IEC TS 62257-5-2015 Recommendations for renewable energy and hybrid systems for rural electrification - Part 5 Protection against electrical hazards《农村电气化用可再生能源和混合系统的建议.第5部分 电气事故的防护》.pdf

《IEC TS 62257-5-2015 Recommendations for renewable energy and hybrid systems for rural electrification - Part 5 Protection against electrical hazards《农村电气化用可再生能源和混合系统的建议.第5部分 电气事故的防护》.pdf》由会员分享，可在线阅读，更多相关《IEC TS 62257-5-2015 Recommendations for renewable energy and hybrid systems for rural electrification - Part 5 Protection against electrical hazards《农村电气化用可再生能源和混合系统的建议.第5部分 电气事故的防护》.pdf（50页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC TS 62257-5 Edition 2.0 2015-12 TECHNICAL SPECIFICATION Recommendations for renewable energy and hybrid systems for rural electrification Part 5: Protection against electrical hazards IEC TS 62257-5:2015-12(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Swi

2、tzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the coun

3、try of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Vare

4、mb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC pub

5、lications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bib

6、liographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (

7、reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also o

8、nce a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnica

9、l Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77

10、, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC TS 62257-5 Edition 2.0 2015-12 TECHNICAL SPECIFICATION Recommendations for renewable energ

11、y and hybrid systems for rural electrification Part 5: Protection against electrical hazards INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 27.160 ISBN 978-2-8322-3070-1 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an

12、 authorized distributor. colour inside 2 IEC TS 62257-5:2015 IEC 2015 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope 8 2 Normative references 8 3 Terms and definitions 9 4 Classification of decentralised rural electrification systems 11 5 Protection against electric shock . 11 5.1 General . 11 5.2 R

13、equirements on the d.c. side of a DRES . 11 5.3 Requirements on the a.c. side of a DRES . 12 5.3.1 General . 12 5.3.2 TT system 12 5.3.3 TN system . 12 6 Protection against overcurrent . 13 6.1 General . 13 6.2 Protection against overload currents . 13 6.3 Protection against short-circuits 13 7 Prot

14、ection against risk of fire . 13 8 Protection against effects of lightning 14 8.1 Principle . 14 8.2 Examples 14 8.3 Protection against overvoltage 14 8.4 Protection against direct lightning . 14 9 Determination of the pick up area of a rod or wire (see IEC 62305-3:2010) 14 9.1 General . 14 9.2 Oper

15、ational conditions and external influences . 14 9.3 Wiring system . 15 9.4 Isolation and switching 15 9.4.1 Isolation . 15 9.4.2 Over-current protective devices . 16 9.4.3 Residual Current Devices (RCD) . 17 9.5 Surge protective devices . 17 9.6 Earthing arrangement, protective conductors and protec

16、tive bonding conductors 18 9.6.1 Earth electrodes 18 9.6.2 Protective bonding conductors . 19 10 Verification 19 11 Operation and maintenance . 19 Annex A (informative) Protection against electric shock in electrical installations . 20 A.1 Protection against electric shock . 20 A.2 Automatic disconn

17、ection of supply 20 A.2.1 General . 20 A.2.2 In TN systems . 21 A.2.3 In TT systems 21 A.3 Double or reinforced insulation . 22 IEC TS 62257-5:2015 IEC 2015 3 A.4 Extra-low-voltage (SELV and PELV) . 22 A.5 Electrical separation . 22 A.6 Additional protection . 23 Annex B (informative) Types of LV di

18、stribution systems earthing . 24 B.1 Terms and definitions 24 B.2 Types of system earthing used in DRES (Figures are from IEC 60364-1:2005) . 25 B.2.1 General . 25 B.2.2 AC TN systems 27 B.2.3 AC TT systems 34 B.2.4 DC distribution systems . 36 Annex C (informative) Classification of electrical equi

19、pment 41 C.1 Classification of residual current devices (RCDs) (see IEC 61008, IEC 61009, IEC 60755, IEC 60947-2, IEC 62423) 41 C.2 Classification of circuit breakers for a.c. operation (see IEC 60898-1, IEC 60947-2) 42 C.3 Classification of surge protective devices (see IEC 61643-11) 43 Annex D (in

20、formative) General information concerning protection against lightning . 44 D.1 General . 44 D.2 Protection against lightning Principles 45 Bibliography 46 Figure B.1 General outline of the distribution system . 24 Figure B.2 Distribution system of the smallest type 25 Figure B.3 TN-S system 3-phase

21、, 4-wire with separate neutral conductor and protective conductor throughout the distribution system 28 Figure B.4 TN-S system 3-phase, 3-wire with separate earthed line conductor and protective conductor throughout the distribution system 29 Figure B.5 TN-S system 3-phase, 3-wire with protective co

22、nductor and no distributed neutral conductor throughout the distribution system 30 Figure B.6 TN-C-S system 3-phase, 4-wire where the PEN conductor is separated into the protective conductor PE and the neutral conductor N elsewhere in the electrical installation . 31 Figure B.7 TN-C-S system 3-phase

23、, 4-wire where the PEN conductor is separated into the protective conductor PE and the neutral conductor N at the origin of the electrical installation . 32 Figure B.8 TN-C-S system single-phase, 2-wire where the PEN conductor is separated into the protective conductor PE and the neutral conductor N

24、 at the origin of the electrical installation . 32 Figure B.9 TN-C system 3-phase, 4-wire with neutral and protective conductor functions combined in a single conductor throughout the distribution system 33 Figure B.10 TN-S multiple source system 3-phase, 4-wire with separate protective conductor an

25、d neutral conductor to current using equipment . 34 Figure B.11 TT system 3-phase, 4-wire with earthed protective conductor and neutral conductor throughout the distribution system 35 Figure B.12 TT system 3-phase, 3-wire with earthed protective conductor and no distributed neutral conductor through

26、out the distribution system . 35 Figure B.13 TN-S d.c. system 37 Figure B.14 TN-C d.c. system 38 Figure B.15 TN-C-S d.c. system . 39 4 IEC TS 62257-5:2015 IEC 2015 Figure B.16 TT d.c. system 40 Figure D.1 Example of effects of a lightning stroke 44 Table 1 Typology of decentralized electrification s

27、ystems 11 Table 2 Rated operating residual current of the protective device depending on the value of the earthing resistance 12 Table 3 Number of protected poles with regard to the characteristics of the distribution system 16 IEC TS 62257-5:2015 IEC 2015 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION

28、 _ RECOMMENDATIONS FOR RENEWABLE ENERGY AND HYBRID SYSTEMS FOR RURAL ELECTRIFICATION Part 5: Protection against electrical hazards FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC

29、National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, P

30、ublicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- go

31、vernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IE

32、C on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are acce

33、pted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote internatio

34、nal uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the la

35、tter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users sho

36、uld ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other dam

37、age of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of

38、 the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent righ

39、ts. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obtained for the publication of an International Standard, despite rep

40、eated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to review within three years of publication to decide whether they ca

41、n be transformed into International Standards. IEC 62257-5, which is a technical specification, has been prepared by IEC technical committee 82: Solar photovoltaic energy systems. 6 IEC TS 62257-5:2015 IEC 2015 This second edition cancels and replaces the first edition issued in 2005. It constitutes

42、 a technical revision. The main technical changes with regard to the previous edition are as follows: redefine the maximum AC voltage from 500 V to 1 000 V, the maximum DC voltage from 750 V to 1 500 V; removal of the limitation of 100 kVA system size. Hence the removal of the word “small” in the ti

43、tle and related references in this technical specification. This technical specification is to be used in conjunction with the IEC 62257 series (specifically IEC TS 62257-1 to IEC TS 62257-6). The text of this technical specification is based on the following documents: Enquiry draft Report on votin

44、g 82/950/DTS 82/1001A/RVC Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62257 serie

45、s, published under the general title Recommendations for renewable energy and hybrid systems for rural electrification, can be found on the IEC website. Future standards in this series will carry the new general title as cited above. Titles of existing standards in this series will be updated at the

46、 time of the next edition. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be transformed into

47、 an International standard, reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be u

48、seful for the correct understanding of its contents. Users should therefore print this document using a colour printer. IEC TS 62257-5:2015 IEC 2015 7 INTRODUCTION The IEC 62257 series intends to provide to different players involved in rural electrification projects (such as project implementers, p

49、roject contractors, project supervisors, installers, etc.) documents for the setting up of renewable energy and hybrid systems with AC voltage below 1 000 V and DC voltage below 1 500 V. These documents are recommendations: to choose the right system for the right place; to design the system; to operate and maintain the system. These documents are focused only on rural electrification, concentrating on, but not specific to developing countries. They should