Figure A.6 Schematic diagram of t

31、he structure of bipolar neutral line . 43 Figure A.7 Schematic diagram of touch voltage and step voltage . 44 Figure A.8 Schematic diagram of single circular earth electrode 45 Figure A.9 Axial distribution of step voltage of single circular earth electrode . 45 Figure A.10 3-D distribution of step

32、voltage of single circular earth electrode . 46 Figure A.11 Schematic diagram of double circular earth electrode . 46 Figure A.12 Axial distribution of step voltage of double circular earth electrode . 46 Figure A.13 3-D distribution of step voltage of double circular earth electrode . 47 Figure A.1

33、4 Schematic diagram of triple circular earth electrode 47 Figure A.15 Axial distribution of step voltage of triple circular earth electrode 47 Figure A.16 3-D distribution of step voltage of triple circular earth electrode 48 Figure B.1 Equivalent circuit of Wenner method . 54 Figure B.2 Equivalent

34、circuit of Schlumberger method . 54 Figure B.3 Equivalent circuit of dipole-dipole method . 55 Figure E.1 shape equivalent circuit of an individual earth electrode unit 67 Figure E.2 Ohms Law applied to cylinder conductor 68 Figure E.3 Continuity of axial component of the electric field in the soil

35、and in the conductor 68 Figure E.4 Spatial division of the earth electrode . 68 Figure E.5 Network for solving axis current 69 Figure E.6 Horizontally layered soil 71 Figure E.7 Geometrical structure of a tetrahedron unit . 72 Figure E.8 Structure of a double-circle d.c. earth electrode 76 Figure E.

36、9 Ground potential and step voltage distribution of a double-circle earth electrode 77 Figure F.1 Earth electrode temperature rise characteristics 78 Figure G.1 Schematic diagram of earth electrode online monitoring system . 80 Figure H.1 Calculation of current flowing through a metal pipe . 82 Figu

37、re I.1 Schematic diagram of ground resistance network and underground voltage source 83 Figure I.2 Circuit model for the analysis of d.c. distribution of a.c. systems 85 Figure K.1 Top view of shore electrode, beach type . 87 6 TS 62344 IEC:2013(E) Figure K.2 Shore electrode, pond type . 87 Table 1

38、Composition of iron-silicon alloy electrode . 21 Table 2 Chemical composition of the coke after calcination 21 Table 3 Physical properties of petroleum coke used for earth electrodes . 21 Table 4 Electric corrosion characteristics of different materials 26 Table B.1 Soil (rock) resistivity . 52 Tabl

39、e B.2 Soil thermal capacity 53 Table B.3 Soil thermal conductivity 53 Table B.4 Number of measurement points with different pole distances . 56 Table E.1 Model of soil with two layers 77 TS 62344 IEC:2013(E) 7 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DESIGN OF EARTH ELECTRODE STATIONS FOR HIGH-VO

40、LTAGE DIRECT CURRENT (HVDC) LINKS GENERAL GUIDELINES FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operati

41、on on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “I

42、EC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this prepar

43、ation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consen

44、sus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts ar

45、e made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications tr

46、ansparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independen

47、t certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liabil

48、ity shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (includ

49、ing legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subje