IEC 62491-2008 Industrial systems installations and equipment and industrial products - Labelling of cables and cores《工业系统、装置和设备及工业产品.电缆和电线的标签》.pdf

《IEC 62491-2008 Industrial systems installations and equipment and industrial products - Labelling of cables and cores《工业系统、装置和设备及工业产品.电缆和电线的标签》.pdf》由会员分享，可在线阅读，更多相关《IEC 62491-2008 Industrial systems installations and equipment and industrial products - Labelling of cables and cores《工业系统、装置和设备及工业产品.电缆和电线的标签》.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62491 Edition 1.0 2008-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial systems, installations and equipment and industrial products Labelling of cables and cores Systmes industriels, installations et appareils et produits industriels Etiquetage des cbles et des conducteurs isols IEC 6

2、2491:2008 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without pe

3、rmission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee

4、for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI o

5、u du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office

6、3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About I

7、EC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to

8、search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new pub

9、lications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as th

10、e International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41

11、22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu techniqu

12、e des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des reche

13、rches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille d

14、eux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les term

15、es quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Se

16、rvice clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62491 Edition 1.0 2008-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial systems, installations and equipment and industrial products Labelling of cables and cores Systmes industriels, installat

17、ions et appareils et produits industriels Etiquetage des cbles et des conducteurs isols INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 01.110; 29.020.20 PRICE CODE CODE PRIX ISBN 2-8318-9663-0 2 62491 IEC:2008 CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2

18、 Normative references .7 3 Terms and definitions .8 4 Rules9 4.1 General requirements9 4.2 Use of designated cable cores.10 4.3 Use of additional labelling .10 5 Identification labelling.11 5.1 General .11 6 Connection labelling .14 6.1 General .14 6.2 Local-end connection labelling 14 6.3 Remote-en

19、d connection labelling.15 6.4 Both-end connection labelling16 7 Signal labelling.17 7.1 General .17 7.2 Labelling by signal designation17 7.3 Labelling of cables for certain designated conductors18 8 Composite labelling 19 9 Arrangement of additional labelling.20 9.1 General .20 9.2 Relative positio

20、ns of the labelling 20 9.3 Characters to be used .20 10 Correspondence between labelling and documentation.21 11 Conformance to this standard.21 Annex A (informative) Examples of labelling .22 Bibliography30 Figure 1 Example of identification labelling of a single core cable (W23) and of a multi-cor

21、e cable (W24) in which also the different cores are labelled 12 Figure 2 Example of identification labelling of cores where the initial part of the reference designation has been partly omitted13 Figure 3 Example of local-end connection labelling14 Figure 4 Example of remote-end connection labelling

22、 for a connection inside a unit.15 Figure 5 Example of remote-end connection labelling for a cable between different units .16 Figure 6 Example of both-end connection labelling 17 Figure 7 Example of local-end connection labelling combined with signal labelling.19 Figure 8 Example of composite label

23、ling in which both-end connection labelling is used together with identification labelling and signal labelling.19 Figure 9 Examples of arrangements of labelling on cores or cables. 20 Figure A.1 Circuit diagram used as a basis for the examples .22 62491 IEC:2008 3 Figure A.2 Example of identificati

24、on labelling.23 Figure A.3 Example of local-end labelling 24 Figure A.4 Example of both-end connection labelling .25 Figure A.5 Example of local end connection labelling with additional information .26 Figure A.6 Example of signal labelling .27 Figure A.7 Example of composite labelling.28 Figure A.8

25、 Example where use is made of the cable colours29 Table 1 Example of connection table in which the cable cores are identified by means of codes for their colour.10 Table 2 Connection table corresponding to Figure 1 with labelling .12 Table 3 Connection table corresponding to Figure 2 with labelling

26、.13 Table 4 Marking of certain designated conductors18 Table 5 Methods of labelling defined in this standard.21 4 62491 IEC:2008 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL SYSTEMS, INSTALLATIONS AND EQUIPMENT AND INDUSTRIAL PRODUCTS LABELLING OF CABLES AND CORES FOREWORD 1) The Internati

27、onal Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electroni

28、c fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; a

29、ny IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standa

30、rdization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has rep

31、resentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, I

32、EC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publ

33、ications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with a

34、n IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal i

35、njury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative reference

36、s cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for iden

37、tifying any or all such patent rights. International Standard IEC 62491 has been prepared by IEC technical committee 3: Information structures, documentation and graphical symbols. The text of this standard is based on the following documents: CDV Report on voting 3/849/CDV 3/881/RVC Full informatio

38、n on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 62491 IEC:2008 5 The committee has decided that the contents of this publication will remain uncha

39、nged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 62491 IEC:2008 INTRODUCTION Additional labell

40、ing of cables and cores might be required within larger systems or installations with many cores of the same colour or with many cables, and where therefore the use of the designations provided by the cable manufacturer only would be ambiguous. Due consideration should be given to the fact that addi

41、tional labelling will cause additional cost, usually increasing with the number of characters in the labelling string and the number of different labelling elements. The available space may also impose restrictions with regard to the number of characters, their height and the length of the labelling

42、. As a general rule the use of additional labelling should therefore be limited to a necessary minimum and be kept as short as practicable. However, also the advantages and benefits should be taken into considerations in choosing additional labelling of cables and cores. It is important to notice th

43、at a single machine or a system has different needs of information in the different phases of its lifecycles (assembling, production, service and maintenance). Additional labelling of cables and cores gives the following advantages: the possibilities to communicate and identify signals and connectio

44、ns across different involved engineering disciplines and departments like: process engineering, software engineering, electrical engineering, mechanical/fluid engineering, control engineering; minimizing the time used to locate an eventual error (and the reason for it) in the test phase; saving time

45、 when locating an eventual error (and the reason for it) in the service and maintenance phase; remove the doubt of which core should be connected to which terminal, when replacing components that are placed close to each other; if used in pre-planning, it gives a clear view for panel-builders, elect

46、ricians/technicians; service/maintenance and system controllers which will minimize misunderstandings regarding connections. Besides being used in connections between terminal blocks, labelling can also be used when single core cables connect components inside units as: cubicle, pulpit, case, etc.;

47、such methods make possible: a rapid and secure cabling between the terminals of two objects; a rapid visual check of cabling, not necessarily looking up in the circuit diagrams; a correct and secure change of an object during the maintenance operations of plants. 62491 IEC:2008 7 INDUSTRIAL SYSTEMS,

48、 INSTALLATIONS AND EQUIPMENT AND INDUSTRIAL PRODUCTS LABELLING OF CABLES AND CORES 1 Scope This standard provides rules and guidelines for the labelling of cables and cores/conductors used in industrial installations, equipment and products, in order to maintain a clear relation between the technica

49、l documentation and the actual equipment and for other purposes. The following methods are described and designated: use of coloured cables and designated cores; additional identification labelling; additional connection labelling; and additional signal labelling. The physical design of the labels, the material to be used for the labels as well as cable m